• Journal of the Korean Association of Geographic Information Studies
• /
• v.27 no.2
• /
• pp.61-77
• /
• 2024

The purpose of this study was to develop a method for rapidly diagnosing urban thermal comfort using Unmanned Aerial Vehicle (UAV) based data. The research was conducted at Changwon National University's College of Engineering site and Yongji Park, both located in Changwon, Gyeongsangnam-do. Baseline data were collected using field measurements and UAVs. Specifically, the study calculated field measurement-based thermal comfort indices PET and UTCI, and used UAVs to create and analyze vegetation index (NDVI), sky view factor (SVF), and land surface temperature (LST) images. The results showed that UAV-predicted PET and UTCI had high correlations of 0.662 and 0.721, respectively, within a 1% significance level. The explanatory power of the prediction model was 43.8% for PET and 52.6% for UTCI, with RMSE values of 6.32℃ for PET and 3.16℃ for UTCI, indicating that UTCI is more suitable for UAV-based thermal comfort evaluation. The developed method offers significant time-saving advantages over traditional approaches and can be utilized for real-time urban thermal comfort assessment and mitigation planning

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1000-1007
• /
• 2007

In this study, structural vibration analyses of a smart unmanned aerial vehicle (UAV) have been conducted considering dynamic hub-loads of tilt rotor. Practical computational structural dynamics technique based on the finite element method is applied using MSC/NASTRAN. The present UAV(TR-S5-04) finite element model is constructed as a full three-dimensional configuration with different fuel conditions and tilting angles for helicopter, transient and airplane flight modes. In addition, the 3-dimensional supporting equipment structures of electronic devices are considered for vibration analysis. As the results of this study, transient structural displacements and accelerations are presented in detail. Moreover, vibration characteristics of structural parts and installed equipments are investigated for different fuel conditions and tilting angles.

• Smart Media Journal
• /
• v.7 no.4
• /
• pp.44-51
• /
• 2018

The purpose of this research is to collect atmospheric environmental information at specific altitudes in a range of 0 to 1 km above the surface and to monitor it using drones. The corresponding temperature and humidity were measured with the meteorological factors, and the amounts of fine dust and $CO_2$ were observed by the environmental factors so that they could receive the normal values. Monitoring the status of atmospheric gas emission in specific enterprises, industrial complexes and regions through the measurement is meant to help establish policies to reduce pollution factors. In conventional means previously practiced, exhaust gas detection accompanies a great deal of risks in terms of safety because the surveyor is directly exposed to the source of contamination such as the holes installed in the chimney. However, in our proposed method, the drone can collect information in a wide range under safe circumstances, which can be utilized through wide industrial areas.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.430-432
• /
• 2016

It seems that the hottest UAV drone market shows a similar move to that of smartphone. Depart from a communication medium, smartphone incorporates the role of cameras and game players. Likewise, drone will be versatile in the future. For example, drone was developed as war weapons but now it is getting close to our real life as toy or tool for aerial photography. In this paper, we studied how to bring the aging population to drone industry. Previously, controlling skills and taking aerial photography seemed to have nothing to do with citizen seniors. However, we try to show any positive relationship between those, thus creating more job opportunities in this paper.

• Korean Journal of Remote Sensing
• /
• v.32 no.3
• /
• pp.275-285
• /
• 2016

This study analyzes the accuracy of ortho imagery based on whether camera calibration performed or not, using an unmanned aerial vehicle which equipped smart camera. Photgrammetric UAV system application was developed and smart camera performed image triangulation, and then created image as ortho imagery. Image triangulation was performed depending on whether interior orientation (IO) parameters were considered or not, which determined at the camera calibration phase. As a result of the camera calibration, RMS error appeared 0.57 pixel, which is more accurate compared to the result of the previous study using non-metric camera. When IO parameters were considered in static experiment, the triangulation resulted in 2 pixel or less (RMSE), which is at least 200 % higher than when IO parameters were not considered. After generate ortho imagery, the accuracy is 89% higher when camera calibration are considered than when they are not considered. Therefore, smart camera has high potential to use as a payload for UAV system and is expected to be equipped on the current UAV system to function directly or indirectly.

• Journal of Aerospace System Engineering
• /
• v.13 no.2
• /
• pp.43-50
• /
• 2019

Satellite and aircraft components are greatly affected by the possibility for missions and safety due to temperature effects. In the field of fuel cells, research is actively carried out for UAV. For the efficiency and stability of the fuel cells, the temperature for operations must be confirmed. In this paper, a smart paint was fabricated with $BaTiO_3$ and $SrTiO_3$ ceramics in order to take advantage of the rapid characteristics of the PTC thermistor, which is the resistance changes abruptly above the Curie point. A coating agent was prepared to prevent the paint from peeling off the samples and the coated models were checked for resistance changes. Moreover, the resistance change of the $BaTiO_3$ and $SrTiO_3$ with temperature conditions was measured before and after coating.

• Journal of Advanced Navigation Technology
• /
• v.27 no.4
• /
• pp.382-390
• /
• 2023

The Korea market for LUAV (Light Unmanned Aerial Vehicle) weighing less than 150 kg is growing rapidly. As a result, the market for manufacturing and operating LUAV is expanding, and domestic development of parts and finished products is actively taking place. However, the flight control system and onboard software, which are key components of domestic LUAV, are largely dependent on overseas products due to the excessive cost and period required for development. This paper presented a domestic software development and certification procedure using DO-178C, a guideline for aircraft software development, and the Model-based Development method, and conducted a survey of those involved in the development, manufacturing, and certification of LUAV and analyzed the results. In addition, a case study was conducted to apply the software development plan to the helicopter FCC (Flight Control Computer).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.1
• /
• pp.53-60
• /
• 2017

This paper is to design and implement the drone that supports a wideband multimedia communication and a long-range to save people in maritime. The drone is an Unnamed Aerial Vehicle (UAV) that is controlled by a radio wave not by people boarding the machine. We use the drone to respond quickly to the boating accident. To develop a smart drone for the high speed seamless video streaming in a long-range maritime, a necessary techniques are hardware design techniques that design structure of a drone, controlling techniques that operate a drone and communication techniques that control a drone in a long distance. In this paper, the limitations and techniques to design and implement the structure of drone supporting wideband multimedia communication for long-range maritime are explained. By expanding this communication drone network, it is aimed at improving utility of a drone.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.11
• /
• pp.2181-2186
• /
• 2016

Recently, the drone industry rapidly rises to the surface as the new market leading the future, and it seems that the hot UAV drone market shows the similar trend to that of the smartphone. It is expected that the individual application of the drone is quickly diffused as the smartphone roles of camera and game player with the communication medium. For example, the drone is developed mainly as war weapons, but now it is getting close to our real life as the toy or tool for the aerial photography. In this paper, we studied the education for how to bring the aging population to the drone industry. Previously, the controlling skill and taking aerial photography seemed to have nothing to do with citizen seniors. However, we develop the education for try to show any positive relationship between those, in this paper, thus creating more job opportunities for them.

• Korean Journal of Remote Sensing
• /
• v.36 no.6_1
• /
• pp.1349-1365
• /
• 2020

In recent years, in the fields of smart cities and digital twins, research on model generation is increasing due to the advantage of acquiring actual 3D coordinates by using point clouds. In addition, there is an increasing demand for a solid model that can easily modify the shape and texture of the building. In this paper, we propose a method to create a clustered solid building model based on point cloud data. The proposed method consists of five steps. Accordingly, in this paper, we propose a method to create a clustered solid building model based on point cloud data. The proposed method consists of five steps. In the first step, the ground points were removed through the planarity analysis of the point cloud. In the second step, building area was extracted from the ground removed point cloud. In the third step, detailed structural area of the buildings was extracted. In the fourth step, the shape of 3D building models with 3D coordinate information added to the extracted area was created. In the last step, a 3D building solid model was created by giving texture to the building model shape. In order to verify the proposed method, we experimented using point clouds extracted from unmanned aerial vehicle images using commercial software. As a result, 3D building shapes with a position error of about 1m compared to the point cloud was created for all buildings with a certain height or higher. In addition, it was confirmed that 3D models on which texturing was performed having a resolution of less than twice the resolution of the original image was generated.