• 대한조선학회논문집
• /
• 제40권5호
• /
• pp.26-35
• /
• 2003

Propellers operating in a given nonuniform ship wake generate unsteady loads leading to undesirable stern vibration problems. The skew is known to be the most proper and effective geometric parameter to control or reduce the fluctuating forces on the shaft. This paper assumes the skew profile as either a quadratic or a cubic function of the radius and determines the coefficients of the polynomial function by applying the simplex method. The method uses the converted unconstrained algorithm to solve the constrained minimization problem of 6-component shaft excitation forces. The propeller excitation was computed either by applying the two-dimensional gust theory for quick estimation or by the fully three-dimensional unsteady lifting surface theory in time domain for an accurate solution. A sample result demonstrates that the shaft forces can be further reduced through optimization from the original design.

• 한국기계가공학회지
• /
• 제3권2호
• /
• pp.18-24
• /
• 2004

The effect of surface characterization parameters, such as surface roughness, skewness and kurtosis, on sliding friction and wear was studied experimentally. The friction coefficient was examined under the various parameters and sliding speed, normal load and type of lubricant with ball-on-disk type tribo-meter. The surface of the lower skewness in negative or the higher kurtosis between the same arithmetic mean value tends to indicate low friction.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.439-440
• /
• 2008

A high-speed DCO is proposed that uses the negative-skewed delay scheme. The DCO consists of a ring of inverters with each PMOS transistor driven from the output of 3 earlier stage through a set of minimum-sized pass-transistors. The digitization of negative-skewed delay is achieved by selecting pass-transistors turned on and digitizing the gate voltages of the selected pass-transistors. The proposed 7-stage DCO has been simulated using 1.8V, $0.18\;{\mu}m$ TSMC CMOS process to obtain a resolution of 3ps and an operation range of 2.88-5.03GHz.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.207-212
• /
• 2003

Recently there has been a remarkable increase in the number of high speed and large ships, and the high power involved for propulsion of above ships have brought high pitch ratio and high skew propeller. The recent tendency toward highly skewed propeller has increased the load on propeller blades and the fatigue strength of propeller blades has become the critical point in design of propellers for above ships. In this paper fatigue tests in sea water were carried out on propeller material of Ni-Al bronze. The stress and environmental conditions of the test were selected to be close to those of full size propellers in use. The effect of stress ratio, stress frequency, revolution number of propeller for above ships numbers and so on were discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.752-753
• /
• 2008

The analytical expressions for magnetic field distributions considering slotting effects, cogging torque and back-emf considering skew effects are established. On the basis of magnetic field solutions, electrical parameters such as back-emf constant and winding inductance are obtained. The predicted results are validated extensively by non-linear finite element (FE) analyses. In particular, test results such as back-emf, cogging torque, inductance and resistance measurements are given to confirm the analyses. Finally, generating performances are investigated by applying estimated parameters to equivalent circuit (EC) of the permanent magnet generator (PMG) and validated extensively by FE calculations and measurements.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.30-32
• /
• 2002

선형동기전동기는 고추력, 고정밀 운전을 요하는 시스템에 많이 사용되고 있는데, 추력 증가에 따른 추력 리플의 증가는 고정밀 위치제어에 어려움을 주기도 한다. 철심형 선형동기전동기에서는 자석 배열과 철심 치형상의 상호 관계에 의해 발생하는 디텐트력의 영향이 매우 크므로 이를 저감하기 위한 철심 구조의 설계가 필요하다. 본 논문에서는 실제 제작성을 고려하여 치와 철심부의 챔퍼링, 길이 변경, 자석 배열의 스큐 적용 등을 통해 선형동기전동기의 디텐트력을 저감하기위한 설계법을 제시하고 그 효과를 시험기의 제작 및 실험을 통해 증명하였다.

• 한국자기학회지
• /
• 제6권5호
• /
• pp.287-293
• /
• 1996

농형유도전동기의 회전자는 제조 과정중에 회전자 도체의 단선, 기포 발생으로 인한 회전자 도체의 저항 증가, 스큐 불량 등 여러 가지 고장이 발생될 수 있다. 이와 같은 고장은 유도전동기의 성능을 저하시키므로 회전자를 조립하기 전에 고장 유무를판단하면 조립에 드는 제조 비용을 절약할 수 있고 전동기의 신뢰성을 높일 수 있다. 본 논문에서는 이와같은 고장을 진단하는 방법의 하나로 유한요소법을 이용하여 회전자가 회전할 때 발생하는 전자석 코일에서의 유도 전류 파형을 검출하여 고장을 진단하는 방법을 제안하였다. 제안한 방법의 타당성을 검층하기 위하여 5 Hp 삼상 농형유도전동기에 대해 고장전류를 검출하고 이를 해석 결과와 비교 분석하였다.

• 전기학회논문지
• /
• 제59권7호
• /
• pp.1332-1339
• /
• 2010

This paper presents a large signal analysis of ring-type oscillators with feed forward and negative skewed delay scheme. The analysis yields the frequency increase factor due to two schemes. The large signal analysis is needed, because small signal model is limited to the initial stage of oscillation[1]. For verification of the frequency increase factor, simulation were done under the same conditions for the two different types of ring oscillators, i.e., with and without feed forward and negative skewed delay scheme. Simulation results are in good agreement with predictions based on analysis.

• 대한전기학회논문지
• /
• 제40권7호
• /
• pp.643-655
• /
• 1991

The analysis method on air gap permeance distribution, air gap MMF distribution, air gap flux density distribution, cogging torque and BEMF about the skewed stator slots or the skewed rotor magnet segments for BLDCM, respectively, is studied as a function of the skew ratio. The proposed method describes the differences between the skewed stator slots and teh skewed rotor magnet segments for the air gap permeance distribution, air gap MMF distribution and air gap flux density distribution. The reliability of the method is also confirmed by the waveform of the cogging torque and BEMF through experiments. And the result shows that the effects on the cogging torque and BEMF due to the skewed stator slots or the skewed rotor magnet segments are the same. In case of the skewed stator slots, the effects of the variations of the winding resistance and inductance are also studied.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권3호
• /
• pp.123-130
• /
• 2006

This paper presents characteristics analysis of skewed Synchronous Reluctance Motor using equivalent magnetic circuit and compares with the result of Finite Element Method. Torque ripple must be reduced, because it is producing noise and vibration. There is many kinds of method to reduce torque ripple, but generally we apply skewing stator or rotor. The 2D Finite Element Method(FEM) or 3D FEM is used to analyze the motor, since skew influence the average torque in the motor. However, the FEM takes much time in spite of the advanced computer and numerical technique. This paper will analyze characteristics of skewed synchronous reluctance motor using equivalent magnetic circuit.