• The Journal of the Acoustical Society of Korea
• /
• v.25 no.5
• /
• pp.246-256
• /
• 2006

The plane wave reflection coefficient is an acoustic property containing all the information concerning the ocean bottom and can be used as an input parameter to various acoustic propagation models. In this paper, we measure the plane wave reflection coefficient, the sound speed, thd the attenuation for saturated granular medium in the water tank. Three kinds of glass beads and natural sand are used as the granular medium. The reflection experiment is performed with the sinusoidal tone bursts of 100 kHz at incident angles from 28 to 53 degrees, and the sound speed and attenuation experiment are performed also with the same signal. From the measured reflection signal, the reflection coefficient is calculated with the self calibration method and the experimental uncertainties are discussed. The sound speed and the attenuation measurements are used for the estimation of the porosity and permeability, the main Biot parameters. The estimated values are compared to the directly measured values and used as input values to the Biot theory in order to calculate the theoretical reflection coefficient. Finally, the reflection coefficient predicted by Biot theory is compared to the measured reflection coefficient and their characteristics are discussed.

• Journal of Wetlands Research
• /
• v.9 no.2
• /
• pp.71-84
• /
• 2007

Masan Bay is a representative semi-closed bay acted as a sedimentation reservoir with a slow current velocity and a poor water circulation in Korea. The pollutants from terrestrial sources into the Masan Bay have apparently environmental pollution problems, such as eutrophication, red tied, and hypoxia. In this study, An ecological modeling work was performed to estimate the material circulation including the growth of bivalve in ecosystem. Furthermore, the effect of water purification was calculated by filter feeding bivalve to particulate organic matter just like COD and phytoplankton. And Water quality management strategy by bio-purification of bivalve is derived through selection of location, quantification of bivalve aquaculture farm. The results showed that the optimum location for bivalve farming is where phytoplankton accumulation by physical processes is maximized and the optimum density and area of bivalve are 35 individuals $m^{-3}$ and ca. 500 hectare, respectively. When assuming conditions for the optimum growth of bivalve, COD could decrease by up to 18% even without other reduction of pollution loads.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.203-203
• /
• 2011

최근 들어 기후변화에 따른 강우패턴이 바뀌고 각종 하천개발이나 토목공사, 농경지, 경작지 등의 객토 등으로 인해 매년 탁수의 발생이 크게 증가하고 있는 추세이다. 특히 여름철 집중강우의 영향에 따라 상류지역 하천에서 발생하는 부유물질은 호수로 유입되어 장기간 체류하며 심각한 오염원으로서 수중생태계에 치명적인 영향을 주고 있다. 또한 하천과 호수의 상류지역의 농경지나 경작지에서 발생된 부유물질에는 과도한 비료의 사용으로 입자표면에 많은 인을 포함하고 있어 호수 수질악화 및 부영양화의 직접적 요인이 되고 있다. 이에 따라 세계 각국에서는 부유물질은 오염원뿐 아니라 생태계에 영향을 주는 인자로서 엄격히 규제하고 있으며, 특히 농업지역이 많은 하천에 대해서는 유역전체를 대상으로 부유물질에 대한 총량관리를 적용하고 있다. 그러나 우리나라의 경우 하천 수질기준 1급수의 부유물질 농도는 25 mg/l 로서 이는 선진국과 유사한 기준이나 실질적으로 규제가 어려운 실정이다. 수환경에서의 부유물질이란 수체 내 존재하는 유기성, 무기성 물질로써 입자 지름이 2mm 이하의 물에 용해되지 않는 물질을 말하는 것으로, 물의 탁도를 유발시키는 원인이 되며 빛을 차단하여 수생태계에 악영향을 초래한다. 국내 132개 하천을 대상으로 부유물질의 농도와 어류의 종 다양성간 상관성을 조사한 결과, 부유물질의 농도가 15 ~ 20 mg/l 이상에서 종 다양도는 1.0 이하로 급감하는 경향을 보였다(최재석 등, 2004). 한편, 대청호는 1975년부터 1980년에 걸쳐 건립된 저수 면적 $72.8km^2$, 저수량 15억톤의 인공호수로 우리나라 3번째 규모의 인공호수이다. 특히, 대전 및 청주지역의 식수는 물론, 생활용수 및 공업용수를 공급하는 중요한 수자원으로서 부유물질에 대한 모니터링 및 관리가 시급하나 저수 용량이 크고 체류시간이 길어 여름철 부영양화가 매년 반복되고 있다. 따라서 본 연구에서는 부유물질의 농도 변화에 따른 분광반사 특성을 조사하고, 이를 대청호의 Landsat 위성영상에 적용하여 대청호 내 부유물질의 농도변화를 추정하였다. 이와 함께 부유물질 농도 변화에 따른 탁수 환경 모니터링에 원격탐사 기법이 효과적임을 제시하고자 하였다.

• Tribology and Lubricants
• /
• v.33 no.6
• /
• pp.245-250
• /
• 2017

In this work, we examine pure water and water with nanoparticles to investigate water lubrication characteristics and the effect of nanoparticles as lubricant additives for different substrates. We test carbon-based coatings and metals such as high-speed steel and stainless steel in pure deionized (DI) water and DI water with nanoparticles. We investigate water lubrication characteristics and the effect of nanoparticles based on the friction coefficient and wear rate for different substrates. The investigation reveals that nanoparticles enhance the friction and wear properties of high-speed steel and stainless steel. The friction coefficient and wear rate of both high-speed steel and stainless steel decreases in DI water with nanoparticles compared with the results in pure DI water. The presence of nanoparticles in water show good lubricating effect at the contact area for both high-speed steel and stainless steel. However, for carbon-based coatings, nanoparticles do not improve friction and wear properties. Rather, the friction coefficient and wear rate increases with an increase in the concentration of nanoparticles in case of water lubrication. Because carbon-based coatings already have good tribological properties in a water environment, nanoparticles in water do not contribute toward improving the friction and wear properties of carbon-based coatings.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.640-644
• /
• 2010

하천, 호소 등에서 공사 시 준설작업으로 인해 고탁수가 발생되며 이러한 탁수의 이송 확산은 수환경에 변화를 초래한다. 탁수는 준설작업 시 커터헤드(cutter head)가 해저면에 닿는 순간부터 작동을 멈출 때까지 계속하여 발생하며, 이러한 과정들이 반복되면서 많은 양의 부유토사가 발생하게 되고 고탁수현상이 일어난다. 이렇게 발생한 탁수는 수체흐름에 따라 이송 및 확산된다. 탁수발생은 수중의 빛 투과를 감소시켜 일차 생산자인 부유성 및 부착조류의 생육을 저해하고, 이들의 생산성 감소와 군집구성의 변화는 수서생태계의 먹이사슬을 통해 이들을 먹이로 하는 저서무척추동물과 어류의 현존량 감소와 종 구성에 영향을 미치고, 고농도의 현탁 입자는 어류 아가미에 염증을 유발하거나 점막의 파괴와 감염을 유발하여 치사시킬 수도 있다. 또한 과도한 부유 입자는 하류로 침강되어 하천 바닥에 서식하는 부착조류, 무척추 동물 및 곤충의 생육에 피해를 주고, 이것은 어류의 먹이에 영향을 미쳐 어류 개체수를 감소시키거나 산란된 물고기 알을 매몰시키거나 질식시키는 등 여러 가지 방법으로 수서생물상에 영향을 미치게 된다.(낙동강수계관리위원회, 2005) 따라서 준설작업에 있어 탁수의 이송 확산범위를 사전에 예측하고 국내 실정과 환경여건에 알맞게 적용되고, 실용화될 수 있는 수치모델링에 대한 기반핵심 기술개발이 필요하다. 현재 낙동강에서 진행되고 있는 준설현장에서 발생하는 부유탁수의 이송 확산과정을 이차원 흐름해석모형인 RAM2 모형과 오염물 이송 확산해석모형인 RAM4 모형을 이용하여 수치해석을 하고 분석함으로써 수치해석에 의한 부유탁수의 이송 확산모의 결과가 환경영향 범위를 예측하는 데에 적용될 수 있는지를 알아보고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.10
• /
• pp.41-48
• /
• 2022

The mass density of the medium (ρ) used to calculate the maximum shear modulus (G_max) of the saturated ground based on the shear wave velocity is unclear. Therefore, to determine the mass density, a verification formula and five scenarios were established. Laboratory tests were conducted, and the obtained results were compared. The mass density of the medium was assumed to be saturated (ρ_sat), wet (ρ_t), dry (ρ_dry), and submerged conditions (ρ_sub), and the V_s ratios of saturated to dry condition were obtained from each case. Assuming the saturated density (ρ_sat), the V_s ratio was consistent with the value from the resonant column test (RCT) results, and the value from the bender element test results was consistent with the wet density assumption (ρ_t). Considering the frequency range of earthquakes, it is concluded that applying the saturated density (ρ_sat) is reasonable as in the RCT results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.8
• /
• pp.682-687
• /
• 2013

Navigation is a crucial capability for all types of manned or unmanned vehicles. However, vehicle navigation in underwater environments still remains a challenging problem since GPS signals for position fixes are not available in the water. Terrain-referenced underwater navigation is an alternative navigation technique that utilizes geometric information of the subsea terrain to correct drift errors due to dead-reckoning or inertial navigation. Terrain-referenced navigation requires the description of an undulating terrain surface as a mathematical function or table, which often leads to a highly nonlinear estimation problem. Recently, PFs (Particle Filters), which do not require any restrictive assumptions about the system dynamics and uncertainty distributions, have been widely used for nonlinear filtering applications. However, PF has considerable computational requirements which used to limit its applicability to problems of relatively low state dimensions. This study proposes the use of a Rao-Blackwellized particle filter that is computationally more efficient than the standard PF for terrain-referenced underwater navigation involving a moderate number of states, and its performance is compared with that of the extended Kalman filter algorithm. The validity and feasibility of the proposed algorithm is demonstrated through numerical simulations.

• Clean Technology
• /
• v.6 no.1
• /
• pp.27-38
• /
• 2000

A physicochemical process called Ultra Rapid Coagulation(URC) can dramatically remove organics, metals, and phosphates in wastewater by adding weighted coagulation additive(WCA) and recycling sludge into the coagulation basin to increase the growth rate and adsorption ability of floc. Also this process can improve floc settling rate than conventional coagulation process and reduce the pollutants loaded into the receiving water for securing water source. It was evaluated that WCA and sludge added have effects on the removal efficiency and estimated the possibilities of reusing the effluent from this process.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.95-101
• /
• 2002

The head-capacity curves for pumps developed by the pump manufacturer are based on tests of a sin91e pump operating in a semi-infinite pool with no nearby walls or floors and no stray currents. Hence, flow into the pump suction is symmetrical with no vortices or swirling. Pump station designers rely on these curves to define the operating conditions for the pump selected. But various constraints such as size, cost, and limitations on storage time require walls, floors, and pump intakes to be close proximity to each other. From this background, the authors are carrying out a systematic study on the flow characteristics of intakes within a sump found within a sump of pump stations. Model pump intake basin is designed and PIV is adopted as a measuring tool to capture the instantaneous flow patterns. Special attention is paid to investigate the flow patterns near the free surface due to different clearances from back-wall to vertical intake pipe with bell mouse and without. Moreover, the locations and vorticities of the various types of vortices that were found in the examinations are discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2250-2255
• /
• 2010

An fine silver particle has a variety of uses, such as in killing micrograms and as catalysts. Many techniques have been used for the production of the fine particles. Faraday cell, consisting of two silver electrodes in an electrolyte, is unique, but it is hard to get a very fine particle by this method. A finer silver nano-particle producing cell, utilizing a dielectric bed as a lower electric current and higher field controlling means, has been proposed and investigated. The I-V characteristics of the cell and effect of the dielectric bed on the producing finer silver nano-particles have been investigated. The I-V characteristics of the cell with the dielectric bed were different from that of the same system without the bed, due to the increased cell resistance and elevated electric field intensity. It is found that the proposed cell with the dielectric bed can produce finer silver nano-particles effectively, which, however, can be used as one of effective fine silver nano-particle producing means.