• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.5 s.39
• /
• pp.79-89
• /
• 2004

This paper presents the results of experimental studies on the equipment isolation effect in the nuclear containment. For this purpose, shaking table tests were performed. The purpose of this study is enhancement of seismic safety of equipment in the Nuclear Power Plant. The isolation system, known as Friction Pendulum System (FPS), combines the concepts of sliding bearings and pendulum motion was selected. Peak ground acceleration, bidirectional motion, effect of vertical motion and frequency contents of selected earthquake motions were considered. As a result, these are founded that the vertical motion of seismic wave affect to the base isolation and the isolation effect decreased in case of near fault earthquake motion.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.8-12
• /
• 2008

For the reduction of fabrication cost and process time of AC plasma display panel (PDP), indium tin oxide (ITO) layer was patterned as bus electrode using Nd:$YVO_4$ laser. In comparison with the chemically wet etched ITO patterns, laser ablated ITO patterns showed the formation of shoulders and ripple-like structures at the edge of the ITO lines. For the reduction of shoulders and ripple-like structures, pulse repetition rate and scan velocity of laser was changed. In addition, we analyzed a discharge characteristic of PDP test panel to observe how the shoulders and ripple-like structures influence on the PDP. Based on experimental results, the pattern etched at the 500 mm/s and 40 kHz was better than any other condition. From this experiment we could see the possibility of the laser direct patterning for the application to the patterning of ITO in AC-PDP.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1645-1652
• /
• 2016

FTN(Faster-Than-Nyquist) signaling is a method of transmitting symbols at rates faster than the Nyquist rate in the same bandwidth by overlapping transmission pulses. The transmission power of the FTN signal is greater than that of the Nyquist signal, because the number of symbols in the FTN signal is larger than that in the Nyquist signal for the same time interval. Hence, to evaluate the performance of an FTN-based transmission system properly, the performance evaluation criterion should be carefully set, and conversion formulas among the criteria which are used in Nyquist-based system should also be applied attentively. In this paper, the performance evaluation criteria of the FTN-based transmission system is analyzed and a valid way to set the criteria is proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.134-134
• /
• 2009

In this work, we report that crystallization speed as well as the electrical and optical properties about the N-doped $Ge_2Sb_2Te_5$ thin films. The 200-nm-thick N-doped $Ge_2Sb_2Te_5$ thin film was deposited on p-type (100) Si and glass substrate by RF reactive sputtering at room temperature. The amorphous-to-crystalline phase transformation of N-doped $Ge_2Sb_2Te_5$ thin films investigated by X-ray diffraction (XRD). Changes in the optical transmittance of as-deposited and annealed films were measured using a UV-VIS-IR spectrophotometer and four-point probe was used to measure the sheet resistance of N-doped $Ge_2Sb_2Te_5$ thin films annealed at different temperature. In addition, the surface morphology and roughness of the films were observed by Atomic Force Microscope (AFM). The crystalline speed of amorphous N-doped $Ge_2Sb_2Te_5$ films were measured by using nano-pulse scanner with 658 nm laser diode (power : 1~17 mW, pulse duration: 10~460 ns). It was found that the crystalline speed of thin films are decreased by adding N and the crystalline temperature is higher. This means that N-dopant in $Ge_2Sb_2Te_5$ thin film plays a role to suppress amorphous-to-crystalline phase transformation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.70-70
• /
• 2009

Si 도핑한 $Ge_2Sb_2Te_5$ 박막은 비정질상에서의 열적 안정성증가, fcc에서 hex상으로의 상전이 억제, 활성화 에너지 증가 등의 특성을 보인다. 본 연구에서는 Si 도핑에 의한 $Ge_2Sb_2Te_5$ 박막의 전기적 그리고 구조적인 특성에 관한 실험을 진행하였다. 실험에 사용된 Si 도핑 $Ge_2Sb_2Te_5$ 박막은 Si 기판 위에 radio frequency power supply를 사용해 Si과 $Ge_2Sb_2Te_5$ 타겟을 co-sputtering하여 증착하였다. Si의 sputtering 파워를 달리하여 실리콘의 농도를 다르게 증착 하였고 X-ray photoelectron spectroscopy (XPS)를 사용하여 박막의 Si 농도를 측정하였다. 증착된 박막은 질소 분위기 하에서 $5\;^{\circ}C$/min으로 열처리 하여 여러 온도와 Si 농도에서의 박막의 특성을 측정하였다. 열처리 전, 후의 박막은 X-ray diffraction (XRD) 분석을 통하여 각각의 온도에서의 구조적 특성을 분석하였다. 열처리 온도에 따르는 필름의 전기적 특성 파악을 위해서 four-point probe를 이용하여 박막의 면저항을 측정하였고 그 값은 3 회 이상 측정하여 평균값을 사용하였다. Nano-pulse scanner를 사용하여 다양한 파워범위와 펄스폭 범위에서의 박막의 상변화에 따른 반사도 차이를 측정하여 각 조성에서의 비정질-결정질상 변화속도를 분석하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.240-245
• /
• 2004

This paper presents a Switched Reluctance Motor(SRM) drive using the self-tuning control method to achieve the maximum torque. SRM has the difficulty to research it by an analytic method and to control the speed End torque because of the high nonlinearity. So, in this paper, the self-tuning control method is applied to relevantly controlling turn-on/off angle to operate at the maximum torque. Also, the feedback signals to control the turn-on/off angle are the encoder pulse and the increment of phase current. At first, n adequate turn-off angle is searched by itself and then a turn-on angle is done. As the relationship between turn-on and him-off angle is mutual dependent, the turn-on/off angle is controlled by a real time self-tuning control method in order to maintain the maximum torque. The proposed self-tuning Algorithm is verified by experiments.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.475-479
• /
• 2003

Traditional ultrasonic evaluation to detect micro/small surface cracks is the pulse-echo technique using the normal immersion transducer with high frequency, or the angle beam transducer with surface wave. It is difficult to make the automatic ultrasonic system that is to detect micro and small surface crack and position on the large structure like steel and ceramic rolls, because of the huge data of inspection and the ambiguous position data of transducer. The aim of this study using the high precision scanning acoustic microscope with 10MHz large aperture transducer was to display the real time A, B, C-scan for the automatic ultrasonic system in order to detect the existence and position of surface crack. The ultrasonic method with large aperture transducer was improved the scanning time and speed over 10times faster than traditional methods.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.2
• /
• pp.180-185
• /
• 2004

Conventional ultrasonic examination to detect micro and small surface cracks is based on the pulse-echo technique using a normal immersion focused transducer with high frequency, or an angle-beam transducer generating surface waves. It is difficult to make an automatic ultrasonic system that can detect micro and small surface cracks and position in a large structure like steel and ceramic rolls, because of the huge data of inspection and the ambiguous position data of the transducer. In this study, a high-precision scanning acoustic microscope with a 10MHz large-aperture transducer has been used to assess the existence, position and depth of a surface crack from the real-time A, B, C scans obtained by exploiting the ultrasonic diffraction. The ultrasonic method with large aperture transducer has improved the accuracy of the crack depth assessment and also the scanning speed by ten times, compared with the conventional ultrasonic methods.

• Explosives and Blasting
• /
• v.23 no.3
• /
• pp.27-42
• /
• 2005

An explosion modeling technique was developed by using the spherical discrete element code, $PFC^{3D}$, which can be used to model the dynamic stress wave propagation phenomenon. The modeling technique is simply based on an idea that the explosion pressure should be applied to a $PFC^{3D}$ particle assembly not in the form of an external force (body force), but in the form of a contact force (surface force). The stress wave propagation modeling was conducted by simulating the experimental approach based on the Hopkinson's effect combined with the spatting phenomenon that had previously been developed to determine the dynamic tensile strength of Inada granite. As a result, the stress wave velocity obtained by the proposed modeling technique was 4167 m/s, which is merely $3\%$ lower than the actual wave velocity of 4300 m/s for an Inada granite.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.967-972
• /
• 2014

The good light permeability and hardness of glass allow it to be used in various fields. Non-conventional machining methods have been used for glass machining because of its brittle properties. As one non-contact machining method, a laser has advantages that include a high machining speed and the fact that no tool making is required. However, glass has light permeability. Thus, the use of a laser to machine glass has limitations. A nanosecond pulse laser can be used at low power for laser-induced backside wet etching, which is an indirect method. In previous studies, a short-wave laser that had good light absorption but a high price was used. In this study, a near-infrared laser was used to test the possibility of glass micro-machining. In particular, when deeper machining was conducted on a glass structure, more problems could result. To solve these problems, microstructure manufacturing was conducted using ultrasonic vibration.