• Journal of the Korean Society for Railway
• /
• 제11권1호
• /
• pp.54-60
• /
• 2008

In the trackbed design using elastic multilayer model, the stress-dependent resilient modulus $(E_R)$ is an important input parameter, that is, reflects substructure performance under repeated traffic loading. However, the evaluation method for resilient modulus using repeated loading triaxial test is not fully developed for practical purpose, because of costly equipment and the significantly fluctuated values depending on the testing equipment and laboratory personnel. The this study, the paper will present an indirect method to estimate the resilient modulus using dynamic properties. The resilient modulus of crushed stone, which is the typical material of sub-ballast, was calculated with the measured dynamic properties and the range of stress level of the sub-ballast, and approximated with the power model combined with bulk and deviatoric stresses. The resilient modulus of coarse grained material decreases with increasing deviatoric stress at a confining pressure, and increases with increasing bulk stress. Sandy soil (SM classified from Unified Soil Classification System) of subgrade was also evaluated and best fitted with the power model of deviatoric stress only.

• International Journal of Highway Engineering
• /
• 제13권4호
• /
• pp.41-50
• /
• 2011

It is well-known that pavement is easily damaged by several factors including permanent deformation and fatigue crack, causing service life of the pavement to be shorter than expected. It is very important to predict amount of permanent deformation for designing pavement and developing design method of pavement. A new model of permanent deformation of pavement materials based on concept of shear stress ratio has been proposed because the lower pavement materials are highly affected by shear strength of the material. In this study a large repetitive triaxial load test has been adapted for performing test of permanent deformation of crushed subbase materials. The test procedure which includes concept of shear stress ratio has been newly developed. Several important model parameters can be obtained from the test that can be used for making correct permanent deformation model of the material.

• Journal of Industrial Technology
• /
• 제24권B호
• /
• pp.89-94
• /
• 2004

This Study is results of experimental works to investigate the characteristics of vibro-compaction of crushed stones having coarse grain sizes. For testing material, crushed stone, sieved within very narrow ranges of grain size distribution, was used. Cyclic loading apparatus was used to apply cyclic loading to the specimen prepared in the mold. Tests were performed by changing the ratio of the maximum to the minimum stress, frequency and the magnitude of the maximum and the minimum stresses. Settlement of specimen due to cyclic loading was measured to analyze the compaction efficiency and sieve analysis test after cyclic loading test was also carried out to find the crushing rate of the specimen. As results of cyclic loading test, normalized settlement in terms of specimen height tends to be converged around loading cycle number of 1500. The magnitude of normalized settlement is in the range of 3.11 ~ 8.57%. The crushing rate is in the range of 4.46 ~ 8.78%. Normalize settlement and the crushing rate tend to increase with decreasing the ratio of the maximum to the minimum stresses and they tend to increase with increasing the frequency and the magnitude of the maximum and the minimum stresses for the given ratio. In conclusions, compaction rate of crushed stone is controlled by the dynamic stress (difference between the maximum and the minimum stresses) and the crushing rate is dominated by applied energy to the specimen.

• Journal of the Korean Geotechnical Society
• /
• 제30권8호
• /
• pp.25-37
• /
• 2014

In load and resistance factor design (LRFD) method, resistance factors are typically calibrated using resistance bias factors obtained from either only the data within ${\pm}2{\sigma}$ or the data except the tail values of an assumed probability distribution to increase the reliability of the database. However, the data selection approach has a shortcoming that any low-quality data inadvertently included in the database may not be removed. In this study, a data quality evaluation method, developed based on the quality of static load test results, the engineering characteristics of in-situ soil, and the dimension of aggregate piers, is proposed for use in constructing database. For the evaluation of the method, a total 65 static load test results collected from various literatures, including static load test reports, were analyzed. Depending on the quality of the database, the comparison between bias factors, coefficients of variation, and resistance factors showed that uncertainty in estimating bias factors can be reduced by using the proposed data quality evaluation method when constructing database.

• Journal of the Korean GEO-environmental Society
• /
• 제6권3호
• /
• pp.17-23
• /
• 2005

In Korea, the production of reclaimed concrete materials has been increased due to the increase in the concrete structures taken down every year. The reclaimed concrete materials have been reused as road materials. However, the studies on their mechanical and environmental properties have been very limited. The recycled rate of the materials is currently low in Korea. This paper presents the investigation of mechanical and environmental properties of the reclaimed concrete materials, as well as the comparisons with those of gravel. For the evaluation of the mechanical and environmental characteristics, following tests were conducted on both reclamed materials and gravel; liquid limit, plasticity index, CBR, sand equivalent test, abrasion test, pH test, and column leaching test. The test results showed that the reclaimed concretes satisfy the requirements for use as roadbase, subbase, and subgrade materials, except base materials. The pH of reclaimed concrete materials was less than 11 and the leaching test results satisfied the regulatory requirement of Waste Management Act in Korea. Based on the investigations, it appears that the reclaimed concrete materials are environmentally safe and applicable for use as road materials.

• Journal of the Korean Geosynthetics Society
• /
• 제13권2호
• /
• pp.11-20
• /
• 2014

To create a large-scale complex, it is often the case to perform ground improvement by using vertical drain method after the reclamation of coastal soft ground, for construction period shortening and stable site renovation. During this process, the pore water migrates to the horizontal drainage layer of the ground surface through the vertical drain installed in the soft ground and discharged out to the open. In the past sand was used as the material for the horizontal drainage layer in numerous cases, however recently, due to material shortage and high pricing, the use of crushed stones has increased. To prevent mixing of the materials between the horizontal drainage layer and the upper landfill, geosynthetics (PPMat) are installed. However, the use of geosynthetics results in high additional cost for material purchase and installation, therefore it is necessary to examine the validity of the installation itself. In this study, to verify the necessity, model tests were performed. Results from the model tests indicate that the drainage ability of the horizontal drainage layer is barely affected by the application of geosynthetics.

• Journal of the Korean Geosynthetics Society
• /
• 제6권1호
• /
• pp.17-25
• /
• 2007

This study presents a modeling approach for geogrid-encased stone column(GESC) method which is widely used in Europe as an alternative to conventional pile foundations. Several benefits of using the stone column method include sound performance, low cost, expediency of construction, and liquefaction resistance, among others. Recently, geosynthetic-encased stone column approach has been developed to improve load carrying capacity through increasing confinement effect. The aim of this research is to establish a systematic approach for modeling of GESC and to form a database for the fundamentals of GESC. This paper presents details of 3D modeling of GESC together with the general behavior of GESC.

• Journal of the Korean GEO-environmental Society
• /
• 제12권6호
• /
• pp.5-15
• /
• 2011

In this study, centrifuge model tests were performed to investigate stress concentration ratio, stress characteristics of soft clay ground improved by granular compaction piles with changes of piles type, loading condition and area replacement ratio. From the results of rigid loading tests, while vertical stresses acting on clay ground is similar, vertical stresses acting on GCP is larger than those acting on SCP with same replacement ratio. Also, average stress concentration ratio is increased proportionally with increasing the area replacement ratio of GCP and SCP. It was evaluated that average stress concentration ratio of soft clay ground improved by GCP is larger than that of SCP. As a result of flexible loading tests, stress concentration ratio is the highest when replacement ratio of GCP and SCP is 40%. Average stress concentration ratio of soft clay ground improved by GCP is a little more higher than is improved by SCP.

• Proceedings of the Korea Water Resources Association Conference
• /
• 한국수자원학회 2022년도 학술발표회
• /
• pp.367-367
• /
• 2022

토지이용의 고도화에 따라 비점오염원 부하는 증가하는 추세이며 기후변화에 따른 강우강도 증가 등으로 지표면에 축적된 고농도의 비점오염물질이 하천으로 유출, 수질오염을 가중시키고 있어 비점오염원 관리가 필요하다. LID 기법은 자연적 기작(mechanisms)과 공정(process)을 이용하여 생태계의 물질순환(물순환 포함)과 에너지 흐름이 원활하도록 조성하는 기법으로, 불투수층면에서 발생되는 강우유출수를 관리 가능하다. LID 시설에는 전처리 시설을 두어 초기 고농도의 입자상 물질을 저감시키고, 강우유출수 저류공간을 통한 유출저감, 첨두유량 등을 저감시킨다. 이러한 전처리 시설에는 유기물질 및 영양소의 생물학적 제거를 위한 미생물 서식공간의 제공 등의 역할을 수행하기 위하여 다양한 여재를 적용하고 있다. 본 연구는 비점오염물질 유입이 LID 기법 전처리 시설 내 여재층의 물리·화학적 및 생물학적 환경을 평가하였다. 3개 시설 모두 100%의 불투수층에서 발생되는 강우유출수를 처리하는 LID 시설을 연구대상으로 선정하였으며, 각각의 전처리 시설에는 자갈, 우드칩, 쇄석 등이 적용되어 있다. 퇴적물의 경우 가장 상부에 존재하는 층으로 퇴적물의 오염물질 농도는 2~10.7배 이상 매우 높게 나타났다. 우드칩의 경우 다른 여재에 비해 높은 함수량과 유기물 함량을 보였으며 이는 우드칩의 수분을 보유하는 능력과 거친 표면공극에 오염물질이 부착되기 때문으로 나타났다. 또한, 같은 무기성 여재인 쇄석과 자갈의 경우 여재 크기의 차이를 보임에도 불구하고 미생물의 군집구성과 함수량의 차이를 보이는 것으로 평가되었다. 유기물의 함량이 낮은 강우유출수의 생물학적 처리능력을 향상시키기 위해서는 유기성 여재가 필요하며, 다공성 무기 멀칭재를 적용하고 하부의 토양은 적정 유기물을 배합하여 질산화 및 탈질화 유도가 가능하도록 설계가 필요한 것으로 분석되었다.

• Journal of the Korean Geotechnical Society
• /
• 제24권1호
• /
• pp.15-23
• /
• 2008

In this study, modeling shear characteristics of a coarse material mainly containing crushed stones were implemented using PFC2D, a commercially available code based on DEM(Discrete Element Method). Using the DEM code, this study provides the methodology considering the shear characteristics due to a irregular grain shape, GSD(Grain Size Distribution) and porosity of coarse material which are not effectively incorporated in conventional continuum numerical codes. Direct shear test was simulated for the GSD and porosity generated sample using the code and the simulated results showed very good agreement with the laboratory test results. The current modeling approach can be applied to other coarse materials having various GSD and porosities. Using such application, prediction of the strength characteristics of coarse material in field scale would be possible, which is limited in laboratory scale so far.