• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.465-467
• /
• 2014

본 논문에서는 전기자동차 충전기용 스마트 분전반과 그 제어방법을 제안한다. 제안한 시스템은 평상시에 완속충전기에 전력을 공급하고, 충전요금이 저렴한 경부하시간대에는 스마트 분전반 내의 배터리에 전력을 충전한다. 하지만 완속충전기가 연결된 전원선 중 어느 한 상의 전력소비가 상대적으로 커지거나 피크부하 시 또는 정전 시에는 배터리로부터 전력을 계통에 공급한다. 이렇게 하면 계통으로부터 공급받는 전력량이 감소되어 피크부하 값이 저감될 뿐만 아니라 전원설비의 이용률과 전력품질이 개선되는 이점이 있다. 본 논문에서는 시뮬레이션을 수행하여 제안한 시스템의 유용성을 확인한다.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.124-125
• /
• 2011

현재 지능형 빌딩시스템에 도입되어 있는 스마트 분전반은 스마트 그리드 시스템과 연계하여 전력 수요를 분산시키는 기능 등 다양한 기능을 갖는다. 하지만 예측 불가능한 부하 종류와 운전 패턴에 따른 부하 불평형에 의해 발생하는 전력품질 저하, 전력기기 오작동 등에 능동적인 대처는 역부족이다. 따라서 본 논문에서는 지능형 분전반 운용 알고리즘을 통한 부하관리 시스템을 제안하여 부하 불평형에 따른 피해를 최소화하고자 한다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.1
• /
• pp.109-114
• /
• 2017

In this study, we have developed the active leakage current detection module based on a MSP430 processor, 16bit signal processor. This module can be operated in a desired trip threshold within 0.03 seconds as specified in KS C 4613. This developed module is expected to be applicable as a module for prevention of electric shock in smart distribution panel of smart grid.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.615-620
• /
• 2017

In this study, we have developed the resistive leakage current detecting and tripping circuit breaker based on a 32bit ARM processor. The developed leakage circuit breaker can be operated in a desired trip threshold within 0.03 seconds as specified in KS C 4613. This resistive leakage current breaker is expected to be applicable as a circuit breake for prevention of electric fires and electric shock in smart distribution panel.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.511-521
• /
• 2014

This study proposes an electric vehicle (EV) smart panel board and its control method on the basis of charging scheduling. The proposed system consists of batteries, a three-phase battery charger, three single-phase inverters, transfer switches for electric power distribution, and a controller. The three-phase battery charger usually charges the batteries at midnight when electric rates are cheap and in light load. When the electric power consumption of the EV standard chargers connected to one phase of the power line is relatively large or when a blackout occurs, the electric power stored in the battery is supplied by discharging through the inverters to the EV standard chargers. As a result, the value of peak load and the charging electric power quantity supplied from a utility grid are reduced, and the current unbalance is improved. The usefulness of the proposed system is confirmed through simulations, experiments, and case studies.

• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.15-20
• /
• 2017

This study presented the strength of the materials and parts for smart distribution board fabrication, and developed a work operation process chart for smart distribution board fabrication. This work operation process chart for smart distribution board fabrication complied with SPS-KEMC regulations, and the applicable range and object are less than 1,000 V and 1,000 Hz for the AC distribution board and less than 1,500 V for the DC distribution board. The power supply is 3 phase 4 wires ($3{\Phi}$ 4W), divided into a single phase circuit and a 3 phase circuit. In addition, the circuit was configured so that the leakage current flowing through the distribution line of the load could be monitored in real time by using the sensor module installed at the rear end of the circuit breaker. Therefore, the administrator can easily find the risk factor of the load since engineer can check the leakage current of each distribution line. In addition, if a leakage current greater than standard value flows, it is possible to generate an alarm against a short circuit and cut off the leakage current. The work operation process chart for the smart distribution board fabrication consists of the following steps: raw and subsidiary materials, sheet metal work, tube making, welding, painting, busbar fabrication, assembly and wiring, product inspection, shipment, etc. Moreover, symbols, ${\Delta}$, ${\nabla}$, ${\bigcirc}$, ${\Rightarrow}$, etc. were used according to the type of work and work progress so that workers can easily understand the progress of the work.