• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3006-3013
• /
• 2015

Flat tube heat exchangers can improve the thermal performance significantly compared with round tube heat exchangers. For proper design of flat tube heat exchangers, one should know the tubeside heat transfer coefficients. In this study, convective boiling heat transfer coefficients of R-410A were obtained in a flat extruded aluminum tube with $D_h=1.41mm$. The test range covered mass flux from 200 to $600kg/m^2s$, heat flux from 5 to $15kW/m^2$ and saturation temperature from $5^{\circ}C$ to $15^{\circ}C$. The heat transfer coefficient curve shows a decreasing trend after a certain quality(critical quality). The critical quality decreases as the heat flux increases, and as the mass flux decreases. The early dryout at a high heat flux results in a unique 'cross-over' of the heat transfer coefficient curves. The heat transfer coefficient increases as the mass flux increases. At a low quality region, however, the effect of mass flux is not prominent. The heat transfer coefficient increases as the saturation temperature increases. The effect of saturation temperature, however, diminishes as the heat flux decreases. Both the Shah and the Kaew-On et al. correlations reasonably predicted the present data.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.2
• /
• pp.67-76
• /
• 2006

For a hydro power plant project, the headrace tunnel having a finished diameter of 3.3 m was constructed in volcanic rocks with well-developed vertical joint and high groundwater table. The intake facility was located 20.3km upstream of the powerhouse and headrace tunnel of 20km in length and penstock of 440m in height connected the intake and the powerhouse. The typical caldera lake, Lake Toba set the geology at the site the caving of the ground caused tension cracks in the vertical direction to be developed and initial stresses at the ground to be released. High groundwater table(the maximum head of 20bar) in the area of well-connected vertical joints delayed the progress of tunnel excavation severely due to the excessive inflow of groundwater. The excavation of tunnel was made using open-shield type TBM and mucking cars on the rail. High volume of water inflowraised the water level inside tunnel to 70cm, 17% of tunnel diameter (3.9m) and hindered the mucking of spoil under water. To improve the productivity, several adjustments such as modification of TBM and mucking cars and increase in the number of submersible pumps were made forthe excavation of severe water inflow zone. Since the ground condition encountered during excavation turned out to be much worse, it was decided to adopt PC segment lining instead of RC lining. Besides, depending on the conditions of the water inflow, rock mass condition and internal water pressure, one of the invert PC segment lining with in-situ RC lining, RC lining and steel lining was applied to meet the site specific condition. With the adoption of PC segment lining, modification of TBM and other improvement, the excavation of the tunnel under severe groundwater condition was successfully completed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.750-756
• /
• 2011

An experimental study was carried out to measure the heat transfer coefficient in flow boiling to deionized water in a microchannel having a hydraulic diameter of $500{\mu}m$. Tests were performed in the ranges of heat fluxes from 100 to 400 kW/$m^2$, vapor qualities from 0 to 0.2 and mass fluxes of 200, 400 and 600 kg/$m^2s$. From the experimental results, it is found that the measured heat transfer coefficients is independent of mass flux and quality, and is somewhat dependent of heat flux. Measured data of heat transfer are compared to a few available correlations proposed for macroscale. The previous correlations for macroscale overpredicted the flow boiling heat transfer coefficient for the test conditions considered in this work.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.139-146
• /
• 2014

Sodium borohydride ($NaBH_4$) is considered as a secure metal hydride for hydrogen storage and supply. In this study, the interfacial friction of two-phase flow in the dehydrogenation of aqueous $NaBH_4$ solution in a microchannel with a hydraulic diameter of $461{\mu}m$ is investigated for designing a dehydrogenation chemical reactor flow passage. Because hydrogen gas is generated by the hydrolysis of $NaBH_4$ in the presence of a ruthenium catalyst, two different flow phases (aqueous $NaBH_4$ solution and hydrogen gas) exist in the channel. For experimental studies, a microchannel was fabricated on a silicon wafer substrate, and 100-nm ruthenium catalyst was deposited on three sides of the channel surface. A bubbly flow pattern was observed. The experimental results indicate that the two-phase multiplier increases linearly with the void fraction, which depends on the initial concentration, reaction rate, and flow residence time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.451-451
• /
• 2013

현재 세계적으로 에너지 공급원의 다변화가 시급한 실정이며 그 후보로 태양에너지, 풍력 및 수력에너지와 같은 신재생 에너지에 대한 연구분야가 부각되고 있다. 전체 에너지 중 신재생 에너지의 비중은 빠르게 증가되고 있으며, 그 중에서도 태양광에너지의 분야가 가장 활발히 연구되고 있다. 특히, III-V족 화합물 반도체 태양전지는 직접 천이형 밴드갭을 가지고 있어 기존 실리콘 태양전지에 비해 광 흡수율이 높은 장점을 가지고 있다. 따라서 본 연구에서는 Molecular Beam Epitaxy (MBE)장치를 이용하여 성장온도에 따른 p-n접합 GaAs 태양전지 구조를 제작하여, 광전변환 효율과 결함구조 관련성을 조사하였다. 먼저 Si이 $1{\times}10^{18}cm^{-3}$으로 도핑된 n형 GaAs기판위에 성장온도 $480^{\circ}C$와 $590^{\circ}C$에서 Be을 $5{\times}10^{18}cm^{-3}$ 도핑한 p 형 GaAs를 200 nm 두께로 각각 성장하여, 2개의 p-n 접합 GaAs 태양전지 구조를 제작하였다. 시료의 전기적 특성과 결함상태는 Capacitance-Voltage (C-V) 와 Deep Level Transient Spectroscopy (DLTS)를 사용하여 조사하였다. DLTS 측정을 위해 p-형의 GaAs박막 위에 Au(300 nm)/Pt(30 nm)/Ti(30 nm)를 e-beam evaporator로 증착한 후, 직경 $300{\mu}m$의 메사 에칭으로 p-n접합 다이오드 구조를 제작하였다. 본 연구를 통해 GaAs p-n접합구조 성장온도에 따른 광전변환 효율과 결함상태와의 물리적인 연관성을 논의할 것이다.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.83-89
• /
• 2000

This paper presents a pressure drop correlation for evaporation and condensation of alternative refrigerant with oil in micro-fin tubes. The correlation was developed from a data base consisting of oil-free pure and mixed refrigerants in micro-fin tube; Rl25 R134a. R32 R410a(R32/R125 50/50% mass), R22, R407c(R32/R125/R134a, 23/25/52% mass) and R32/R134a(25/75% mass). The micro-fin tube used in this paper had 60 0.2mm high fins with a 18 helix angle. The cross sectional flow area $(A_c)$ was $60.8 mm^2$ giving an equivalent smooth diameter$(D_e)$ of 8.8mm. The hydraulic diameter $(D_h)$ was estimated to the 5.45mm. The new correlation was obtained by replacing the friction factor and the tube-diameter in Bo Pierre correlation by a friction factor derived from pressure drop data for a micro-fin tube and the hydraulic diameter, respectively. This correlation was also used to predict some pressure data with a lubricant after using a mixing viscosity rule of lubricants and refrigerants. As a result, the new correlation was also well predicted to the measured data within a mean deviation of 19.0%.

• Tunnel and Underground Space
• /
• v.9 no.1
• /
• pp.20-26
• /
• 1999

The completion of the Bakun Diversion Tunnel is subsequently to the Main Dam construction. Therefore, the completion date is very important for the Bakun Hydroelectric Project. Generally, the tunnel lining work as a finishing phase of the tunnelling project occupies a important portion as well as an excavation and a support work of the tunnels in respect to the construction cost and period. Internal section of Bakun Diversion Tunnel is designed circular shape to reduce the roughness of the water flow with 12 meters in diameter of total length 4314.6 meters of 3 tunnels. The lining thickness is varied between 500 mm and 700 mm depending on the structural condition. From the original Tender design of the Bakun tunnels, the required quantity of steel bars was 5,985 ton designed by Reinforced Concrete (RC) through the entire tunnel linings. During the detail design stage by the consideration of the rock conditions and various load conditions, we could suggest five kinds of RC lining type including plain concrete lining type. Through the detail design modification, we could reduce the required amount of steel bars to 2,178 ton, as a half of original Bill of Quantity. Finally, this design modification give us the time and cost saving effect to catch up the construction progress in time.

• Journal of Energy Engineering
• /
• v.28 no.3
• /
• pp.26-33
• /
• 2019

A comparison of CL 13% and 17% IBLOCA counterpart tests(CPTs) between the ATLAS and LSTF facilities was carried out and the behavior of peak cladding temperatures(PCTs) and related thermal hydraulic phenomena were investigated and discussed. There appeared quite a big difference in PCT behavior between the two CPTs and a further comparison of reactor coolant system design between the two facilities was performed. As a result, there was a difference in fuel alignment plate (FAP) design, e.g., one FAP in ATLAS, a combination of upper core plate and upper end box in LSTF, respectively. The FAP design mainly affects the reflux condensate behavior in IBLOCA tests and any difference in FAP design can be a possible reason for different PCT behavior between the two facilities. It should be a further study to find the reason of different PCT behvior between the two facilites.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.55-61
• /
• 2022

There is a major interest in diagnostic technology for multiple cancers worldwide. In order to reduce the difficulty of cancer diagnosis, a liquid biopsy technology based on a microfluidic device using trace amounts of biofluids such as blood is being studied. And optical biosensing, which measures the concentration of analytes through fluorescence imaging using biofluids, requires various strategies to improve sensitivity, and specialists and equipment are needed to carry out these strategies. This leads to an increase in diagnostic and production costs, and it is necessary to develop a technology to solve this problem. In this paper, we design and propose a fluorescent multi-cancer diagnostic sensing platform structure that implements passive self-separation technology and molecular recognition activation functions by fluid mixing, only with the geometry and microfluidic phenomena of microchannels based on self-driven flow by capillary force. In order to check the parameters affecting the performance of the plasma separation part of the designed sensor, the hydrodynamic diameter of the channel and the viscosity of the fluid were set as variables to confirm the formation of plasma separation flow through simulation. And finally, we propose an optimal sensor platform structure.

• Journal of Korean Society of Forest Science
• /
• v.87 no.1
• /
• pp.90-97
• /
• 1998

This study was carried out to compare the characteristics of relative conductivity(RC) in the twenty-one deciduous broad-leaved species. The results obtained were summarized as follows : 1. The RC ranged from $3.18{\times}10^{-15}$ to $1.23{\times}10^{-10}m^2$ in deciduous broad-leaved species, and appeared different values in various portions of a tree and species. 2. In eight diffuse-porous species, the ranges of average RC were $3.49{\times}10^{-13}$ to $6.35{\times}10^{-11}m^2$ in stems. $4.89{\times}10^{-13}$ to $2.99{\times}10^{-11}m^2$ in branches, and $1.33{\times}10^{-13}$ to $9.42{\times}10^{-12}m^2$ in junction part between stem and branch. In thirteen ring-porous species, the RCs were $7.14{\times}10^{-13}$ to $4.76{\times}10^{-11}m^2$ in stems, $2.93{\times}10^{-13}$ to $3.91{\times}10^{-11}m^2$ in branches, and $1.14{\times}10^{-13}$ to $9.20{\times}10^{-12}m^2$ in junction part. 3. The RC and diameter of stem have no interrelation in eight diffuse-porous species. The RC of stem increased with decreasing diameter of stem in eleven ring-porous species except Fraxinus mandshurica and Maackia amurensis. 4. In five deciduous broad-leaved species, the RC of 1-year-old shoots(the leader and adjacent laterals ) ranged from $4.87{\times}10^{-13}$ to $8.41{\times}10^{-11}m^2$ in the leaders, and $7.93{\times}10^{-14}$ to $2.01{\times}10^{-11}m^2$ in the adjacent laterals. The RCs were much greater in the leaders than in the adjacent laterals because of the hydraulic dominance of the leader shoot.