• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1908-1910
• /
• 1998

지금 까지 유도 가열용 인버터의 여러 가지 회로 방식이 소개 되었다. 그러나, 회로 방식을 선정 하는데 있어서 설계자의 취향, 또는 종래의 회로을 채택으로 인하여, 각기 다른 출력, 스위치 소자의 정격 전압, 전류, 및 수동 소자의 정격 전압, 전류을 만족하는 회로 선정이 될 수 있는 수식적 모델링, 비교 실험이 부족 하였다.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.3
• /
• pp.149-153
• /
• 2007

Perpendicular patterned magnetic media have been regarded as a prime candidate to achieve an ultra-high magnetic recording density of over 1 Tera-bits/$inch^2$. Patterned magnetic media with nanoscale patterns have been fabricated using various nanopatterning technologies. We focused on the two technical issues of nanoinjection molding technology. Firstly, we have investigated a cost-effective method to fabricate metallic stamps. Secondly, we focused on the analysis of nanoinjection molding with passive heating, where the replication of 50 nm nanopillar arrays was successful. The effect of the thermal insulation layer on the replication quality was examined by analytical and experimental methods. Finally, we deposited a magnetic layer on a injection molded nanopillars and measured. Our methodology can provide cost-effective mass-production for patterned magnetic media.

• Fire Science and Engineering
• /
• v.17 no.4
• /
• pp.64-69
• /
• 2003

Low story apartments and housings with manual fire extinguishers are very susceptible to fro damages, when people are absent or there are old and weak peoples. To reduce such fire damages, automatic fire suppression at the early stage is very important, and thus automatic and cost-effec-tiye fire extinguisher was developed. This study revealed that the reaction temperature and response time are greatly influenced by the small thickness variation of the detective parts and heating rates. The influence of the thickness of the detective parts was shown significant when the heating rate was low, The reduction in the thickness could lower the response time to 40seconds.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.253-258
• /
• 2020

Petrochemical industry complex in Korea always has high riskiness due to explosive and inflammable gases. To prevent these explosion, most facility of petrochemical industry complex requires the performance of explosive proof. The control panel, which is used as explosive proof, has been used the air injection method by manually from outside to constantly keep the temperature and pressure between inside and outside of the panel. In this paper, we propose the automatic temperature controller, which performs automatic heating and cooling according to temperature inside the panel in order to control temperature automatically.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.50.3-50.3
• /
• 2009

지구관측용 광학탑재체를 탑재한 저궤도위성은 내부부품보호를 위해 표면처리와 같은 수동적 기법과 히터동작과 같은 능동적 기법을 함께 사용을 한다. 내부열손실을 막기 위해 위성외부의 거의 모든 부분을 단열재(MLI)로 감싸게 되며, 각 단열재는 견고하게 고정이 된다. 광학탑재체는 구성품의 보호와 최적성능의 영상획득을 위해 다수의 히터가 장착되는데, 각 히터는 가열대상물의 온도를 실시간으로 측정하여 미리 설정된 On/Off 온도를 기준으로 제어가 된다. 궤도상에서 탑재체가 겪게 되는 다양한 궤도열환경 시나리오에 대한 열해석결과를 이용하여 히터의 위치, 용량 및 제어온도가 결정된다. 궤도상 운용 중, 위성을 보호하는 단열재 사이에 미세한 틈이 발생한 가상적인 상황을 가정하여, 탑재체 히터의 임무주기변화와 탑재체 운용에의 영향을 분석한다.

• Journal of agriculture & life science
• /
• v.53 no.5
• /
• pp.137-143
• /
• 2019

To manufacturing of solid fuel by reuse of the wastes, the drying unit which have 500 kg/hr of drying capacity was developed and experimentally evaluate the performance. The spinach grown in Nam-hae island were used for the experiments and investigated of the heated-air drying characteristics as the inlet amount of raw materials, raw material stirring status, conveying type and drying time. The drying air heated by the energy derived from the steam which is supplied from the incineration plant. The moisture contents of raw materials were measured 85.65%. The inlet flow rate of drying air made a difference as the depth of the raw materials loaded on the drying unit and temperature has showed 108~144℃. The drying speed of the mixed drying more than doubled as that of non mixed drying under the same drying type, inlet amount, drying time and drying air temperature. In each experiment, the drying capacity have showed over 500 kg/hr. A drying efficiency of the ratio of drying consumption energy to input energy was 33.46%, lower than the average of 57.76% for the 157 conventional dryers. Because developed dryer must have a drying time of less than one hour, it is considered that the dry efficiency has been reduced due to the loss of wind volume during drying. If waste heat from incineration plant is used as a direct heat source, the dry air temperature is expected to be at least 160℃, greatly improving the drying capacity.