• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.297-300
• /
• 2010

본 논문에서는 일반적인 해석, 시공단계를 고려한 해석, 시공단계와 장기거동을 고려한 해석의 3가지 해석방법을 사용하여 수평부재의 설계에 적합한 해석방법을 제안하였다. 80층의 2D 구조모델에 3가지 해석방법을 적용하여 각 해석방법에 따라 부등축소량, 수직부재에 작용하는 축력, 수평부재의 단부에 작용하는 내력의 해석결과를 얻어 비교하였다. 또한 부재의 내부에서 철근과 콘크리트의 하중분담율의 시간에 따른 변화양상을 알아보았다. 해석결과 시공단계에 의한 영향은 수평부재에 작용하는 축력과 부등축소량 예측, 부재 내력 해석에 있어서 반드시 고려되어야 함을 알 수 있었다. 장기거동의 효과는 기둥축소에는 크게 영향을 미치지만 수직부재의 축력, 수평부재의 내력에는 변형만큼의 영향은 보이지 않는다. 시공시의 보정량을 결정하기 위해서는 장기거동이 반드시 고려되어야 하지만 부재의 단면설계의 목적으로는 제외되어도 무방할 것으로 판단된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.4
• /
• pp.395-401
• /
• 2010

The vertical members of structures are shortened as time goes on. Because structures have been high-rising and atypical there should be different axial loads among vertical members and it causes differential column shortenings. The differential column shortening add stresses to connections, make slab tilt, and damage to non-structural components. To reduce these influences compensation is need. The rational compensation means the exact expectation of amounts of column shortenings and the reasonable corrections. The expectation of column shortenings are more exact as researched, however, there is little research about the compensation. This paper presents the average correction method and the constraints for differential column shortenings considering errors due to the construction precision. The relations between constraints and the number of correction groups give an objective criterion for decision of constraints.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.588-591
• /
• 2010

건물의 수직부재는 시공 후 시간이 지남에 따라 수축하게 된다. 이러한 현상을 기둥축소 현상이라고 부르며 원인으로는 탄성, 비탄성, 환경적 요인 등 여러 가지가 있다. 각 수직 부재에 걸리는 하중의 종류와 크기, 그리고 처한 환경 등이 다르므로 부재별로 축소량에 차이가 있게 된다. 이로 인하여 건물은 여러 가지 피해를 입게 된다. 이에 따라 수직부재인 기둥과 전단벽의 축소량을 예측하는 연구가 활발히 진행되고 있다. 그러나 예측된 축소량을 보정하는 기법에 관한 연구는 그리 많지 않다. 따라서 본 논문에서는 선행 연구되었던 기존의 부등 축소량 보정 기법의 한계에 대하여 지적하고 새로운 보정기법인 평균을 이용한 부등축소량 보정기법을 제시하였다. 본 논문에서 제시한 보정기법의 효용성을 입증하기 위하여 같은 예제에 대하여 기존의 방법과 본 논문에서 제시한 방법을 이용한 결과들을 비교, 정리하였다.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.2
• /
• pp.249-259
• /
• 2011

In this study, the distortional behaviors of tub-section steel girders subjected to torsional loading were analyzed, and predictor equations were developed for estimating the member forces induced in the internal bracing system installed in the steel tub girders. Torsional loadings originated either by eccentric vertical loading or girder curvature were decomposed into the pure torsional force component that does not affect the distortional box deformation, and into the distortional force component that directly induces box distortion. The axial member forces induced in the internal cross frames were formulated as a function of the magnitude of torsional loading through the analytical investigation of the interactions between the distortional force component and internal cross frames. To verify the proposed equations, three-dimensional finite element analysis (3D FEA) was conducted for the straight simple-span girder and the three-span continuous girder samples. Very good agreement was found between the member forces from the FEA and the proposed equations.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.173-174
• /
• 2009

With the recent emergence of high rise buildings, this study was conducted in order to examine shortening, which has been used only in civil engineering structures, in such buildings. Examination of the shortening of vertical members is basically focused on deformations caused by load applied to concrete, material characteristics, etc. Shortening is analyzed through calculating parameters from the factors or characteristics of concrete, but analysis in the aspect of material tests has been somewhat unsatisfactory. Thus, this study purposed to analyze basic material test items for correcting the shortening of vertical members, namely, columns, to determine the reliability of material tests before parameter calculation for correcting shortening, and to examine the performance of material tests.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.6
• /
• pp.637-644
• /
• 2021

Dynamic response of structures can be evaluated experimentally by conducting cyclic loading tests. It has been known that steel materials are rate-dependent and the lateral response of a structure is significantly affected by the presence of axial force. However, the rate-dependency of steel column structures subjected to both axial and lateral loads has not been sufficiently studied yet due to the difficulty of controlling the axial force in a real-time manner during test. This study introduces an advanced way to apply the axial load in real-time to a column specimen using the adaptive time series (ATS) compensator and the flexible loading beam (FLB), where the H-shape steel columns made of SS275 are used for monotonic and cyclic loading tests with various loading rates with axial loads. The lateral strength and post-yield response of the steel columns are compared for each of monotonic and cyclic loading tests. The estimating equation of yield stress of various strain rate has proposed and finite element analysis were performed for comparison.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.259-262
• /
• 2010

최근 건물형상의 다양화로 인하여 수직부재의 불규칙성이 빈번하게 발생하면서 전통적인 보-기둥 형식의 골조에서 변형된 보와 기둥의 특징을 공유하고 있는 경사기둥의 사용빈도가 높아지고 있다. 현재 국내에서 사용하고 있는 내진설계방법은 강도에 근거를 둔 설계법으로서 구조물이 탄성상태에서 저항해야 하는 부재력에 근거하고 있다. 그러나 기준에서 규정하고 있는 또는 그 이상의 지진하중이 구조물에 가해지는 경우에 구조물은 비선형 거동을 하게 되는데 구조물이 비선형 거동을 할 때에는 탄성상태와는 다른 힘의 흐름을 나타내게 된다. 본 논문에서는 12층 철골 모멘트 골조 구조물에 대하여 횡력에 저항하는 정형화된 골조와 경사기둥을 이용한 골조의 내진성능 및 비선형 거동을 조사하였다. 그 결과 강기둥-약보로 설계된 정형화된 구조물에서는 보의 소성힌지가 계속적으로 발달하면서 구조물이 저항하는데 반하여 경사기둥을 가진 구조물은 비탄성 상태에서 경사기둥에 인접한 기둥부재로 하중이 집중되면서 정형골조에 비하여 붕괴 메카니즘이 훨씬 작은 변위에서 발생하는 것을 볼 수 있었다.

• Journal of Korean Association for Spatial Structures
• /
• v.9 no.1
• /
• pp.69-78
• /
• 2009

Recent earthquake, such as the Northridge(1994), the Kobe(1995) and the Izmit(1990) earthquakes, gave serious damage in various buildings and bridges by the vertical seismic component. Most of the seismic designs neglect the vertical seismic component for usual frame structures. The purpose of this study is to evaluate the effects of the vertical seismic component and to compare the axial force of columns and plastic rotation angle of the analytical models in these effects. The vertical seismic component produced a large increment of axial force in columns. And the vertical seismic component caused a significant increase of the damage in the columns. As analysis result, increase of axial force cause the damage of columns and give possibility of story collapse mechanism of the structure system. Therefore, area that near fault ground motion is expected may be consider the effect of vertical component of seismic ground motions.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.5
• /
• pp.140-148
• /
• 1994

RCI 318-8!4 recommends that when the specified cornpresslve strength of concrete In a column is greater than 1.4 times thdt spec~f~ed for a floor svsttm. top surface of the colunm concrete shall extend 2ft(600mm) into the slab from the face of colurnn to avoid unexpected brittle failure. Six test specimens were cast arid tested on 2/3 scale frame specmiens havlng different extension distances and compressive strength of concrete as the major variables. The paper discusses the performance of the frames in terms of ductility and also presents the assessment of the ACI 318-89 provisions.The test results showed that the ductility index were incrrased with increasing of compressive strength of concrete and extension distance. And top surface of the column concrete should extend 2h(h overall depth of beam) into the beam from the face of the column to avoid unexpected brittle failure in frame.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.1
• /
• pp.93-102
• /
• 1999

Increased height of buildings causes severe shortening of vertical structural members due to the accumulated axial load. It not only decreases the serviceability of a structure but also affects significantly the stability of a structure itself due to the secondary stress. The main purpose of estimating the shortening of vertical structural members is to compensate the differential shortening of adjacent members. This paper presents the comparison of stresses between the vertical structural members compensated during construction process and these compensated during design process under the seismic load and represents that the precise compensation of vertical structural members is important.