• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.4
• /
• pp.1-9
• /
• 2009

This paper investigates inelastic lateral-torsional buckling of stepped beams subjected to uniformly distributed load and end moments. A three-dimensional finite-element program ABAQUS (2007) and a regression program MINITAB(2006) were used to analytically develop new design equation for singly and doubly stepped beams with simple boundary condition. The flanges of the smaller cross-section in the stepped beams were fixed at 30.48 by 2.54 cm, whereas the width and thickness of the flanges of the larger cross-section varied. The web thickness and height of the beams were kept at 1.65 cm and 88.9 cm, respectively. The ratios of the flange thickness, flange width, and stepped length of beam are considered with analytical parameters. Two groups of 27 cases and 36 cases, respectively, were analyzed for doubly and singly stepped beams in the inelastic buckling range. The combined effects of residual stresses and geometrical imperfection on inelastic lateral-torsional buckling of beams are considered. The distributions of residual stress of the cross-section is same as shown in Pi and Trahair (1995) and the initial geometric imperfection of the beam is set by central displacement equal to 0.1% of the unbraced length of beam. The comparisons between results from proposed equations and the results from finite element analyses were presented in this paper. The maximum differences of two results are of 13% for the doubly stepped beam and 10% for the singly stepped beam. The proposed equations definitely improve current design methods for the inelastic lateral-torsional buckling problem and increase efficiency in building and bridge design.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.1
• /
• pp.123-134
• /
• 2019

This paper proposed a new design equation for the inelastic lateral torsional buckling (LTB) of singly symmetric stepped I-beams with non-compact flange sections. The proposed equation was generated using a finite element program, ABAQUS, and a statistical program, MINITAB. The parameters used were the stepped beams parameters; ${\alpha}$, ${\beta}$, and ${\gamma}$ and the length-to-height ratio ($L_b/h$) of the beam. The proposed equation was further validated by means of experimental test, where beams were subjected to four-point bending and supported by roller and lateral braces near the end supports. In addition, finite element models were simulated using the same parameters used in the experimental test to verify the results of the test conducted. It was proved that LTB capacity calculated from the proposed equation is accurate and conservative in comparison with the yielded values from the FEM and actual test, making it a reliable and safe approach in calculating the buckling capacities of singly symmetric stepped beams with non-compact flange sections.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.464-467
• /
• 2011

본 논문에서는 기존에 수행된 비탄성 영역 내 비지지 길이가 존재하고 균일단면을 가지는 I형 보의 좌굴 강도에 대한 해석적 이론적 연구를 토대로 변단면 I형보의 하중고 효과를 고려한 비탄성 횡-비틀림 좌굴강도에 대한 연구를 수행하였다. 유한요소해석에는 4절점 쉘요소인 S4R요소가 사용되었고, 플랜지 길이방향 비, 너비방향 비, 두께의 비로 스텝보를 나타내었으며, 집중하중을 작용시켰다. 개발된 좌굴강도 제안식은(오정재 등, 2011)과 해석결과를 하중고 효과 평가 시 큰 단면변화를 보이는 경우를 제외하고는 ${\pm}10%$의 오차범위를 나타내었다. 본 연구 결과는 다양한 형식의 I형보가 사용되는 빌딩 및 교량의 경제적이고 합리적인 설계의 근간을 제공해 줄 것이며, 향후 비탄성 횡-비틀림 좌굴강도에 대한 연구에도 많은 도움이 될 것이다.

• Proceedings of the KAIS Fall Conference
• /
• 2008.11a
• /
• pp.105-108
• /
• 2008

본 연구에서는 기존에 수행된 균일단면을 가지는 I형 보의 좌굴 강도에 대한 해석적?이론적 연구를 토대로 일축대칭을 이루는 변단면 I형보의 좌굴강도를 산정하고자 범용구조해석프로그램 ABAQUS (2007)를 이용하여 유한요소해석을 실시하였다. 유한요소해석에는 4절점 쉘요소인 S4R이 사용되었고, 플랜지 길이방향 비, 너비방향 비, 두께의 비로 일축대칭 스텝보를 사용하였으며, 균일모멘트를 작용시켰다. 개발된 좌굴강도 제안식은 해석결과와 비교하여 -11%~2%의 오차범위를 나타내었다. 본 연구결과는 다양한 형식의 일축대칭 I형보가 사용되는 빌딩 및 교량 구조물의 경제적이고 합리적인 설계에 활용 될 수 있을 것이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3495-3501
• /
• 2013

The cross-sections of continuous multi-span beams are sometimes suddenly increased or stepped at the interior supports of continuous beams to resist high negative moments. This paper investigates inelastic lateral-torsional buckling of monosymmetric stepped I-beams subjected to pure bending. A three-dimensional finite-element program ABAQUS and a regression program were used to analytically develop new design equation. The flange thickness ratio, flange width ratio and stepped length ratio were considered as parameters of this study. The combined effects of residual stresses and geometric imperfection on inelastic lateral-torsional buckling of beams are considered. The proposed solution can be easily used to calculation for inelastic lateral torsional buckling strengths of monosymmetric beams with doubly stepped cross sections and to develop new design equations for inelastic lateral-torsional buckling resistances of stepped beams.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.1
• /
• pp.55-62
• /
• 2016

The least-mean fourth (LMF) algorithm is well known for its fast convergence and low steady-state error especially in non-Gaussian noise environments. Recently, there has been increasing interest in the least mean square (LMS) algorithms with variable step size. It is because the variable step-size LMS algorithms have shown to outperform the conventional fixed step-size LMS in the various situations. In this paper, a variable step-size LMF algorithm is proposed, which adopts an algebraic optimal step size as a variable step size. It is expected that the proposed algorithm also outperforms the conventional fixed step-size LMF. The superiority of the proposed algorithm is confirmed by the simulations in the time invariant and time variant channels.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.2
• /
• pp.7-13
• /
• 2010

Stepped I-beams having increased moment of inertia at one end (singly stepped beam) or both ends (doubly stepped beams) can often be seen in construction of bridges due to material economy and easy fabrication of the section. This paper presents the results of the parametric study of lateral torsional buckling of monosymmetric stepped I-beams with constant depth subjected to uniform moment. Design recommendations were made based on the finite element results of the models having different combinations of monosymmetric ratio, stepped length ratio, flange thickness ratio and flange width ratio. The proposed approximation is acceptable based on the parameters given having mostly conservative results. The proposed equation can be further used to extend the study to different loading conditions.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.738-740
• /
• 2012

최근 변단면 거더의 경제성을 고려하여 장경간 거더 교량과 강골조 구조물에 변단면보의 사용이 증가하고 있으며, 고강도 강의 등장으로 인해 변단면보의 정확한 좌굴 강도의 평가가 매우 중요시 되고 있다. 본 논문에서는 기존에 연구된 탄성 횡-비틀림 좌굴 강도에 관한 연구를 바탕으로하여 별로 비탄성 구간에 비지지 길이가 존재하는 일축대칭 I형 변단면보의 횡-비틀림 좌굴 강도 해석을 실시하였다. 해석에는 유한요소해석프로그램인 ABAQUS(2007)가 사용되었으며, MINITAB(2006)을 이용하여 간편한 설계식을 제안하고 있다. 일단 계단식 단면을 가지는 보에 대하여 고려하였으며, 플랜지 길이 방향 비, 너비방향 비, 두께의 비로 계단식 I형 보를 나타내었다. 집중 하중을 적용시켰으며 비선형 해석을 위해 잔류응력 및 초기변형과 재료비선형을 고려하였다. 본 연구 결과에서 제안된 식은 향후 다양한 하중이 작용하는 비탄성 횡-비틀림 좌굴 강도에 대한 연구에 많은 도움이 될 것이다.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.3
• /
• pp.156-162
• /
• 2018

The LMF (Least Mean Fourth) algorithm is well known for its fast convergence and low steady-state error especially in non-Gaussian noise environments. Recently, there has been increasing interest in the LMS (Least Mean Square) algorithms with self-adjusted step size. It is because the self-adjusted step-size LMS algorithms have shown to outperform the conventional fixed step-size LMS in the various situations. In this paper, a self-adjusted step-size LMF algorithm is proposed, which adopts an averaged gradient based step size as a self-adjusted step size. It is expected that the proposed algorithm also outperforms the conventional fixed step-size LMF. The superiority of the proposed algorithm is confirmed by the simulations in the time invariant and time variant channels.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.2
• /
• pp.69-74
• /
• 2007

In signal processing applications with highly correlated input signals, subband affine projection algorithm and step size controlling is a good solution for improving the slow convergence rate and large computational complexity of LMS-type algorithms. This paper proposes a subband affine projection algorithm using a variable step size. The proposed method achieves fast convergence rate and small steady-state error with a small computational complexity by combining the SAP and step size controlling in a subband structure. Experimental results on highly correlated input signal show that the proposed method is superior to the conventional methods.