• Journal of Korean Society for Geospatial Information Science
• /
• v.15 no.2 s.40
• /
• pp.15-23
• /
• 2007

This paper presents a shoreline change analysis on a reclaimed land, using a pair of aerial photographs taken before and after the reclamation. Shorelines that are defined by a tide datum, i.e. Approximately Highest High Water Level, were mapped by both analytical and digital photogrammetric methods. The past shorelines were overlapped with digital cadastral map from which areas of retracted and protruded lands were computed. Magnitude of shoreline changes was estimated by calculating areas between the past and present shorelines. Comparisons in terms of areas showed a fairly good agreement between the two methods. However, particularly in the estuary of complex morphology, shoreline mapping by digital photogrammetric method requires images to be scanned at a resolution higher than 1200 dpi.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.5
• /
• pp.397-405
• /
• 2015

Currently, Korea's digital maps are being produced through traditional aerial photogrammetry methods. Aerial photogrammetry is the most economical way to produce a map of a wide area. However, timely survey is not allowed depends on weather condition and it is inefficient for small area surveying in economic point of view. Therefore, it costs too much and needs long time to produce a map for various small areas where are terrestrial changes for updating the map. In contrast, UAV photogrammetry is possible to work even in cloudy weather because of shooting at low altitude below the clouds. It also has excellent mobility and shoot quickly and well suited for small-scale mapping in several places by low cost. In this study, we produced an ortho-photo and digital map with the UAV photogrammetry method using SIFT and SfM algorithm and verified its accuracy to evaluate the applicability for future digital map updates. The accuracy was verified by comparing the results of the ground survey for check points selected on the digital map. Test results show small errors at ±2.6cm in X coordinates, ±2.8cm in Y coordinates and ±5.8cm in height and we could find a possibility that UAV photogrammetry would be fully applicable for digital map updating.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.1
• /
• pp.123-130
• /
• 2006

The purpose of the paper is to make the three dimensional road simulation model based on the digital photogrammetry and GIS techniques in the middle of Halla mountain of Jeju island. To do this, we generate DEM (digital elevation model) and digital ortho image using GIS tools such as Arc View, Imagestation and MGE module. In GIS, the overlay map schemes combining of the hill shade, the land slope and aspect were applied. Based on the processes, we can build the best three dimensional road line along the hill side of the island. From the results, we also found that the derived DEM from digital ortho image and the GIS technique were very useful for choosing the best three dimensional road design before the real road construction works in Jeju island.

• Journal of Korean Society for Geospatial Information Science
• /
• v.2 no.1 s.3
• /
• pp.73-80
• /
• 1994

Most terrain information have been generally acquired by map. Because the map presents the real terrain, not by real figure but by contours, geometric figures, symbols, texts, and colors, it is not easy to interpret the real terrain by map. For this reason, aerial photos or terrestrial photos also have been used sometimes in the terrain analysis. But photos have geometrical displacement caused by the position of camera at the exposition time and the relief of the object. So, for accurate posional analysis, orthophoto maps produced by optical rectifier have been used. But, it is hard to produce orthophoto map by optical rectifier and the process is so slow. This study aims to present an accurate and rapid method to produce orthophoto map by generating digital elevation model from stereo aerial photos on common computer using the digital photogrammetric technique and producing orthophoto map digitally using the digital elevation model.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.2
• /
• pp.99-105
• /
• 2007

This research is about applying aerial photos to three-dimensional simulation of road design. Instead of existing road design approach using digital map, which inexactly represent some part of topography and landmarks, digital aerial photos are applied to three-dimensional road design to address such inexactness of the map. First of all, ortho-photos are made using aerial photos, and a digital elevation model is created by extracting DEM. Then, by applying the coordinates practically using in planar design to three-dimensional approach, this model will be much helpful in the analyses of road route and viewscape. In addition, through the use of Virtual GIS, many evaluation factors such as urban design, flora, soil, water channel or road shape, flood plan are used for examination, and the effectiveness of applying three-dimensional simulation based on such route design standard is to be reviewed. In this paper, a basic research about three-dimensional design of structures is performed, and through the three-dimensional design, some effective determination to decision-making was carried out. Hereafter, it appears some research regarding environment-friendly construction and design should be followed.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.35 no.3
• /
• pp.155-166
• /
• 2017

As the utilization of aerial images increases, a variety of software using unmanned aerial photogrammetric procedures as well as traditional aerial photogrammetric procedures are being provided. Previously, software that used the unmanned aerial photogrammetric procedure was used for images captured in small areas. Recently, however, software that uses unmanned aerial photogrammetric procedures for large-scale images taken by using aerial photogrammetric cameras has appeared. Therefore, this study generated ortho-images using aerial photogrammetry and unmanned aerial photogrammetry for large aerial images, and compared the features of both procedures through qualitative and quantitative comparisons. Experiments in the study area show that using the 3D mesh effectively removes the relief displacement of the building rather than using the digital surface model to generate ortho-images.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2002.04a
• /
• pp.67-75
• /
• 2002

Digital photogrammetry is one of the powerful tools for surveying in more perceptual ways and exploiting the continuously developing computer technology. Nowadays, digital photogrammetry is being used for a number of industrial measurements and inspections but the automation aspect of this technique is not fully developed yet. Photogrammetric work, which is obtained through usual workflow, delays for a big amount of CGP surveying, interpretation and cadastral information. Therefore through studying ways of reducing the volume of photogrammetric works, financial opportunities for digital photogrammetry can be found. This research is focused on the development of the new workflow and study algorithm in digital photogrammetry. Using this result we can reduce financial expenses and improve technologies of topographic and cadastral plans creation.

• Journal of Korean Society for Geospatial Information Science
• /
• v.13 no.3 s.33
• /
• pp.59-67
• /
• 2005

Building information is primary source in many applications such as mapping, telecommunication, car navigation and virtual city modeling. While aerial CCD images which are captured by passive sensor(digital camera) provide horizontal positioning in high accuracy, it is far difficult to process them in automatic fashion due to their inherent properties such as perspective projection and occlusion. On the other hand, LIDAR system offers 3D information about each surface rapidly and accurately in the form of irregularly distributed point clouds. Contrary to the optical images, it is much difficult to obtain semantic information such as building boundary and object segmentation. Photogrammetry and LIDAR have their own major advantages and drawbacks for reconstructing earth surfaces. The purpose of this investigation is to automatically obtain spatial information of 3D buildings by fusing LIDAR data with aerial CCD image. The experimental results show that most of the complex buildings are efficiently extracted by the proposed method and signalize that fusing LIDAR data and aerial CCD image improves feasibility of the automatic detection and extraction of buildings in automatic fashion.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.3 no.2
• /
• pp.24-36
• /
• 2000

This study deals with the optimal method of orthophoto products using the non-photogrammetric scanners. we scanned positive film of aerial photographs at the different resolution and producted the orthophoto using the automatically generated DEM based on the Digital Photogrammetric Workstation, considering aerial image resolutions, DEM interval, resampling method and outpixel size. As a results, the acquired accuracy was worse in horizontal, but good in vertical. So It will be expected that orthophoto using non-photo grammetric scanner is good enough for the acquisition of GIS data and the calculation of soil volumes.

• Journal of Korean Society for Geospatial Information Science
• /
• v.11 no.1 s.24
• /
• pp.51-59
• /
• 2003

This study intended to extract the spatial data and attribute data from the images of terrestrial and aerial photographs and to compile the digital map from the images using various kinds of photogrammetric analysis. The Three Dimensional Frame Model (3DFM) was produced from multiple images of terrestial photographs, and the Three Dimensional Photo Image Model (3DPIM) was made using 3DFM and image patches of terrestrial photo, which is useful for identifying the feature and characteristics of the object. In addition, the spatial data base for the buildings, roads and supplementary facilities in the objective area was updated by the vectorizing procedures with small scale areal photos.