• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.360-365
• /
• 1992

Ga-doped polycrystalline ZnO films on glass substrates were prepared by sputtering the targets, which had been prepared by sintering discs consisting of ZnO powder and various amounts of G$a_2O_3$, to investigate the effects of gallium doping and sputtering conditions on electrical properties. Optimizing the RF power density, argon gas pressure and gallium content, transparent Ga-doped ZnO films with resistivity less than 1$0^{-3}$ohm-cm are obtained. Electron concentration of undoped and Ga-doped ZnO films are order of $10^{18}$, $10^{21}$/c$m^2$respectively. After heat treatment in air and $N_2atmosphere, $ the resistivity of Ga-doped ZnO films increases by about two orders of magnitude. The optical transmission is above 80% in the visible range and the optical band widens as the Ga content increases.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.269-275
• /
• 2021

In this study, ordered mesoporous silica-supported Ni catalysts were prepared for catalytic partial oxidation of methane (CPOM) by using electroless nickel plating method. Unlike conventionally impregnated catalysts, the electrolessly-plated nickel catalyst showed that nickel was highly dispersed and formed stably on silica-supported surface. It was verified by TEM-EDS analysis. During the activity tests, the electrolessly-plated nickel was barely sintered and the amount of carbon deposition was very small. Consequently, the catalyst was far less deactivated, while the sintering was significantly observed in the cases of the catalysts prepared by the conventional impregnation method. Regarding the palladium-promoted catalysts, the reducibility of nickel was increased, and the reaction performances were enhanced in terms of CH4 conversion and H2/CO ratio of produced syngas.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.2
• /
• pp.66-72
• /
• 2020

The difference of plasma resistance between the CAS glass bulk and coating films were compared. Plasma resistance was confirmed by analyzing the etch rate and the microstructure of the surface when the CAS glass bulk and the glass coating film were etched with CF₄/O₂/Ar plasma gas. CAS glass coating film was etched up to 25 times faster than the glass bulk. A statistically high correlation between the surface roughness and the etching rate of the coating film was derived, and thus, the high surface roughness of the coating film was determined to cause rapid etching. In addition, cristobalite crystals that has a low Ca content and a high Si content, was foamed on the glass coating film. Therefore, the CAS glass coating film is considered to have low plasma resistance compared to the glass bulk.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.2
• /
• pp.69-74
• /
• 2007

[ $0.6Pb(Sc_{1/2}Ta_{1/2})O_3-0.4PbTiO_3$ ] (hereafter PSTT) ceramics were prepared by the molten salt synthesis (MSS) method using KCI as a flux. Formation of perovskite phase was investigated by a differential thermal analysis (DTA) and X-ray diffraction (XRD) analysis in the temperature range from $600^{\circ}C$ to $850^{\circ}C$. A 92% perovskite phase was synthesized at $750^{\circ}C$ for 2 hrs using the MSS method, while 82% perovskite phase was synthesized at $850^{\circ}C$ for 4ks using the calcining of mixed oxide (CMO) method. This result could be due to the improvement in reactivity of $Sc_2O_3$ by melting of KCI. The MSS specimen sintered at $1,100^{\circ}C$ for 4hrs showed a dielectric constant of 11,200, a remnant polarization of $13.5{\mu}C/cm^2$ and a coercive field of 10.198 kV/cm, which was discussed in view of the microstructure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.11
• /
• pp.2573-2584
• /
• 1997

In this paper, Ca, Sn substitute YIC(Yttrium Iron Garnet) ceramics were fabricated with Al substitutions in Fe sites. The strip-line circulator was designed and the properties of fabricated ciculator were measured. When the electric, magnetic and microwave properties were measured in Ca, Sn substituted YIG with Al subsititions, the relative permittivity and perfmeability in microwave frequencies were 15.623 and 0.972, repectively. For $Y_{2.4}Ca_{0.3}Sn_{0.3}Fe_{5-x}Al_xO_{12}$ garnet ceramics sintered at $1450^{\circ}C$, the ferrimagnetic resonance line width $\Delta{H}$) of 42 Oe and the saturation magnetization of 487 G were measured at 10 GHz. The strip-line circulator was simulated with 3-D FEM(Finite Element Method) software and designed to have insertion loss of 0.8dB, return loss of 25dB, isolation of 35dB at the center frequency of 1.9GHz. The fabricated strition loss of 0.8B, reture loss of 25dB, isolation of 35dB at the center frequency of 1.9GHz. The fabricated strip-line junction circulator using above YIG ceramics had insertion loss of 0.869dB, return loss of 26.955dB, isolation of 44.409dB at the center frequency of 1.9GHz.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.503-510
• /
• 2002

Silicon carbide candle filters for the pressurized fluidized bed combustion system were fabricated by extrusion process. Carbon black was added to control the porosity. Inorganic additives such as clay and calcium carbonate were added to exhibit appropriate strength. Silicon carbide layer with a finer pore size (mean pore diameter ~$10{\mu}m$) was coated on the silicon carbide support layer (mean pore diameter ~$47{\mu}m$, porosity ∼40%). After that, the filter was sintered at 1400${\circ}C$ in air. We evaluated the filtration performances of the filter at 500${\circ}C$ and $5kgf/cm^2$ of pressure. As a result, high separation efficiency, >99.999% was measured. It is expected that silicon carbide candle filter can be successfully used for the pressurized fluidized bed combustion system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.3
• /
• pp.139-146
• /
• 2012

Natural hydroxyapatite powder was obtained from the calcination of bovine bones and its porous compacts were fabricated by pressureless sintering at 1100 and $1200^{\circ}C$ for 1h. To evaluate and compare their biocompatibility with porosity, we investigated the support of osteoblast cells growth and cytotoxicity using the MG-63 cell line model in vitro. Sintered hydroxyapatite ceramics have a porous microstructure with a relative density of 65 % at $1100^{\circ}C$ and 82 % at $1200^{\circ}C$. Cells adherence to the surface of hydroxyapatite ceramics was observed in a day after the cell culture, and the spreading of cytoplasm around the nucleus was shown after 3 day cell culture. Most of cells were extended to the surface of hydroxyapatite through the wide area. Cell viability was nearly the same till 3 days culturing. But the rate of cell growth is higher in the specimen sintered at $1100^{\circ}C$ than that of $1200^{\circ}C$. It indicates that the porosity is an important factor to enhance the cell viability in the porous hydroxyapatite ceramics derived from bovine bones.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.371-383
• /
• 2009

Crystallinity and textural relations, which are crucial in terms of the quality concept of high-purity limestone, have not been effectively applicable to the limestone evaluation as crude ore due to the difficulties in precise measurements. To overcome the above, as a new method of ore characterization, a measurement of shape factor and grain boundary frequency utilizing the image analysing system was adopted in this study. Some domestic limestones used for lime manufacturing were investigated by such a quality evaluation method, and its results are discussed and correlated each other samples. As the result, even though calcite contents of crude ore, i.e., limestone grade and its crystal size are similar, quality of manufactured lime is remarkably different depending on the degree of shape factor and grain boundary frequency. In other words, as the more irregular in crystal shape and the higher the grain boundary frequency, the manufactured quick lime became more superior in all terms of lime quality such as rate of calcination, porosity, reactivity, sintering and decrepitation effect. However, because the quick lime become easily overheated in case of relatively higher degree in shape factor and grain boundary effect, a technology minimizing heating time is necessary for the manufacturing of high quality lime. In limestone industry, such a ore characterization method will be much more reasonable than the conventional method by measurement of mean size, because the method may collectively comprise crystal shape and other textural factors which can not be numerically evaluated in the past.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.26-36
• /
• 2018

Conventional nickel-based catalyst processes used for dry reforming reactions have high activation temperatures and problems such as carbon deposition and metal sintering on the active sites of the catalyst surface. In this study, the characteristics of butane dry reforming reaction were investigated by using DBD plasma combined with catalytic process and compared with existing catalyst alone process. The physical and chemical properties of the catalysts were investigated using a surface area & pore size analyzer, XRD, SEM and TEM. Using $10%Ni/{\gamma}-Al_2O_3$ at $580^{\circ}C$, in the case of the catalyst+plasma process, the conversion of carbon dioxide and butane were improved by about 30% than catalyst alone process. When the catalyst+plasma process, the conversion of carbon dioxide and butane and the hydrogen production concentration are enhanced by the influence of various active species generated by the plasma. In addition, it was found that the particle size of the catalyst is decreased by the plasma in the reaction process, and the degree of dispersion of the catalyst is increased to improve the efficiency.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.261-271
• /
• 1993

Functionally Gradient Materials(FGM) of 4.5Pb($Ni_{1/3}Nb_{2/3})O_3$-55PZT and PLZT(lO/70 /30, 11/60/40) were prepared. Its dielectric and piezoelectric strain properties were investigated. The FGM were pressed into A/B/ A configuration using two kinds of films, one layer(A) was eliminated from FGM by polishing after sintering at $l250^{\circ}C$, 2 hrs. The acrylic binder system was successfully applied for crack free film through doctor blade method. The thickness of gradent layer in FGM was about 30${\mu}$m. Dielectric properties of FGM show the average value of each side layer. The strain-electric field characteristics of FGM were significantly improved comparison with the other single compositions. The prepared FGM piezoelectric actuator shows about 3${\mu}$m/IOOV displacement.