• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.13-20
• /
• 2014

The natural convection heat transfers of a helical coil in a duct were measured experimentally varying the inclination. To achieve high Rayleigh number, mass transfer experiments instead of heat transfer experiments were performed based upon the analogy. The $Ra_D$ was fixed to $4.55{\times}10^6$. The turn numbers were 1~10. the pitch to diameter ratio were 1.3~5, and the inclination of the helical coil $0^{\circ}{\sim}90^{\circ}$. The measured $Nu_D$ for a single turn of the helical coil was very close to that from McAdams heat transfer correlation for a horizontal cylinder. The heat transfers of the helical coil were varied by the pith, number of turns, and duct height in a complex manner showing the velocity, chimney, and pre-heating effects. The results of the study contributes to the phenomenological analyses of the natural convection heat transfer of a compact heat exchanger.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.118-122
• /
• 2016

When a geometric size of moonpool and an inflow velocity are determined based on the similarity of Froude number, Reynolds number is depending on the scale ratio of moonpool geometry. It means that different characteristics of flow fluctuations in moonpool can be observed depending on the scale ratio of moonpool even though Froude number is the same. In the present study two dimensional numerical simulations were performed to investigate the influence of scale ratios on the flow characteristics inside the moonpool. The inflow velocity at several scale ratios was determined to keep Froude number constant. A periodic response was observed in a small size of moonpool while a large moonpool showed complicated fluctuations with various amplitudes and frequencies, which made it difficult to distinguish the statistical steady-state response from the temporal responses in the case of large moonpool. The similarity of Froude number gave rise to a spectral characteristic which was inversely proportional to the square root of scale ratios ($f_{0.5}{\approx}{\sqrt{2}}f_1{\approx}2f_{2.0}$) but a low frequent occurrence of strong vortex ($f_{2.0}=0.07$)which is observed inside the large moonpool was characterized depending on scale ratios.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.403-413
• /
• 2015

This paper presents the cutter bit damage due to the rotation speed of shield TBM cutter head in the mixed ground. The efficient of cutter bits and disk cutter are very important for tunnelling in mixed ground. In particular, this research is focused on the performance of cutter bits during excavation in mixed ground which is consist of the weathered soil and rock formation. In order to carry out this research, the experimental works are prepared performed by using the scaled shield TBM cutter bits evaluation machine developed. The mixed ground is prepared considering with a scale effect of tunnel size. Three different rotation speeds of shield TBM cutter head (i.e. 2, 3, 4 rpm) are applied in the experimental work. The drag forces acting on the cutter bits are measured at each cutter bit during rotation of cutter head. It is also analysed the variation of drag forces due to the rotation speed of shield TBM cutter head. The results of this research are clearly shown that the drag forces acting on the cutter bits are jumped up at the boundary between weathered soil and rock. It is also indicated that the jamping drag forces are increased with increasing the rotation speed of the cutter head. It is found from the research that the higher rotation speed of shield TBM cutter head will be high risk in the mixed ground. It is, therefore, suggested that the use of lower rotation speed of shield TBM cutter head is recommended for reducing the cutter bit damage in practice.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.1
• /
• pp.43-48
• /
• 1997

The present study is aimed to investigate experimentally on the hydrodynamic behaviours of air ~ pulverized coal flow in rectangular combustor with cavity. Mean velocity, density and tur¬bulent properties of pulverized coal in rectangular entrained flow combustor were measured by PDA. Experimental results show that the flow reattachment point at the lower plane in the com¬buster chamber has been developed near X/D= 15. The similarities at each section are found after the flow reattachment point. The maximum values of turbulent intensity and Reynolds shear stress have been shown near Y/D=6, which is higher than centerline. The maximum density of the pulverized coal sited in the range ofY/D=6~8.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.11-15
• /
• 2011

Heat transfer equation is first reviewed and then governing equation of moisture diffusion. Analogy scheme is applied to analysis the moisture absorption problem of polymers. It make possible to numerically analyze the diffusion problem for single medium by using commercial finite element code if it is under the isothermal loading condition. It is extended to special multimaterial system by introducing pressure ratio function, whose moisture characteristics of materials are proportional to temperature only. The weight changes of silicon-nonconductive-polymer joint model due to moisture absorption is measured and been very close to the numerical results as for single media with boundary condition with zero concentration, but yields numerical errors as for multisystem media.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.2
• /
• pp.165-174
• /
• 1995

It is well known that the behavior of R /C members under static cyclic loading is somewhat different from that under dynamic cyclic loading, such as earthquake loading, because static loading rate is substantially lower than that corresponding to the Frequencies of seismic excitation. The purpose of this research is to estabilish the reliance for modeling techniques of small-scale specirr~ens subjected to dynamic cyclic loading. This research focused on the similitude requirements for reinforced concrete frame structures subjeced to dynamic cyclic loading. Length scale ratio of specimens were 1 : 2 : 4, and eleven specimens were tested at the frequencies of 0.0025Hz-2.OHz. It was confirmed that rnode1ir.g techniques based on the similitude requirements were useful methods to evaluate the behavior of full-size R /C structures subjected to earthquake type loading.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.101-112
• /
• 2013

Large eddy simulation was performed to investigate the effect of linearly increasing wall disturbance on the modification of turbulent characteristics of temperature field in the vicinity of the wall. It was noted that temperature variance increased monotonically whereas temperature dissipation decreased significantly, resulting in a noticeable reduction in both time and length-scales. A sudden drop in turbulent Prandtl number down to around 0.25 in the near-wall region indicated that the similarity between velocity and temperature fields decreases near the wall as a result of linear wall disturbance.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.1
• /
• pp.1-6
• /
• 1979

본연구에서는 그물어구의 상사를 지배하는 무차원수 K를 $$K=\frac{{\nu}^n\rho_wv^{2-n}}{{d^{1+n}(\rho-\rho_w)}$$ d, p: 재료의 직경 및 밀도 $\nu,\rho_w,v$: 물의 동점성계수, 밀도 및 속도으로 정하고, 여기에서의 직경의 비를 결정하는 방법에 따라 실물과 모형과의 상사를 완전하게 그리고 근사적으로 만족시키는 조건들을 구하였다. 즉, 원전한 상사한 경우는 직경의 비를 축척비와 같게 하고, 나아가서 다른 모든 치수의 비도 축척비와 같게 함으로써 만족된다고 하였으며, 측사적 상사의 경우느 직경의 비가 축척비 $(\frac{\lambda_2}{\lambda_1})$와 같지 않아도 된다고 하여, 그물실의 직경 d, 코의 크기 $\iota$ 및 콧수 N의 비를 $$\frac{d_2}{d_1}=\frac{\iota_2}{\iota_1}=\frac{\lambda_2}{\lambda_1}{\cdot}\frac{N_1}{N_2}$$ 으로, 줄의 직경 d', 길이 $\iota'$ 및 밀도 $\rho'$의 비를 $$\frac{d_2'}{d_1'}=\sqrt{{\frac{\lambda_2}{\lambda_1}}\cdot{\frac{d_2}{d_1}}\cdot{\frac{\rho_2-\rho_{w2}}{\rho_1-\rho_{w1}}\cdot{\frac{\rho_1'-\rho_{w1}}{\rho_2'-\rho_{w2}}}}$$, $\frac{\iota_2'}{\iota_1'}=\frac{\lambda_2}{\lambda_1}$로, 부속구의 치경 $d'$, 밀도 $\rho'$ 및 수 $N'$의 비를 $$\frac{N_2'}{N_1'}=(\frac{\lambda_2}{\lambda_1})^2(\frac{d_2}{d_1})(\frac{d_1'}{d_2'})\frac{(\rho_2-\rho_{w2})}{(\rho_1-\rho_{w1})}\frac{(\rho_1'-\rho_{w1})}{(\rho_2'-\rho_{w2})}$$으로 정하였다. 이렇게 정해진 모형어구에 대해 유속 v의 비느 $K_1=K_2$로부터 $$(\frac{u_2}{u_1})^{2-n}=(\frac{\nu_2}{\nu_1})^{-n}\;(\frac{\rho_{w1}}{\rho_{w2}})\;(\frac{\rho_2-\rho_{w2}}{\rho_1-\rho_{w1}})\;(\frac{d_2}{d_1})^{1+n}$$으로 주어지므로, 이를 이용하여 어구저항 D 및 그물감의 다리에서의 장력 $\tau$의 비를 $$\frac{D_2}{D_1}=\frac{d_2(\rho_2-\rho_{w2})}{d_1(\rho_1-\rho_{w1})}(\frac{\lambda_2}{\lambda_1})^2$$ $${\frac{\tau_2}{\tau_1}=\frac{d_2\iota_2(\rho_2-\rho_{w2})}{d_1\iota_1(\rho_1-\rho_{w1})}\;{\cdot}\frac{\lambda_2}{\lambda_1}$$로 정하였다.

• Proceedings of The KACE
• /
• 2018.01a
• /
• pp.69-72
• /
• 2018

4차 산업혁명의 본격화로 과거 효율성과 생산성이 중점이 되던 경영 패러다임에서 벗어나 혁신, 창의성, 유연성이 대두되는 경영 패러다임으로 변화되고 있다. 이러한 변화된 환경 속에서는 조직 구성원들의 창의적인 업무수행이 조직에게 경쟁우위를 가져다주는 새로운 지식과 아이디어의 원천이면서 동시에 기업이 지속적으로 성장하고 살아남기 위한 필수 요소가 된다. 조직 및 상사의 강제적 견인보다는 구성원들 스스로 목적의식을 가지고 업무를 수행하는 과정에서 창의적 업무수행은 가장 잘 발현될 수 있으며, 본 연구를 통해 창의적 업무수행 과정에서 가장 핵심이 되는 내재적 동기부여의 관점에 초점을 맞추어 게이미피케이션 메커니즘과 접목시켰을 때 조직구성원들에게 동기부여를 발현시킬 수 있는지에 대해 연구하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.259-268
• /
• 2012

This study measured the natural-convection heat transfer of two vertically staggered cylinders with varying vertical pitch-to-diameter ($P_v$/D) and horizontal pitch-to-diameter ($P_h$/D) ratios. The measured heat-transfer rates for the lower cylinder agreed well with the existing heat-transfer correlations for a single cylinder. At the smallest $P_v$/D, the rising plume from the lower cylinder provides the upper cylinder with a preheated flow, and the heat-transfer rates of the upper cylinder decrease, but increase very sensitively with $P_h$/D. However, at the largest $P_v$/D, the velocity effect dominates, and the heat-transfer rates of the upper cylinder are larger than that of a single cylinder, and decrease less sensitively with $P_h$/D. Even if $P_h$/D is increased, the heat-transfer rate of the upper cylinder is higher than that of the lower cylinder because of the chimney and side flow effects. This work expanded the flow ranges to turbulent flows. The cupric acid-copper sulfate ($H_2SO_4-CuSO_4$) electroplating system was adopted for the measurements of the mass-transfer rates instead of the heat-transfer experiments based on the analogy concept. The measurements were made by varying $P_v$/D (1.02-5) and $P_h$/D (0-2) in both laminar and turbulent flows. The Rayleigh number ranged from $1.5{\times}10^8$ to $2.5{\times}10^{10}$, and the Prandtl number was 2,014.