• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1992.03a
• /
• pp.47-58
• /
• 1992

탄소성 재료의 파괴에서 최대하중을 계산할 수 있는 방법이 제시되었다. 사용된 재 료상수는 파괴개시인성, 항복강도, 진행된 균열선단에서 열림 변위 증분에 대한 균열성장의 비이고, 계산을 실험결과에 맞추어 재료상수를 결정한다. 이들 상수로 다른 시편의 최대하 중을 계산하는 간단한 방법을 평면변형하의 A572 강(상온)과 4533(B)강(-10C)에 적용하여 기존의 실험결과와 비교하였다. 또한 균열 선단 열림 변위와 J-적분값에 기초한 다른 방법 과 비교·논의되었다.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.8
• /
• pp.27-35
• /
• 2005

Several damages due to large displacement caused by liquefaction have been reported increasingly. Numerical procedures based on effective stress analysis are therefore necessary to predict liquefaction-induced deformation. In this paper, the fully coupled effective stress model called UBCSAND is proposed to simulate pore pressure rise due to earthquake or repeated loadings. The proposed model is a modification of the simple perfect elasto-plactic Mohr-Coulomb model, and can simulate a continuous yielding by mobilizing friction and dilation angles below failure state. Yield function is defined as the ratio of shear stress to mean normal stress. It is radial lines on stress space and has the same shape of Mohr-Columob failure envelope. Plastic hardening is based on an isotropic and kinematic hardening rule. The proposed model always causes plastic deformation during loading and reloading but it predicts elastic unloading. It is verified by capturing direct simple shear tests on loose Fraser River sand.

• Journal of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.785-796
• /
• 2008

Longitudinal elongation develops in reinforced concrete beams that exhibit flexural yielding during cyclic loading. The longitudinal elongation can decrease the shear strength and deformation capacity of the beams. In the present study, nonlinear truss model analysis was performed to study the elongation mechanism of reinforced concrete beams. The results showed that residual tensile plastic strain of the longitudinal reinforcing bar in the plastic hinge is the primary factor causing the member elongation, and that the shear-force transfer mechanism of diagonal concrete struts has a substantial effect on the magnitude of the elongation. Based on the analysis results, a simplified method for evaluating member elongation was developed. The proposed method was applied to test specimens with various design parameters and loading conditions.

• Composites Research
• /
• v.12 no.5
• /
• pp.1-11
• /
• 1999

Cyclic deformation and fatigue behavior of $Al/$Al_2O_3$ metal matrix composites and matrix alloy were studied. Hatigue strength Al/$Al_2O_3$ composites was about 210MPa, and that of Al matrix alloy was 170MPa. Most of the resultant displacement due to permanent plastic deformation occurred in less than the first 5% of fatigue life. In case of composites, decrease of cyclic displacement was smaller than that of matrix because the reinforcements acted as barriers to dislocation movement. Consequently, cyclic stress-displacement response curve can be considered to have these atages ; an initial few cycles of rapid hardening, followed by progressive hardening for most the fatigue life, and then just prior to failure, an instantaneous drop in stress carrying capability of the material due to multiple microcrack initiation, eventual coalescence of microcrack to form a macrocrack and then rapid macroscopic crack growth.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.833-841
• /
• 2010

In this report, the test results of five reinforced concrete beam-column joint subjected to cyclic load are presented. The main purpose of the research is to investigate the influence of the steel pull-out of the beam-column joints to the shear and ductile capacity of the RC beam-column assembles. In addition, the influence of the amount of beam reinforcement to the joint shear and ductile capacity is evaluated. Test results indicate that the yield penetration of steel bar increases as the joint shear strength ratio, $V_{j1}/V_{jby}$ decreases. And the slippage of the steel bars are varied according to the region of the beam-column joints. The pull-out of the steel bars of five specimens was almost the same regardless of the joint shear strength ratio, $V_{j1}/V_{jby}$. Because it was affected by not only the yield penetration of steel bar but also the axial elongation in the plastic hinge.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.146-152
• /
• 2018

In this study, to improve the performance of asphalt mixtures for plastic deformation occurring mainly in Korea, complex modifiers were prepared by mixing powders and liquid type modifiers. The main constituents were powdery diatomaceous earth, mica and carbon black, and liquid type solid 70% SBR latex. The tensile strength ratios for the two asphalt mixtures used in the test were above 0.80 for the Ministry of Land Transportation (2017) asphalt mixture production and construction guidelines. The effects of increasing the tensile strength in the dry state was more than 14% when the composite modifier was added. The deformation rate per minute by the wheel tracking test load was an average of 0.07 to 0.147 for each mixture. The strain rate per minute was improved by the modifier, and the dynamic stability was improved by almost 100% from 295 to 590. In addition, the final settling was reduced from 11.38 mm to 9.57 mm. A plastic deformation test using the triaxial compression test showed that the amount of deformation entering the plastic deformation failure zone at the end of the second stage section and in the third stage plastic deformation section was 1.76 mm for the conventional mixture and 1.50 mm for the complex modifier mixture. The average slope of the complex modifier asphalt mixture mixed with the multi-functional modifier was 0.005 mm/sec. The plastic deformation rate is relatively small in the section where the road pavement exhibits stable common performance, i.e. the traffic load.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.4
• /
• pp.86-91
• /
• 2001

In lateral ground flow, slope stability, and land slide problems, H-piles have been often used for a horizontally deforming ground to prevent the failure of mass of soil in a downward and outward movement of a slope. Here, Theoretical equations are derived to estimate the lateral force, assuming that the Mohr-coulomb's Plastic states occures in the ground just around H-piles. In this study, the mechanism of lateral force acting on passive pile that is in a row, situated in the ground undergoing plastic deformation was discussed, and its theoretical analysis was carried out considering the interval between H-piles. The solution of the theoretical equation derived from here showed resonable characteristic for constants of soil as well as for the interval, widths, and heights of H-pile.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.190-193
• /
• 2004

Ever since the ideal forming theory has been developed fur process design purposes, application has been limited to sheet forming and, for bulk forming, to two-dimensional steady flow. Here, application for the non-steady case was performed under the plane-strain condition based on the theory previously developed. In the ideal flow, material elements deform following the minimum plastic work path (or mostly proportional true strain path) so that the ideal plane-strain flow can be effectively described using the two-dimensional orthogonal convective coordinate system. Besides kinematics, for a prescribed final part shape, schemes to optimize a preform shape out of a class of initial configurations and also to define the evolution of shapes and boundary tractions were developed. Discussions include the two problematic issues on internal tractions and the non-monotonous straining. For demonstration purposes, numerical calculations were made for a bulk part under forging.

• Transactions of Materials Processing
• /
• v.1 no.2
• /
• pp.52-62
• /
• 1992

본 연구에서는 모델재료를 이용한 모사실험을 통하여 고온의 강을 단조하였을 때의 유동과 변형 그리고 하중을 검토하고, 이어 성형에 관한 연구를 하였다. 모델재료인 플라스티신은 고용의 강을 모사하는데 많이 쓰이는데, 실험을 통하여 플라스티신과 강과의 변형저항식을 비교 검토하였다. 이 실험결과 상사성이 어느정도 일치함을 알았고, 이 상사성 결과를 이용하여 실제와 모델사이의 하중과 응력비를 검출하였다. 이로써 플라스티신을 이용한 단조 압축 실험을 통하여 실제의 하중을 예측하였다. 또한 예비 성형체를 설계하기 위하여 앞서 실험한 결과들을 이용하여 초기의 실린더의 체적과 치수를 결정하고 이에 단계에 따른 성형과정을 통하여 예비 성형체를 만들었는데, 이는 제한된 용량으로 성형하여야 하는 문제를 해결하기 위함이었다. 실험 결과 8단계에 따른 성형과정에 의해 우리가 원하는 대형 단조품을 성형할 수 있음을 알았다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.659-665
• /
• 1995

액체금속로는 기존의 가압경수로와는 달리 55$0^{\circ}C$ 정도의 고온에서 운전이 되므로 고온 열응력이 중요한 문제로 대두되며 따라서 고은에서의 크립(Creep) 변형, 반복되는 기동과 정지 등으로 인한 되풀이 소성변형, 라체팅(Ratchetting), 크립과 소성의 상호작용 및 크립과 피로의 상호작용 등의 평가에 대한 기술 확립과 고온구조물에 대한 우리의 독자적인 설계방법을 개발하는 것이 필요하다 본 연구에서는 범용 유한요소해석코드인 ABAQUS의 축대칭 요소를 이용해서 액체 금속로 원자로용기와 이에 부착된 열소매(Thermal sleeve)를 Y-형태의 구조물로 모델링하여 반복되는 열천이하중에 대한 비탄성 구조해석을 수행하고 크립효과에 대한 영향을 분석하였다. 해석결과 액체금속로와 같은 고온구조물에 대하여 반복 열천이 하중과 고온 지속시간이 유발하는 크립효과가 크게 나타남을 알 수 있었다.