• KSBB Journal
• /
• v.18 no.2
• /
• pp.111-116
• /
• 2003

Hydrogen producing acidogenic microorganisms were self-immobilized using organic-inorganic hybrid polymer within 5 minutes. During the continuous tratment of synthetic wastewater at a hydraulic retention time of 20 hours, at 37$^{\circ}C$, pH 5.0, the self-immobillized granules were maintained in a stirred tank reactor. The black colored granules gradually became milky. Image analysis showed that the mean diameter of the milky colored granules ranged from 1.5 to 20. mm. The maximum bio-gas procuction rate was 380 ml/L/hy and the concentration of H$_2$was around 50%, while no methane was detected. Granular ECP was extracted and its content was measured to elucidate the role of the organic-inorganic hybrid polymer. Further increases of granule concentration are expected to increase the hydrogen production rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4643-4651
• /
• 2013

In this study, we have surveyed the new technologies in the cryogenic distillation of ITER, equilibrium reactors and helium refrigeration cycle contained in the isotope separation system (ISS). We also have collected thermodynamic and transport properties for $H_2$, HD, $D_2$, HT, DT and $T_2$ components of which properties are not built in a general purpose chemical process simulators such as Aspen Plus and PRO/II with PROVISION. Verification works have been performed to compare between literature data and simulation results. For the simulation of ISS involving six hydrogen isotope components, four distillation columns and two equilibrium reactors are used for the separation of $D_2$ and DT from $T_2$.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.1
• /
• pp.12-16
• /
• 2005

Diesel is one of the best hydrogen systems, which has very high volumetric density $[kg\;H_2/m^3]\;(>100)\;and\;gravimetric\;density[\%\;H_2]\;(>\;15)$Several catalysts were selected for diesel reforming. 3 catalysts of our group (NECS-1, NECS-2, NECS-3) and 2 commercial catalysts (Sud-Chemie, Inc, FCR-HCl4, FCR-HC35) were used to reform diesel. NECS-1 showed the best performance to reform diesel. In addition to these results, we studied on reaction characteristics for better understanding about auto thermal reforming of diesel by investigating product gas concentrations and temperature Profiles along the catalyst bed. We found technological issues such as fuel delivery and thermal configuration between front exothermic part and rear endothermic part.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.96-102
• /
• 2022

Reactants of PEMFC are hydrogen and oxygen in gas phases and fuel cell overpotential could be reduced when reactants are smoothly transported. Numerous studies to modify cathode flow field design have been conducted because oxygen mass transfer in high current density region is dominant voltage loss factor. Among those cathode flow field designs, a block in flow field is used to forced supply reactant gas to porous gas diffusion layer. In this study, the block was installed on a simple fuel cell model. Using computational fluid dynamics (CFD), effects of forced convection due to blocks on a polarization curve and local current density contour were studied when different air flow rates were supplied. The high current density could be achieved even with low air supply rate due to forced convection to a gas diffusion layer and also with multiple blocks in series compared to a single block due to an increase of forced convection effect.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.69-74
• /
• 2015

The study investigated numerically the heat transfer and chemical reaction characteristics of a methane-steam reforming by using a 3-dimensional computational fluid dynamics (CFD) code (Fluent ver. 16.1). The fuel temperature and its species mole fractions were estimated for various Reynolds number in the reformer tube at different burner temperatures. The catalysts were modeled as the porous medium of nicrome in the reformer tube. We considered radiation effect as well as conduction and convective heat transfer because the methane-steam was reformed at very high temperature condition above 1000 K. For two different Reynolds numbers of 49,000 and 88,000 and the burner temperatures were in the range from 1,100 K to 1,300 K. At a low Reynolds number, the fuel temperature increased, leading to increase in hydrogen reforming. However, fuel temperature and hydrogen reforming decreased because of higher convective heat transfer from relatively low fuel temperature. Moreover, the hydrogen reforming also increased with burner temperature.

• Membrane Journal
• /
• v.23 no.4
• /
• pp.290-296
• /
• 2013

Poly(vinylidenefluoride-co-chlorotrifluoroethylene) P(VDF-co-CTFE) polymer was attached to methacrylic acid (MAA) in the presence of 1,8-diazabicyclo[5,4,0]undec-7-ene(DBU) catalyst to prepare P(VDF-co-CTFE)-MAA copolymer. The modified P(VDF-co-CTFE)-MAA was polymerized with 2-sulfoethyl methacrylate (SEMA) monomer in the presence of 4',4'-azobis(4-cyanovaleric acid(ACVA) initiator by free radical polymerization to form the proton conducting membrane. The ratio of the SEMA was increased in the membrane to increase the presence of the acidic group. The maximum IEC value that was observed at 50% SEMA was around 0.82 meq/g, which is consistent with the water uptake value. The highest proton conductivity achieved by P(VDF-co-CTFE)-MAA/SEMA membrane with 50% SEMA was approximately 0.041 S/cm. This indicates that the available ionic group for the proton conduction increases with the increase in the SEMA in the membrane.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.2
• /
• pp.170-177
• /
• 2019

Continuous solid circulation test at high temperature and high pressure conditions and batch type reduction-oxidation tests were performed to check feasibility of a 0.5 MWth chemical looping combustion system. Pressure drop profiles were maintained stable during continuous solid circulation up to 16 hours. Therefore, we could conclude that the solid circulation between an air reactor and a fuel reactor could be smooth and stable. The measured fuel conversion and $CO_2$ selectivity were high enough even at high capacity and even after cyclic tests. Therefore, we could expect high reactivity of oxygen carrier at real operation condition.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.4
• /
• pp.412-420
• /
• 2016

Effect of $H_2S$ on reactivity of oxygen carrier was measured and discussed using fluidized bed reactor and SDN70 oxygen carrier. We could get 100% of fuel conversion and $CO_2$ selectivity even though $H_2S$ containing simulated syngas was used as fuel for reduction. Absorbed sulfur was released during oxidation and $N_2$ purge step after oxidation as $SO_2$ form. We could get 100% of fuel conversion and $CO_2$ selectivity during cyclic reduction-oxidation tests up to 10th cycle. However, only 6~7% of sulfur can be removed during oxidation and $N_2$ purge step and 93~94% of sulfur was accumulated in the oxygen carrier. Therefore we could conclude that total removal of sulfur was not possible. $SO_2$ emission during oxidation decreased as the number of cycle increased. Therefore we could expect that the reactivity of oxygen carrier will be decreased with time.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.109-109
• /
• 2017

알지네이트 하이드로 젤은 해조류에서 추출되는 천연 고분자인 알지네이트가 칼슘 또는 마그네슘 양이온과 이온가교(Ioninc cross linking)를 형성할 때 알지네이트의 고분자 구조가 칼슘, 마그네슘 양이온을 감싸면서 형성되는 고분자이다. 알지네이트 하이드로 젤은 높은 생체적합성(Biocompatibility)으로 인해 세포 재생을 위한 조직공학 및 재생의학, 약물전달 등의 제약 관련 분야에 광범위하게 적용될 수 있는 물질로 많은 연구가 이루어지고 있다. 본 연구에서는 마이크로 플루이딕 칩을 이용하여 알지네이트 튜브를 제조하였다. 먼저 유동 포커싱 방식(flow focussing)을 유도할 수 있는 PDMS(Polydimethylsiloxane) 마이크로 플루이딕 칩을 제조하였다. 마이크로 플루이딕 칩은 CNC(Computer Numeric Control) milling machine을 이용한 template를 만들고 NOA mold를 이용하여 최종 PDMS 칩을 제작하였다. 튜브를 만들기 위한 마이크로 채널은 내부 채널 ($200{\times}200um$), 중간 채널 ($200{\times}200um$) 및 외부 채널 ($200{\times}200um$)로 구성되며 내부, 중간, 외부의 유체가 합류하는 수집채널은 폭 500 um, 깊이 200 um로 구성되었다. 운반체로는 5%의 acetic acid를 함유한 mineral oil를 이용하였으며 내부의 core flow는 $H_2O$로 하였다. 중간 유체인 2% 알지네이트 프리폴리머는 칼슘 이온의 존재 하에서 젤화 과정이 매우 빠르기 때문에 마이크로 채널 내부에서의 반응을 제어하고 막힘을 방지하기 위해 수용성 복합 칼슘-에틸렌 디아민 테트라 아세트산 (EDTA)을 사용하였다. 본 마이크로 플루이딕 칩에 각각의 유체를 이동시켰을 때, 운반체인 oil phase의 수소이온은 중간 유체인 알지네이트 프리폴리머와의 계면을 통해 확산되어 Ca-EDTA 복합체로부터 칼슘 양이온의 방출을 유발하게 된다. 방출된 칼슘 양이온은 알지네이트 고분자와의 이온 가교를 통해 알지네이트 하이드로 젤을 형성하여, 각 유체의 flow에 따라 알지네이트 튜브를 쉽고 빠르게 제조 가능하였다. 본 연구에서 제조된 알지네이트 튜브는 인체 내 장기간 약물 전달을 위한 나노섬유로 활용하거나 인공혈관을 구성하는 extracellular matrix로 활용될 잠재력을 가지고 있어 추후 활발한 연구개발이 진행될 예정이다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.554-560
• /
• 2017

Reduction reactivity of new oxygen carriers for chemical looping combustion system were investigated using $CH_4$ as a reduction gas in a bubbling fluidized bed reactor and compared with that of former SDN70 oxygen carrier. New oxygen carriers showed good reduction reactivity at different $CH_4$ concentration. N018-R2 particle represented better reactivity than SDN70 at high $CH_4$ concentration. N018-R2 particle showed higher fuel conversion and $CO_2$ selectivity than those of SDN70 particle within the temperature range of $750-900^{\circ}C$. Moreover, attrition loss of N018-R2 particle was almost same with that of SDN70 particle. Consequently, we could select N018-R2 particle as the best oxygen carrier.