• Journal of Welding and Joining
• /
• v.9 no.3
• /
• pp.1-9
• /
• 1991

근래에 들어 국민들의 소득이 높아지고 생활수준이 향상됨에 따라 어려운 일은 하지 않으려고 하는 풍조가 사회전반에 걸쳐 만연되고 있다. 용접공정은 우리사회에서 가장 어렵고, 고된 일종의 하나로 인식되어 있고, 그 중에서도 특히 수도용 대형 강관의 용접시공은 열악한 작업현장 환 경과 전자세 용접등의 어려움 때문에 매우 높은 임금을 제시해도 용접공들사이에서 기피되는 대표적 사례이다. 따라서 앞으로의 원활한 상수도 공급을 위해서 긴급하게 요구되는 대형강관의 설치를 위해서는 용접공정의 자동화가 절실히 요구되는 실정이다. 이와 같은 문제의 해결을 위한 연구의 일환으로 선진국의 수도용 대형 강관 용접시공 방법 및 자동화의 현황을 파악하고, 우리나라의 용접시공 현황과 비교, 검토하여 현실에 적합한 수도용 강관의 용접시공 방법 및 자동화기법을 도출하기 위해서 미국, 이태리, 일본의 관계되는 회사들을 방문하였다. 이와 같은 해외방문목적을 요약하면 아래와 같다. 1) 선진국 대형 강관 용접시공의 현황파악 2) 수도용 대형 강관 용접시공자동화의 가능성 조사. 3) 대형 강관 용접시공 자동화를 위해서 필요한 장치들의 성능조사.

• 수도
• /
• s.38
• /
• pp.25-31
• /
• 1987

• 수도
• /
• s.63
• /
• pp.34-42
• /
• 1993

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2011.11a
• /
• pp.83-86
• /
• 2011

옥내소화전설비, 스프링클러설비 등 수계소화설비에 일반배관용 스테인리스강관과 그 연결에 필요한 이음쇠의 사용가능성을 적용사례, 내식성 등을 통해 확인하였고, 기존 수계소화 설비의 배관에 대한 개선방안을 도출하였다. 일반배관용 스테인리스강관 및 이음쇠는 국내의 경우 수도용으로 활발히 사용되고 있으며, 독일 영국 일본 미국 등의 수계소화설비에 사용되고 있음을 확인할 수 있었다. 강관과 이음쇠의 연결상태에서 내식성을 확인하기 위해 0.5 %와 3.5 %의 소금물을 관내에 주입한 후 28일 보관한 결과 이상이 없음을 확인하였다. 또한, 기존에 설치되어있는 수계소화설비는 배관계의 온도차에 의한 보상방법이 되어있지 않아 작동물질의 열팽창에 따라 강관, 이음쇠의 파손이 발생할 수 있음을 확인하었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.12
• /
• pp.733-740
• /
• 2017

'The facilities standards of water supply' issued by the Ministry of Environment in 2004 indicates that expansion joints cannot be used in welding water supply steel pipes. However, their reason is not clear and it is difficult to confirm the stability of the steel pipe for a water supply pipeline. The purpose of this study is to determine whether or not an expansion joint is necessary to improve the stability of water supply in steel pipe through a displacement analysis of the pipework. The test results are as follows. Firstly, it was found that expansion and contraction of the water supply steel pipe (D 2,400 mm) occur repeatedly in 4 cycles per year, and the maximum expansion and contraction amount of the pipe is 13.03 mm in 1.24 km pipelines. Secondly, the thermal stress caused by expansion and contraction of the steel pipe is $13.7{\sim}36.1kgf/cm^2$ according to the burial depth (0~4 m). The main comparison factors to determine the stability of the steel pipe (STWW 400) were the allowable tensile strength and the fatigue limit, which were computed to be $4,100kgf/cm^2$ and $1,840kgf/cm^2$, respectively. Finally, the thermal stress of the steel pipe is very small compared to the allowable tensile stress and fatigue stress. Therefore, thermal stress does not affect the stability of the steel pipe, although the expansion and contraction of the steel pipe occurs by temperature changes. In conclusion, the study demonstrated that expansion joints are not required in water supply steel pipelines.

• Journal of Welding and Joining
• /
• v.9 no.4
• /
• pp.50-59
• /
• 1991

Large steel water pipes in Korea are joined prevalently by bell end method and welded at inside as well as outside of the pipes with the length of leg which is same as or larger than the thickness of pipes. This results in an excessive consumption of material and labor compared with foreign counturies such as USA, so that in our recent situation of requiring a number of water pipes such consumption is very ineffective and an improvement in weld design of water pipes is urgently necessary. In this experimental study, the possibility of reducing the length of leg to 85% of the pipe thickness was investigated through observations of microstructure and cross section of weldments, the tensile test, and the impact test of the field and laboratory specimens. As the results of this study, it was revealed that water pipes which have the leg of fillet about 0.8xthickness show a good weldability, have a greater strength than the base metal and absorb the enough energy to be safe in the working condition of the pipes.

• Journal of Welding and Joining
• /
• v.10 no.3
• /
• pp.54-62
• /
• 1992

Large steel water pipes are joined prevalently by bell and method and welded at inside and outside of lapped parts. According to the Korean Standard(KS) for fabrication of water pipes, the weldments are designed to have the length of leg which is same as or larger than the thickness of the pipe. It is recently pointed out that the standard size of weldments is too large, which results in an excessive consumption of material and labor. In this study, several cases of weldments having different sizes were investigated to reduce the length of leg to the effective size. For each case, the analysis of stresses was carried out to evaluate the safety of the welded pipes by using a package program, ANSYS, under the consideration of the loading condition of water pipes which includes the soil pressure on the pipe, the load over the road, and temperature change of the pipe. The results of this study revealed that the weldment which has the length of leg of the size over 0.7*thickness of the pipe could provide a stress level below the yield strength. Especially when the length of leg is 85% of the wall thickness, the maximum equivalent stress is only slightly higher than that of the leg of fillet of the size of 1.0*pipe thickness.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.331-338
• /
• 2008

Coal-tar enamel, blown asphalt and polyethylene have been used as wrapping materials of steel pipe in Korea. Currently, every manufacturer produces wrapped steel pipes with different materials and methods, and little research has been performed to get on wrapping methods and materials. In this research, properties of wrapping material of steel pipe used for water supply have been evaluated. All of the materials tested in this work were found to meet the standard. Among the wrapping materials of steel pipe tested, blown asphalt and coal-tar enamel were reasonable in price, and their mechanical properties were excellent. The quality of the wrapped steel pipes was being melted easily in organic solvent. When coated thick, the load of the steel pipes was higher than necessary. Tensile strength of cathode exfoliation and PE 3-layer wrapping method was excellent. The pulling intensity of T-Die PE 3-layer was stronger than PE fluidized in PE wrapping method. Cathode exfoliation area was smaller than PE fluidized. Mechanical property and thermo-property of T-Die PE 3-layer were excellent and its anti-chemical property was great. Liquid epoxy can change the property of coating materials depending on the hardening condition and resin selection. Polyurethane used in this test showed a less adhesive strength with steel pipes than epoxy. Moisture absorbance rate was higher than Epoxy's, however. To utilize polyurethane as wrapping materials, basic property of the matter should be improved followed by finding the best suited coating condition. The method of PE 3-layer by extrude method appeared to be the best in this study. However, identification of other wrapping materials requires further additional tests.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.1
• /
• pp.46-52
• /
• 2024

The structural safety of expansion joints for piping systems has been drawing attention owing to ruptures and leaks of water pipes caused by earthquakes and road subsidence at soft ground. In general, metal bellows are installed as expansion joints to prevent various damages in the piping system. In this study, the seismic performance of a valve chamber system was evaluated by performing earthquake shaking table tests. To validate the benefits to structural safety of metal bellows in connecting steel pipes to valve chambers, the seismic tests were conducted on expansion joints (bellows) and general pipping, and the results were compared for durability. Strain gauges were attached to measure the effects of the input motion. As a result of the shaking table test, it was confirmed that the strain of the valve chamber structure and inflow or outflow steel pipes were decreased in 1/100, 1/20 by applied to the expansion joints.

• MISULJARYO - National Museum of Korea Art Journal
• /
• v.97
• /
• pp.14-54
• /
• 2020

The overall study of Samsaebulhoedo (painting of the Assembly of Buddhas of Three Ages) at Yongjusa Temple has focused on dating it, analyzing the painting style, identifying its painter, and scrutinizing the related documents. However, its greater coherence could be achieved through additional support from empirical evidence and logical consistency. Recent studies on Samsaebulhoedo at Yongjusa Temple that postulate that the painting could have been produced by a monk-painter in the late nineteenth century and that an original version produced in 1790 could have been retouched by a painter in the 1920s using a Western painting style lack such empirical proof and logic. Although King Jeongjo's son was not yet installed as crown prince, the Samsaebulhoedo at Yongjusa Temple contained a conventional written prayer wishing for a long life for the king, queen, and crown prince: "May his majesty the King live long / May her majesty the Queen live long / May his highness the Crown Prince live long" (主上殿下壽萬歲, 王妃殿下壽萬歲, 世子邸下壽萬歲). Later, this phrase was erased using cinnabar and revised to include unusual content in an exceptional order: "May his majesty the King live long / May his highness the King's Affectionate Mother (Jagung) live long / May her majesty the Queen live long / May his highness the Crown Prince live long" (主上殿下壽萬歲, 慈宮邸下壽萬歲, 王妃殿下壽萬歲, 世子邸下壽萬歲). A comprehensive comparison of the formats and contents in written prayers found on late Joseon Buddhist paintings and a careful analysis of royal liturgy during the reign of King Jeongjo reveal Samsaebulhoedo at Yongjusa Temple to be an original version produced at the time of the founding of Yongjusa Temple in 1790. According to a comparative analysis of formats, iconography, styles, aesthetic sensibilities, and techniques found in Buddhist paintings and paintings by Joseon court painters from the eighteenth and nineteenth centuries, Samsaebulhoedo at Yongjusa Temple bears features characteristic of paintings produced around 1790, which corresponds to the result of analysis on the written prayer. Buddhist paintings created up to the early eighteenth century show deities with their sizes determined by their religious status and a two-dimensional conceptual composition based on the traditional perspective of depicting close objects in the lower section and distant objects above. This Samsaebulhoedo, however, systematically places the Buddhist deities within a threedimensional space constructed by applying a linear perspective. Through the extensive employment of chiaroscuro as found in Western painting, it expresses white highlights and shadows, evoking a feeling that the magnificent world of the Buddhas of the Three Ages actually unfolds in front of viewers. Since the inner order of a linear perspective and the outer illusion of chiaroscuro shading are intimately related to each other, it is difficult to believe that the white highlights were a later addition. Moreover, the creative convergence of highly-developed Western painting style and techniques that is on display in this Samsaebulhoedo could only have been achieved by late-Joseon court painters working during the reign of King Jeongjo, including Kim Hongdo, Yi Myeong-gi, and Kim Deuksin. Deungun, the head monk of Yongjusa Temple, wrote Yongjusa sajeok (History of Yongjusa Temple) by compiling the historical records on the temple that had been transmitted since its founding. In Yongjusa sajeok, Deungun recorded that Kim Hongdo painted Samsaebulhoedo as if it were a historical fact. The Joseon royal court's official records, Ilseongnok (Daily Records of the Royal Court and Important Officials) and Suwonbu jiryeong deungnok (Suwon Construction Records), indicate that Kim Hongdo, Yi Myeong-gi, and Kim Deuksin all served as a supervisor (gamdong) for the production of Buddhist paintings. Since within Joseon's hierarchical administrative system it was considered improper to allow court painters of government position to create Buddhist paintings which had previously been produced by monk-painters, they were appointed as gamdong in name only to avoid a political liability. In reality, court painters were ordered to create Buddhist paintings. During their reigns, King Yeongjo and King Jeongjo summoned the literati painters Jo Yeongseok and Kang Sehwang to serve as gamdong for the production of royal portraits and requested that they paint these portraits as well. Thus, the boundary between the concept of supervision and that of painting occasionally blurred. Supervision did not completely preclude painting, and a gamdong could also serve as a painter. In this light, the historical records in Yongjusa sajeok are not inconsistent with those in Ilseongnok, Suwonbu jiryeong deungnok, and a prayer written by Hwang Deok-sun, which was found inside the canopy in Daeungjeon Hall at Yongjusa Temple. These records provided the same content in different forms as required for their purposes and according to the context. This approach to the Samsaebulhoedo at Yongjusa Temple will lead to a more coherent explanation of dating the painting, analyzing its style, identifying its painter, and interpreting the relevant documents based on empirical grounds and logical consistency.