• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.102-110
• /
• 2023

This paper introduces scarf welding process of thin substrates using flexible laser transmission welding (f-LTW) technology. We examined the behavior of tensile strength relative to the scarf angle for flexible applications. Thin plastic substrates with the thickness of less than 100 ㎛ were bonded and a jig to form a slope at the edge of the substrate was developed. By developing the scarf welding process, we successfully created a flexible bonding technology that maintains joint's thickness after the process. The tensile strength of the joint was assessed through uniaxial test, and we found that the tensile strength increases as the slope of bonding interface decreases. By conducting stress analysis at the bonding interface with respect to the slope angle, design factor of bonding structure was investigated. These findings suggest that the tensile strength depends on the geometry of the joint, even under the same process conditions, and highlights the significance of considering the geometry of the joint in welding processes.

• Korean Journal of Food Science and Technology
• /
• v.10 no.1
• /
• pp.78-82
• /
• 1978

In a series of studies on the utilization of persimmons, the purpose of this experiment was to examine the optimum thickness of film using different number of persimmons per film bag. 'Fuyu', persimmon variety was used in this investigation. The results obtained were as follows: The optimum thickness of the film bag was 0.08mm, 0.06mm, and 0.04mm for the bags packed with 3, 10 and 50 persimnons, respectively. The changes in the ratio of firmness, loss of fresh weight, titrable acidity and percentage of sugar contents were minimal in these three optimum combinations than the others. These results could be explained by the balanced optimum gas concentration, $CO_2$ 5-10% and $O_2$ 5%, in those three optimum combination. Therefore, it was suggested that the different thickness of film bag needs a particular number of fruits packed per bag for the long term storage in persimmons.

• Investigative Magnetic Resonance Imaging
• /
• v.1 no.1
• /
• pp.103-107
• /
• 1997

Purpose: To investigate the localization and functional lateralization of the supplementary motor area (SMA) in motor activation tests in comparison to that of the primary motor area. Materials and Methods: Seven healthy volunteers obtained echoplanar imaging blood oxygen level dependent technique. This study was carried on 1.5T Siemens Magnetom Vision system with the standard head coil. Parameters of EPI were followed as; TR/TE : 1.0/66.0msec, flip angle: $90^{\circ}$, field of view: $22cm{\times}22cm,{\;}matrix:{\;}128{\times}128$, slice number/slice thickness/gap: 1O/4mm/0.8mm with fat suppression technique. Motor task as finger opposition in each hand consisted of 3 sets of alternative rest and activation periods. Postprocessing were done on Stimulate 5.0 by using cross-correlation statistics. To compare the functional lateralization of the SMA in the right and left hand tests, each examination was evaluated for the percent change of signal intensity and the number of activated voxels both in the SMA and in the pri¬mary motor area. Hemispheric asymmetry was defined as difference of summation of the activted voxels between each hemisphere. Results: Percent change of signal intensity in the SMA (2.49 -3.06%) is lower than that of primary motor area(4.4 -7.23%). Percent change of signal intensity including activated voxels were observed almost equally in the right and left SMA. As for summation of activated voxels, primary motor area had significant difference between each hemisphere but not did the SMA. Conclusion: Preferred contralateral dominant hemisphere and hemispheric asymmetry were detected in the primary motor area but not in the SMA.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.238-238
• /
• 2012

Ag (silver)의 일함수는 T-OLED (Top Emission Organic Light Emitting Diode)의 전극소자로 사용하기에는 다소 낮다는 단점이 있다(~4.3 eV). 이러한 단점을 해결하기 위한 대안으로 Ag 박막의 표면을 플라즈마 처리, UV 처리 및 열처리를 통하여 일함수를 높이는 연구가 진행 되어왔다(>5.0 eV). 하지만 현재의 대부분 연구는 후 처리된 박막의 일함수에 초점을 맞춰 연구가 진행 되어 박막의 nano-mechanical property에 대한 연구는 매우 부족하다. 따라서 본 논문에서는 AgOx 박막의 nano-mechanical property에 초점을 맞춰 분석을 실시하였다. 연구에 사용된 샘플은 Ag 박막을 유리기판 위에 rf-magnetron sputter 장치를 이용하여 100 W의 power로 150 nm 두께로 증착하였다. 증착된 Ag 박막은 $O_3$ 발생 UV 램프를 이용하여, 다양한 시간동안 UV 처리하였다(0~9분). 증착된 샘플은 Four-point probe, nanoindenter 장비를 이용하여 nano-mechanical property를 분석하였다. 실험 결과 UV 처리 시간이 0, 1분에서 면저항이 0.16, 0.50 ${\Omega}$/sq로 급격한 변화가 나타났으나, 반면 3분 이후 9분의 샘플의 경우, 0.55 ${\Omega}$/sq에서 0.24, 0.20, 0.15 ${\Omega}$/sq로 감소하여 전기적 특성변화를 볼 수 있었다. 또한 nanoindenting 결과 UV 처리한 박막의 극 표면 경도 값의 변화는 0~5분 처리한 샘플의 경우, 물리적인 경도가 증가하는 형태를 보이며 UV 처리를 5분간 했을때 7.89 GPa로 최고의 경도를 가진다. 그 이후부터는 6.97, 3.46 GPa의 결과로 박막의 경도가 감소되는 결과를 얻었다. 이러한 결과로부터 Ag 박막의 후처리에 따른 Ag 물질의 산화 및 결정상태에 따라 박막 내에 존재하는 residual stress를 분석할 수 있다.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.3
• /
• pp.15-23
• /
• 2017

Gangwon Province, located in the northeastern part of South Korea, is the coldest area in South Korea with 90% of the total area as mountainous. Therefore, tunnel damage has been reported continuously in winter. But there has been lack of researches on frost heave occurring behind tunnel lining. In this study, numerical analysis was conducted to investigate the frost depth in road tunnel constructed in Gangwon province. Based on the database on road tunnel and weather in Gangwon province, a standard tunnel shape and geotechnical properties of ground was determined. And then thermal analysis for the frost depth according to the temperature change and ground conditions were conducted. Analysis result showed that the sensitivity to frost heave of metamorphic rock and sedimentary rock is higher than sand. Lower initial ground temperature leads to deeper frost depth and consequently increases frost damage. In addition, lining thickness, specific heat capacity, and thermal conductivity also affect greatly on the variation of frost depth.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.2
• /
• pp.397-415
• /
• 2004

This study surveyed differences among KS, ISO, JIS and ANSI ophthalmic spectacle lenses standards. These standards applied to several lenses that were in common currency and we checked over problems and improvements in KS. KS corresponded to ISO, for the most part, and ANSI, partly. But terms, definitions, progressive power lenses standards, UV transmittance and base curves clauses did not exist in KS. There was no differences between nominal data and actual data in important clauses estimation-minimum requirements on refractive power, tolerances on the size of lenses, material and surface quality. But tolerances of thickness, base curves, UV and visible transmittance values were not existing, there were differences among several ophthalmic spectacle lenses in the test of these clauses. These requirements will be needed for better and more comfortable vision.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.1
• /
• pp.23-26
• /
• 2014

Ga doped ZnO (GZO) single layer and GZO/ZnO bi-layered films were deposited on glass substrates by radio frequency magnetron sputtering and then the influence of film thickness on the structural, electrical, and optical properties of the films was considered. Thicknesses of the GZO/ZnO films was varied as GZO 100 nm, GZO 85 nm/ZnO 15 nm and GZO 70 nm/ZnO 30 nm, respectively. The observed result means that optical transmittance and electrical resistivity of the films were influenced with film thickness and GZO 85 nm/ZnO 15 nm bilayered films show the higher figure of merit than that of the films prepared other films in this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5844-5853
• /
• 2014

This paper presents the results of experimental investigations on the shear failure behaviors of reinforced concrete beams using ductile fiber reinforced cementitious composite (DFRCC). Total 10 RC beams of $150{\times}300{\times}1,000mm$ size were tested by 4-point bending under the displacement control. The main parameters of the experiment are surface treatment by grinding and preloading to the cracking point in the repair process. The load-displacement curves, diagonal tension cracking load, flexural cracking load, and shear strength were obtained. The test results showed that the DFRCC can be used effectively for restoring the shear strength approximately 99% to the original value under the condition that the appropriate thickness and surface treatment like grinding are assured. For further research, the specimens taken from real deteriorated structures will need to be tested after being repaired with DFRCC.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.52-60
• /
• 2001

Physical properties of foams depend on the density of foams, Physical properties of base polymers, open ceil contents, and cell structures including the size, size distribution, shape of ceil and the thickness of membrane and strut. The density of foam is affected by raw materials, concentration oi crosslinking agent and blowing agent and process parameters such as processing technique and condition. Ethylene vinyl acetate copolymer(EVA) foam is a crosslinked cellular material. The foaming characteristics and physical properties of EVA foam are affected by decomposition rate of blowing agent. In this study, the decomposition rate of blowing agent and crosslinking rate, foaming characteristics and physical properties of foams were evaluated. The slow decomposition rate of blowing agent results in low density foam, good shock absorption property and uniform cell size distribution compared to the high decomposition rate of blowing agent.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.2
• /
• pp.133-138
• /
• 2012

The purpose of this study was to examine the correlation between physical properties of dried coacervate films and dry feel for shampoo composition. Simple shampoo compositions were made of two different cationic charge density polymers in the same surfactant compositions. The simple shampoo compositions were diluted with distilled water to make coacervate. Formed coacervate was collected by centrifuge (3,000 rpm, 30 min). Coacervate was coated on the glass plates and dried in drying oven (for 1 h, $50^{\circ}C$) to make the thin film. We carried out an experiment on measurement of contact angle, moisture loss ratio and SEM image analysis of the dried coacervate film. Dry feelings of the shampoos were evaluated by panel using hair tresses. Results show that the properties of dried coacervate films affect the dry feel of the after shampooing.