• Korean Journal of Food Science and Technology
• /
• v.24 no.6
• /
• pp.597-602
• /
• 1992

To improve utilization of boxthorn (Lycii Fructus), the boxthron and mixed boxthron (Lycii Fructus, Schizandrae Fructus, Corni Fructus, Zizyphi Fructus, Zingiberis Rhizoma, Cinnamami Cortex) hot-water extractable concentrates were prepared by vaccum evaporation and its rheological properties were investigated. The rheological properties of concentrates $(20{\sim}50^{\circ}Bx)$ followed power low model and showed a pseudoplastic behavior at the temperature range of $20{\sim}60^{\circ}C$. The apparent viscosity of $20^{\circ}Bx$, $30^{\circ}Bx$, $40^{\circ}Bx$ and $50^{\circ}Bx$ boxthron hot-water extractable concentrate was 0.0074 Pa s, 0.0175 Pa s, 0.0431 Pa s and 0.0988 Pa s, that of mixed boxthorn hot-water extractable concentrate was 0.0099 Pa s, 0.0328 Pa s, 0.0720 Pa s and 0.1940 Pa s at $20^{\circ}C$ and 1500 l/s, respectively. The yield stress of boxthron and mixed boxthron hot-water extractable concentrates ranged from 0.045 to 6.253 Pa and from 0.022 to 8.891 Pa, respectively. The activation energy for the flow of boxthron and mixed boxthorn hot-water extractable concentrates increased from 1.6182 to $2.0543{\times}10^7\;J/kg{\cdot}mol$ and from 1.7057 to $2.1462{\times}10^7\;J/kg{\cdot}mol$ with the concentrations of concentrates, respectively.

• Korean Journal of Food Science and Technology
• /
• v.19 no.6
• /
• pp.499-505
• /
• 1987

The functional properties of lupin seed protein concentrate (LPC) were examined and compared to those of soybean protein isolate (SPI) and Na-caseinate. LPC-50, of which protein level was 50%, was prepared by a two phase solvent (hexane: alcohol: water= 10:7:3) extraction method. LPC-70 was made from LPC-50 by removing the fractions solubilized by carbohydrate decomposing enzymes. The solubilities of LPC-50 and LPC-70 were similar to that of of SPI but slightly higher at pH 4-5, and less susceptible to the added salt. The apparent viscosity of LPC increased exponentially as the concentration increased over 6% level, and the change was similar to that of Na-caseinate. LPC showed strong pseudoplastic non-Newtonean flow behavior, which was similar to that of SPI The emulsifying capasity of LPC-70 was similar to that of SPI when salt was added. The foaming capacity of LPC was comparable to that of SPI. LPC showed high oil and water absorption capacities, which increased as the protein level was elevated. LPC-70 showed the highest oil absorption capacity of all the samples tested.

• Microbiology and Biotechnology Letters
• /
• v.35 no.3
• /
• pp.203-209
• /
• 2007

Soybean milk cake (SMC) was used for the solid-state fermentation by Bacillus subtilis PUL-A isolated from soybean milk cake. In the presence of 5% glutamate the maximum production of biopolymer (59.9 g/kg) was performed by fermentation at $42^{\circ}C$ for 24 hr. The recovered biopolymer was consisted of 87% $\gamma$-polyglutamic acid with molecular weight of $1.3{\times}10^6$ dalton and other biopolymer. The biopolymer solution showed the great decrease in consistency below pH 6.0, regardless of the molecular weight of PGA. Biopolymer solution has a typical pseudoplastic flow behavior and yield stress. The consistency of biopolymer solution was greatly decreased by increasing heating time and temperature in acidic condition compared to the alkaline condition. In kaolin clay suspension, the flocculating activity of biopolymer was the highest value with 15 mg/L biopolymer and 4.5 mM $CaCl_2$, but decreased greatly with $FeCl_3$. The flocculating activity of biopolymer was maximum at pH5, but decreased drastically by heating at $60{\sim}100^{\circ}C$. In particular, biopolymer with native PGA showed the efficient flocculating activity compared to that of modified biopolymer containing low molecular weight of PGA.

• Korean Journal of Food Science and Technology
• /
• v.27 no.4
• /
• pp.582-592
• /
• 1995

To measure rheological properties of the starch dough, an Extrusion Capillary Viscometer(ECV) cell was self-made and attached to Instron machine(Model 1140). Apparent viscosities of corn and waxy corn starch doughs were measured and their gelatinization degrees were determined by enzymatic analysis. When corn and waxy corn starch doughs with $36{\sim}52%$ moisture content were heated at $60{\sim}100^{\circ}C$, come-up time of the cold point of doughs decreased from 220 sec to 140 sec with increased in the moisture content. In the measurement range of $36{\sim}52%$ moisture content and $60{\sim}100^{\circ}C$ heating temperature, both corn and waxy corn starch doughs showed pseudoplastic flow behaviors. At the same shear rate, both shear stress and viscosity of starch dough decreased as the moisture content increased. At the moisture content above 44%, the shear stress and viscosity of starch dough decreased as the heating temperature increased from $60^{\circ}C\;to\;70^{\circ}C$, but increased as the heating temperature increased from $80^{\circ}C\;to\;100^{\circ}C$. When the moisture content increased and heating temperature, the gelatinization degree of starch dough increased from about 10% to about 62%. The gelatinization degree of waxy corn starch dough was $15{\sim}20%$ higher than that of corn starch dough under the same gelatinization conditions. The effects of moisture content on the viscosity of starch dough were examined by Arrhenius equation. As the moisture content increased, viscosity of starch dough decreased. But the effect of moisture content was greater in the range of $80{\sim}100^{\circ}C$ than in the range of $60{\sim}70^{\circ}C$ heating temperature.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.3
• /
• pp.29-46
• /
• 2014

For circular rigid footings with a rough base on sand, combined vertical - horizontal loading capacity was studied by three-dimensional numerical modelling. A numerical model was implemented to simulate the swipe loading and the probe loading methods and an interpretation procedure was devised in order to eliminate the numerical error from the restricted mesh density. Using the Mohr-Coulomb plasticity model, the effect of friction angle was studied under the associated flow-rule condition. The swipe loading method, which is efficient in that the interaction diagram can be drawn with smaller number of analyses, was confirmed to give similar results with the probe loading method, which follows closely the load-paths applied to real structures. For circular footings with a rough base, the interaction diagram for combined vertical (V) - horizontal (H) loading and the inclination factor were barely affected by the friction angle. It was found that the inclination factors for strip and rectangular footings are applicable to circular footings. For high H/V ratios, the results by numerical modelling of this study were smaller than the results of previous studies. Discussions are made on the factors affecting the numerical results and the areas for further researches.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.3
• /
• pp.59-72
• /
• 2014

For circular rigid footings with a rough base on sand, combined vertical - moment loading capacity was studied by three-dimensional numerical modelling. Mohr-Coulomb plasticity model with the associated flow-rule was used for the soil. After comparing the results of the swipe loading method, which can construct the interaction diagram with smaller number of analyses, and those of the probe loading method, which can simulate the load-paths in the conventional load tests, it was found that both loading methods give similar results. Conventional methods based on the effective width or area concept and the results by eccentricity factor ($e_{\gamma}$) were reviewed. The results by numerical modelling of this study were compared with those of previous studies. The combined loading capacity for vertical (V) - moment (M) loading was barely affected by the internal friction angle. It was found that the effective width concept expressed in the form of eccentricity factor can be applied to circular footings. The numerical results of this study were smaller than the previous experimental results and the differences between them increased with the eccentricity and moment load. Discussions are made on the reason of the disparities between the numerical and experimental results, and the areas for further researches are mentioned.

• Journal of the Korean Society of Safety
• /
• v.11 no.4
• /
• pp.143-150
• /
• 1996

This is an explicit-Implicit, finite element analysis for linear as well as nonlinear hygrothermal stress problems. Additional features, such as moisture diffusion equation, crack element and virtual crack extension(VCE ) method for evaluating J-integral are implemented in this program. The Linear Elastic Fracture Mechanics(LEFM) Theory is employed to estimate the crack driving force under the transient condition for and existing crack. Pores in materials are assumed to be saturated with moisture in the liquid form at the room temperature, which may vaporize as the temperature increases. The vaporization effects on the crack driving force are also studied. The Ideal gas equation is employed to estimate the thermodynamic pressure due to vaporization at each time step after solving basic nodal values. A set of field equations governing the time dependent response of porous media are derived from balance laws based on the mixture theory Darcy's law Is assumed for the fluid flow through the porous media. Perzyna's viscoplastic model incorporating the Von-Mises yield criterion are implemented. The Green-Naghdi stress rate is used for the invariant of stress tensor under superposed rigid body motion. Isotropic elements are used for the spatial discretization and an iterative scheme based on the full newton-Raphson method is used for solving the nonlinear governing equations.

• Korean Journal of Environment and Ecology
• /
• v.35 no.2
• /
• pp.115-125
• /
• 2021

This study surveyed the population ecology of Acheilognathus chankaensis (Pisces: Acheilognathinae) in the vicinity of the Churyeongcheon (Stream) and Seomjingang (River) in Jeonbuk, Korea, from February 2006 to May 2007. The survey found the habits mainly in the slow-flowing waters having sand, mud, and gravel bottoms. Age groups estimated by the standard length-frequency distribution of the population indicated that the one-year-olds were 30-46 mm long, the two-year-olds were 47-58 mm long, the three-year-olds were 59-68 mm long, and the four-year-olds were longer than 69 mm. The gonadosomatic index (GSI) and the ratio of ovipositor length/standard length were the highest in March (♀: 12.9%, ♂: 5.0%) and in April (46.3%), respectively. The ratio of mature egg diameters that were 1.6 mm was highest in May (13.2%). The comprehensive analysis of spawning characteristics showed that the spawning season was from March to June with water temperatures in 11.5-22.5℃, and the sex ratio of female:male was 1:1.13. The fecundity in the ovaries and the number of mature eggs were 318±174.5 (50~583) and 220±139.2 (50~406), respectively. The size of the mature eggs was 2.04±0.110 mm on the long axis and 1.55±0.100 mm on the short axis for the study period. Gut contents of A. chankaensis were mainly phytoplankton such as the genera Fragilaria, Synedra, Navicular, Cymbella (Bacillariophyceae), and Cosmarium (Chlorophyceae).

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.557-562
• /
• 1999

The reaction properties of Pd. Pd-Ce and Pd-La catalysts supported on ${\gamma}-Al_2O_3$ were investigated in the oxidation reaction of methane($CH_4$) exhausted from the compressed natural gas vehicle in a U-tube flow reactor with gas hourly space velocity of $72,000h^{-1}$. The catalysts were characterized by X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), BET surface area and hydrogen chemisorption. Pd catalyst prepared by $Pd(NO_3)_2$ as a palladium precursor and calcined at $600^{\circ}C$ showed the highest activity for a methane oxidation. Catalytic activity of calcined $Pd/{\gamma}-Al_2O_3$ in which most of palladium was converted into palladium oxide species was higher than that of reduced $Pd/{\gamma}-Al_2O_3$ in which most of palladium existed in palladium metal by XRD. As increasing the number of reaction cycles in the wide range of redox, the catalytic activity of $Pd/{\gamma}-Al_2O_3$ was decreased and the highly active window became narrower. Lanthanum oxide promoted Pd catalyst, $Pd/La/{\gamma}-Al_2O_3$ showed enhanced thermal stability compared with $Pd/{\gamma}-Al_2O_3$ even after aging at $1000^{\circ}C$, which was ascribed to the role of La as a promoter to suppress the sintering of palladium metal and ${\gamma}-Al_2O_3$ support. Almost all of methane was removed by the reaction with NO at the redox ratio of 1.2 in case of oxygen excluded steam, but that activity was significantly decreased in the steam containing oxygen.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.1
• /
• pp.69-84
• /
• 2023

Despite the continuous installation and regular inspection of waste treatment facilities, complaints about excessive incineration and illegal dumping stench continue to occur at on-site treatment facilities. In addition, field surveys were conducted on the waste treatment facilities currently in operation (6 type) to understand the waste treatment process for each field, to grasp the main operating factors applied to the inspection. In addition, we calculated the material·energy balance for each main process and confirmed the proper operation of the waste disposal facility. As a result of the site survey, in the case of heat treatment facilities such as incineration, cement kilns, and incineration heat recovery facilities, the main factors are maintenance of the temperature of the incinerator required for incineration and treatment of the generated air pollutants, and in the case of landfill facilities Retaining wall stability, closed landfill leachate and emission control emerged as major factors. In the case of sterilization and crushing facilities, the most important factor is whether or not sterilization is possible (apobacterium inspection).In the case of food distribution waste treatment facilities, retention time and odor control during fermentation (digestion, decomposed) are major factors. Calculation results of material balance and energy resin for each waste treatment facility In the case of incineration facilities, it was confirmed that the amount of flooring materials generated is about 14 % and the amount of scattering materials is about 3 % of the amount of waste input, and that the facility is being operated properly. In addition, among foodwaste facilities, in the case of an anaerobic digestion facility, the amount of biogas generated relative to the amount of inflow is about 17 %, and the biogas conversion efficiency is about 81 %, in the case of composting facility, about 11 % composting of the inflow waste was produced, and it was comfirmend that all were properly operated. As a result, in order to improve the inspection method for waste treatment facilities, it is necessary not only to accumulate quantitative standards for detailed inspection methods, but also to collect operational data for one year at the time of regular inspections of each facility, Grasping the flow and judging whether or not the treatment facility is properly operated. It is then determined that the operation and management efficiency of the treatment facility will increase.