• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1187-1190
• /
• 2009

CURVE SQUEAL NOISE IS THE INTENSE HIGH FREQUENCY TONAL THAT CAN OCCUR WHEN A RAILWAY VEHICLE TRAVERSES A CURVE OR A SWITCH. THE HIGH NOISE LEVEL CAUSES ANNOYANCE FOR PEOPLE WHO LIVE IN THE NEIGHBOURHOOD OF THE SQUEALING RAILWAY TRACK AS WELL AS FOR THE PASSENGERS IN CARS WITH CURVES. THIS PAPER EXAMINES THE SPECTRAL SOUND DISTRIBUTION IN CURVES FOR KTX TRAIN. THE FREQUENCY RANGE IS FROM AROUND 4,000 TO ALMOST 16,000Hz, WITH NOISE LEVELS UP TO 92dB IN CURVE R400.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.627-632
• /
• 2003

Squeal noise is generated by railway vehicles transversing tight curves. This squeal has always been noticed as one of the most disturbing noise sourecs of railway systems. At present we cannot predicted squeal noise that is influenced by a large number of dependent parameters. But the application of wheel damping and rail lubrication have successfully reduced wheel squeal. In this study, we measured squeal noise to find out the reduction effectiveness of noise through rail lubricator.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.66-71
• /
• 2002

Squeal noise is generated by railway vehicles transversing tight curves. This squeal has always been noticed as one of the most disturbing noise sources of railway systems. At present we cannot predicted squeal noise that is influenced by a large number of dependent parameters. In this study, we performed structural analysis to find out the frequency of the wheel and also measured squeal noise at Seoul subway line 1, line 2, line 4 for domestic EMU(Electrical Multiple Unit).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.126-134
• /
• 2007

Although there has been substantial research on the squeal noise for the automotive brake system, robust design issues with respect to control factors equivalent to design variables in optimization, noise factors due to system uncertainties, and signal factors designed to accommodate a user-adjustable setting still need to be addressed. For the purpose, the robust design applied to the disk brake system has been investigated by DOE (Design of Experiments) based Taguchi analysis with dynamic characteristics. The specific goal of this methodology is to identify a design with linear signal-response relationship, and variability minimization. The finite element models of the disk brake assembly have been constructed, and the squeal noise problems have been solved by complex eigenvalue analysis. As the practical robust design to reduce the brake squeal noise, material properties of pad, disk, and backplate, thickness and geometry of pad are selected as control factors, material properties of pad and disk, and the contact stiffness have been considered as noise factors, and friction coefficient between pad and disk is chosen as a signal factor. Through the DOE based robust design, the signal-to-noise ratio and the sensitivity for each orthogonal array experiment have been analyzed. Also, it has been proved that the proposed robust design is effective and adequate to reduce the brake squeal noise.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.60-68
• /
• 2010

In this study, the conventional plane tip, double squealer tip, and various groove tip blades were tested in a linear cascade in order to measure the effect of the tip shapes on tip surface heat transfer coefficient distributions. Detailed heat transfer coefficient distributions were measured using a hue-detection based transient liquid crystals technique. Two tip gap clearances of 1.5% and 2.3% of blade span were investigated and the Reynolds number based on cascade exit velocity and chord length was $2.48{\times}10^5$. Results showed that the overall heat transfer coefficients on the tip surface with various grooved tips were lower than those with plane tip blade. The overall heat transfer coefficient on grooved along suction side tip was lower than that on the squealer tip.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.6
• /
• pp.19-25
• /
• 2013

The effect of tip gap height on heat/mass transfer characteristics on the floor of cavity squealer tip has been investigated in a turbine cascade for power generation by employing the naphthalene sublimation technique. The squealer rim height is chosen to be an optimal one of $h_{st}/c$ = 5.51% for the tip gap height-to-chord ratios of h/c = 1.0, 2.0, 3.0 and 4.0%. The results show that heat transfer on the cavity floor is strongly dependent upon the behavior of the cavity flow falling down onto the floor. For lower h/c, the floor heat transfer is influenced by the tip leakage flow falling down along the inner face of the suction-side squealer, whereas the floor heat transfer for higher h/c is augmented mainly due to the impingement of leakage flow on the floor near the leading edge. Compared to the plane tip surface heat transfer, the cavity floor heat transfer is less influenced by h/c. For h/c = 1.0%, the average thermal load is as low as a half of the plane tip surface one, and the difference in the thermal load between the two cases tends to decrease with increasing h/c.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.311-318
• /
• 2010

In this study, the conventional plane tip, double squealer tip, and various groove tip blades were tested in a linear cascade in order to measure the effect of the tip shapes on tip surface heat transfer coefficient distributions. Detailed heat transfer coefficient distributions were measured using a hue-detection based transient liquid crystals technique. Two tip gap clearances of 1.5% and 2.3% of blade span were investigated and the Reynolds number based on cascade exit velocity and chord length was $2.48{\times}10^5$. Results showed that the overall heat transfer coefficients on the tip surface with various grooved tips were lower than those with plane tip blade. The overall heat transfer coefficient on grooved along suction side tip was lower than that on the squealer tip.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.41-47
• /
• 2005

This paper deals with a squeal noise in a brake system. It has been proved that the squeal noise is influenced by the angular misalignment of a disk, disk run-out, with the previously experimental study. In this study, a cause of the noise is examined by using FE analysis program(SAMCEF) and numerical analyses with a derived analytical equation of the disk based on the experimental results. The FE analyses and numerical results show that the squeal noise is due to the disk run-out as the experimental results and the frequency component of the noise equals to that of a disk's bending mode arising from the Hopf bifurcation.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2928-2933
• /
• 2011

The urban railway has been planned not only the subway, but also the elevated railway in Seoul, South Korea. Therefore, it is steadily increasing civil complaints for railway noise passing through that residential district. In this paper, we focused on noise of squeal characteristics induced by interaction between railway vehicle's wheel and rail. Then we selected the point that carried out scattering water droplet to the rail and compared the noise level of the watering test results before and after. Scattering water test results showed that level of the noise reduced intermittently occurring high frequency characteristics of squeal noise as well as overall noise level. In the future, we will apply the sensor to the sprinkling system for noise reduction where the place of existing squeal noise is, and make a suggestion of this solution will be more economical, environmental-friendly, and appropriate to reduce the squeal noise occurred by railway vehicle than others.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.362-367
• /
• 2010

This paper deals with the correlation between the interior noise and the floor vibration of the train from rolling, impulse and friction in Busan Metro line 3. The correlation is verified by sound and vibration measurement causing friction between the railway and the wheel. If ANC(Active Noise Control) system can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 1.8-4.8 dB in squeal noise. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.