• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1303-1310
• /
• 2007

In IEEE 802.11b wireless network, stations synchronize themselves to the beacons periodically sent by the access point (AP) when they are running in low power mode. Stations stay awake for enough time to receive beacon because it is delayed in AP if the wireless channel has been being used by other traffic at each scheduled instant. In this paper, we propose a method that measures the delay of received beacons and calculates wake-up interval of station to receive the next one. Beacon transmission delay at the AP is analyzed. The proposed method is simulated and its characteristics are described in the analysis. The result measured in terms of station's wake-up interval shows some enhancement in energy consumption.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1017-1024
• /
• 2002

In this paper, we present the analysis of radio wave propagation characteristics in curved tunnels. Tunnel propagation models are performed in two cases which are using ray-tracing method for straight tunnels and geometrical optics extension to the standard hybrid waveguide model for curved ones. By regression analysis for measured power based on distance between the transmitter and the received antenna in tunnels that have 3.5 m $\times$ 6 m cross section and limited wall depth path loss are 0.19 dB/m for straight section and 0.68 dB/m for curved ones. By comparing model analysis with measurement in tunnels, it has been shown that the simulated results of tunnel propagation models are similar to the measured values.

• Journal of Korea Society of Industrial Information Systems
• /
• v.14 no.1
• /
• pp.9-16
• /
• 2009

In this paper, a method is proposed for the analysis of radiowave receiving characteristics of an ammunition with electric detonator. In this method, an ammunition with electric detonator is modelled as a receiving antenna with its gain obtained by computer simulation or measurement. The induced radiowave power is obtained by inserting the gain of the electric detonator in the antenna coupling formula. Radiowave receiving characteristics at very close distances are obtained by Treasuring the transmission coefficient between a half-wave dipole and the electric detonator model. Radiowave receiving characteristics of the electric detonator in a 105mm tank ammunition are obtained using the proposed method and the safety of the 900 MHz RFID reader on the detonator is assessed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.215-220
• /
• 2012

Recently, one of the research topics is wireless Ad-Hoc network minimizing power consumption because of limited power. We propose optimal power allocation scheme of each transmit node and derive performance analysis of system that recently designed Double opportunistic relay system which fixed branch receiver to use more than efficient power consumption. Optimal power location scheme is shown that outage probability has always better performance than equal power allocation. Furthermore, we are known that outage probability is minimized by increasing average transmit relays to obtain the diversity gain when average channel power gain is less.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.23-28
• /
• 2023

In a wireless smart utility network communication system, an asynchronous low power MAC is standardized and used according to IEEE 802.15.4e. An asynchronous MAC called RIT (Receiver Initiated Transmission) has a characteristic in which delay time and power consumption are greatly affected by a check-in interval (RIT period). By waking up from sleep every check-in interval and checking whether there is data to be received, power consumption in the receiving end can be drastically reduced, but power consumption in the transmitting end occurs due to an excessive wakeup sequence. If an excessive wake-up sequence is reduced by shortening the check interval, power consumption of the receiving end increases due to too frequent wake-up. In the RIT asynchronous MAC technique, power consumption performance according to traffic load and operation of check-in interval is analyzed and applied to Wi-SUN construction.

• Annual Conference of KIPS
• /
• 2012.11a
• /
• pp.1177-1179
• /
• 2012

최근 전력 수요가 지속적으로 증가함에 따라서, 전력 수급을 관리하는 EMS 에 대한 관심이 높아지고 있다. 전력 수급을 안정적으로 관리하기 위해서는 전력 계통의 상태변화에 따라 급전원에게 실시간 알람을 발생시켜주는 알람 시스템이 반드시 필요하다. 그러나 기존 EMS 의 알람 시스템은 알람 인지자의 역할을 고려하지 않고 알람 발생 여부를 알려주고 인지함으로써 보안상의 문제점을 가지고 있다. 본 논문에서는 RBAC 기반의 EMS 알람 시스템을 제안한다. 제안된 시스템을 통해 EMS 의 알람 시스템은 허가된 급전원에게만 알람 발생 여부를 알려주고 알람을 수신한 급전원이 직접 알람을 인지하도록 한다. 또한, 수신한 급전원이 원거리에 위치할 경우, 근거리 급전원에게 알람의 인지를 위임함으로써 알람 시스템의 보안을 강화한다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.3
• /
• pp.67-71
• /
• 2015

In this Paper, we proposed optimization of system performance, power splitting protocols applied to relay in the cooperative communication undergo co-channel interference. When relay adjust power distribution factors undergo co-channel interference, it is possible to optimize and maximize the channel capacity of the receiver. Because of energy haversting, interfence transfer to new power source. If finding the optimal power levels, to solve inability in system, and to increase the efficiency of the network. Finally, performance of the proposed protocol is analyzed in terms of outage probability, capacity of system.

• Journal of Digital Convergence
• /
• v.17 no.10
• /
• pp.243-249
• /
• 2019

In this paper, we have developed a device to reduce the standby power consumption that is unnecessarily consumed in unused electrical appliances. The Doppler sensor is used to automatically power off and power off the outlet depending on whether or not a person is present near the outlet. The Doppler sensor uses a coaxial cable trap to design a transmitting antenna and emits a 10 GHz band RF signal and receives a reflected wave signal whose wavelength is reflected from the target object to the receiver to detect an object and recognize human approach. It automatically cuts off and restores standby power to prevent unnecessary power consumption, saving energy and developing a standby power automatic shutdown and recovery device that can prevent the risk of large fires caused by leakage current.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.244-250
• /
• 2012

This paper describes a 4-Gb/s receiver circuit for a low-swing ground-referenced differential signaling system. The receiver employs a common-gate level-shifter and a continuous linear equalizer which compensates inter-symbol-interference (ISI) and improves voltage and timing margins. A bias circuit maintains the bias current of the level-shifter when the common level of the input signal changes. The receiver is implemented with a low-power 65-nm CMOS technology. When 4-Gb/s 400mVp-p signals are transmitted to the receiver through the channel with the attenuation of -19.7dB, the timing margin based on bit error rate (BER) of $10^{-11}$ is 0.48UI and the power consumption is as low as 0.30mW/Gb/s.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.2
• /
• pp.111-116
• /
• 2003

In this paper, a CMOS baseband analog receiver for wireless home network is discussed. It is composed of a Gilbert type mixer, an Elliptic 6th order 1ow pass filter, and a 6-bit A/D converter. The main role of the mixer is generating a mixed analog signal between the 200MHz output signal of CMOS RF stage and the 199MHz local oscillator. After the undesired high frequency component of the mixed signal comes out. Finally, the analog signal is converted into digital code at the 6-bit A/D converter, The proposed receiver is fabricated with 0.25${\mu}{\textrm}{m}$ 1-poly 5-metal CMOS technology, and the chip area is 200${\mu}{\textrm}{m}$ X1400${\mu}{\textrm}{m}$. the receiver consumes 130㎽ at 2.5V power supply.