• The Journal of the Convergence on Culture Technology
• /
• v.5 no.1
• /
• pp.429-434
• /
• 2019

There are several high technologies applied to the driving cars such as self-driving car and connected car for safe and convenient driving. VANET provides useful information such as route selection and gas price by communicating nearby cars and RSUs. VANET prefers CCN rather than traditional TCP/IP stack because CCN offers inherent multicast communication for sharing traffic information as well as traditional unicast. When all participating node rebroadcasts the Interest packets in a Vehicular CCN, the network may suffer from Broadcast Storm Problem. In order to mitigate the effect of the problem and to improve the Data packet transmission, not all but some selected nodes have to rebroadcast the packet. This paper simulates car movements using SUMO and evaluates data transmission performance using ns-3. According to the simulation results, when some selected nodes rebroadcast the Interest packets, the transmission performance improves 10% to 25% depending on the number of requesting nodes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.143-148
• /
• 2021

A systematic study of Bloch surface wave (BSW), which is created by guided mode resonance (GMR) of dielectric multilayer structures with a grating profile, is presented to analyze the sensing performance of bio-sensors. The effect of structural parameters on optical behavior is evaluated by using Babinet's principle and modal transmission-line theory. The sensitivity of designed bio-sensors is proportional to the grating constant at wavelength spectrum, and inversely proportional to the normal wave vector of incident electromagnetic wave at angular spectrum. Numerical results for two devices with SiO/SiO₂ and TiO₂/SiO₂ multilayer dielectric stacks are presented, showing that BSW can be exploited for the realization of efficient diffraction-based bio-sensors from infrared to visible-band range.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.3
• /
• pp.233-239
• /
• 2013

A 100 W fuel cell system using chemical storage method has been applied for a propulsion system of the SUAV(Small Unmanned Aerial Vehicle). A fuel cell and battery have been combined for both the small/light hydrogen generation control system and the hybrid power supply system. A small hydrogen generation device was implemented to utilize NaBH4 aqueous solution and dead-end type PEMFC system, which were evaluated on the ground and by the flight tests. The system pressurized at a 45kpa stably operates and get higher fuel efficiency. The pressure inside of the hydrogen generation control system was maintained at between 45 kPa and 55 kPa. The 100W fuel cell system satisfies the required weight and power consumption rate as well as the propulsion system, and the fuel cell system performance was demonstrated through flight test.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.201-209
• /
• 2012

The point-based complex event processing handled an instantaneous event by using one time stamp in each event. However, the activity period of the event plays the important role in the field which is the same as the finance, multimedia, medicine, and meteorology. The point-based event is insufficient for expressing the complex temporal relationship in this field. In the application field of the real-time world, the event has the period. The events more than two kinds can be temporally overlapped. In addition, one event can include the other event. The relation about the events of kind of these can not be successive like the point-based event. This thesis designs and implements the method detecting the patterns of the complex event by using the interval-based events. The interval-based events can express the overlapping relation between events. Furthermore, it can include the others. By using the end point of beginning and end point of the termination, the operator of interval-based events shows the interval-based events. It expresses the sequence of the interval-based events and can detect the complex event patterns. This thesis proposes the algorithm using the active instance stack in order to raise efficiency of detection of the complex event patterns. When comprising the event sequence, this thesis applies the window push down technique in order to reduce the number of intermediate results. It raises the utility factor of the running time and memory.

• Journal of KIISE:Computer Systems and Theory
• /
• v.29 no.7
• /
• pp.369-376
• /
• 2002

Although LRU is not adequate for database that has non-uniform reference pattern, it has been adopted in most database systems due to the absence of the proper alternative. We analyze database block reference pattern with the realistic database trace. Based on this analysis, we propose a new cache replacement policy. Trace analysis shows that extremely non-popular blocks take up about 70 % of the entire blocks. The influence of recency on blocks' re-reference likelihood is at first strong due to temporal locality, however, it rapidly decreases and eventually becomes negligible as stack distance increases. Based on this observation, RCB(Reference Characteristic Based) cache replacement policy, which we propose in this paper, classifies the entire blocks into four block groups by blocks' recency and re-reference likelihood, and operates different priority evaluation methods for each block group. RCB policy evicts non-popular blocks more quickly than the others and evaluates the priority of the block by frequency that has not been referenced for a long time. In a trace-driven simulation, RCB delivers a better performance than the existing polices(LRU, 2Q, LRU-K, LRFU). Especially compared to LRU. It reduces miss count by 5~l2.7%. Time complexity of RCB is O(1), which is the same with LRU and 2Q and superior to LRU-K(O(log$_2$N)) and LRFU(O(l) ~ O(log$_2$N)).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.3
• /
• pp.461-467
• /
• 2003

This paper proposes the method of mobility implementation for location searching in the intelligence wireless ATM networks that expand and apply standard broadband signaling capabilities, and analyze the performance based on the numerical algorithm. The existing B-ISDN UNI protocol stack demands the location search mechanism to determine the location of mobile terminal in the wireless ATM networks because it use single protocol through the fixed PTP interface or PTM interface that don't support terminal mobility. The proposed method make possible the dynamic mobility at a part of wireless access by minimizing the signaling load without a falling-off in system performance by using the intelligence network technology according to the expansion of ATM and B-ISDN signaling integration based on the fixed networks. We implemented the performance analysis by MFC modeling based on numerical algorithm, and realized the efficiency of expenses by carrying out the comparative signaling performance evaluation to measure the relative gains of location search service in the intelligence wireless ATM system. The obtained results have the flexibility to operate in the public B-ISDN network environment without a change of existing B-ISDN/ATM NNI signaling reference to support the wireless ATM access system, and can easily expand to correspond to terminal mobility and various multimedia services in the next broadband PCS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.8B
• /
• pp.1105-1114
• /
• 2010

The Proxy Mobile IPv6 (PMIPv6) has been standardized by the IETF NETLMM WG for network-based mobility management. The PMIPv6 can provide IP mobility for Mobile Nodes (MNs) with low handover latency and less wireless resource usage. But, since the PMIPv6 is basically designed for local mobility management, it cannot support directly global mobility management between different PMIPv6 domains. In the PMIPv6, since all traffic is routed through a Local Mobility Anchor (LMA), it causes a long end-to-end delay and triangular routing problem. Therefore, in this paper, we propose a fast network-based global mobility management scheme and route optimization scheme with a new network entity, called Global Mobility Agent (GMA). Numerical analysis and simulation results show that the proposed scheme is able to support global mobility between different public domains with low handover latency and low end-to-end delay, compared with the PMIPv6.

• Journal of KIISE:Computing Practices and Letters
• /
• v.9 no.4
• /
• pp.393-409
• /
• 2003

In this paper, we present a multi-task debugging environment for Qplus-T embedded-system such as internet information appliances. We will propose the structure and functions of a remote multi-task debugging environment supporting environment effective ross-development. And, we are going enhance the communication architecture between the host and target system to provide more efficient cross-development environment. The remote development toolset called Q+Esto consists to several independent support tools: an interactive shell, a remote debugger, a resource monitor, a target manager and a debug agent. Excepting a debug agent, all these support tools reside on the host systems. Using the remote multi-task debugger on the host, the developer can spawn and debug tasks on the target run-time system. It can also be attached to already-running tasks spawned from the application or from interactive shell. Application code can be viewed as C/C++ source, or as assembly-level code. It incorporates a variety of display windows for source, registers, local/global variables, stack frame, memory, event traces and so on. The target manager implements common functions that are shared by Q+Esto tools, e.g., the host-target communication, object file loading, and management of target-resident host tool´s memory pool and target system´s symbol-table, and so on. These functions are called OPEn C APIs and they greatly improve the extensibility of the Q+Esto Toolset. The Q+Esto target manager is responsible for communicating between host and target system. Also, there exist a counterpart on the target system communicating with the host target manager, which is called debug agent. Debug agent is a daemon task on real-time operating systems in the target system. It gets debugging requests from the host tools including debugger via target manager, interprets the requests, executes them and sends the results to the host.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.62-75
• /
• 2007

This paper describes a shaped-beam antenna for increasing the antenna gain of a radiating element. The proposed antenna structure is composed of an exciting element and a multi-layered disk array structure(MDAS). The stack micro-strip patch elements were used as the exciter for effectively radiating the electromagnetic power to the MDAS over the broadband, and finite metallic disk array elements - which give the role of a director for shaping the antenna beam with the high gain - were finitely and periodically layered onto it. The efficient power coupling between the exciter and the MDAS should be carried out in such a way that the proposed antenna has a high gain characteristic. The design parameters of the exciter and the MDAS should be optimized together to meet the required specifications to meet the required specifications. In this study, a shaped-beam antenna with high gain was optimally designed under the operating conditions with a linear polarization and the frequency band of $9.6{\sim}10.4\;GHz$. Two methods constructed using thin dielectric film and dielectric foam materials respectively were also proposed in order to implement the MBAS of the antenna. In particular, through the computer simulation process, the electrical performance variations of the antenna with the MDAS realized by the thin dielectric film materials were shown according to the number of disk array elements in the stack layer. Two kinds of antenna breadboard with the MDAS realized with the thin dielectric film and dielectric foam materials were fabricated, but experimentation was conducted only on the antenna breadboard(Type 1) with the MDAS realized with the thin dielectric film materials according to the number of disk array elements in the stack layer in order to compare it with the electrical performance variations obtained during the simulation. The measured antenna gain performance was found to be in good agreement with the simulated one, and showed the periodicity of the antenna gain variations according to the stack layer number of the disk array elements. The electrical performance of the Type 1 antenna was measured at the center frequency of 10 GHz. As the disk away elements became the ten stacks, a maximum antenna gain of 15.65 dBi was obtained, and the measured return loss was not less than 11.4 dB within the operating band. Therefore, a 5 dB gain improvement of the Type 1 antenna can be obtained by the MDAS that is excited by the stack microstrip patch elements. As the disk array elements became the twelve stacks, the antenna gain of the Type 1 was measured to be 1.35 dB more than the antenna gain of the Type 2 by the outer dielectric ring effect, and the 3 dB beam widths measured from the two antenna breadboards were about $28^{\circ}$ and $36^{\circ}$ respectively.