• 연구논문집
• /
• s.30
• /
• pp.111-119
• /
• 2000

Sintering of alumina powder was studied in the presence of Y-Si oxide and oxynitride additives. The main crystalline phase of the sintering aids pre-reacted at $1400^{\circ}C$ was $\alpha$ - $Y_2$$SiO_2$>$O_7$. Y-N apatite was co-existed in the Si-40N sintering aid because of its high content of N. During the sintering process, liquid phases were formed by the reaction between additives and alumina, and these liquid phases promote the densification of alumina. SEM micrographs showed that uniform grain growth occurred in the system with oxide additive(Si-0N). In the case of oxynitride additive system(Si-20N and Si-40N), bimodal microstructure was observed due to the exaggerated grain growth, As the nitrogen content in the additive system increased the exaggerated grain growth occurred extensively. Bloating, which seemed to be originated by the liberation of $N_2$ gas, occurred un the Si-40N oxynitride additive system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.508-512
• /
• 1998

The NTC thermistors were sintered by using microwave hybrid heating method at $1100^{\circ}C$~$1300^{\circ}C$ and those electrical properties were investigated. The obtained $B_{25^{\circ}C/85^{\circ}C}$ values from temperature dependence of electrical resisitivity were around 3100~3200 K which were almost the same values as conventionally sintered ones. Compared with conventional sintering process, this process could complete whole sintering process within 20 minutes. This the processing time and energy consumption could be reduced through this rapid heating by using microwave hybrid heating.t there were showed only two peaks, glycolide melting peak and lower molecular weight melting peak without lauryl alcohol. Conversion increased slowly with the reaction time up to 50 minutes, and then gave a sudden increase above that. The reaction time to disappear in glycolide melting peak during polymerization was shortened with the increase of lauryl alcohol content. Zero-shear viscosity of polyglycolic acid decreased with the increase of free acid content in glycolide.ssional energy and bending hysteresis increased. \circled3 Surface characteristics such as friction coefficient and thickness variation of highly shrinkage fabrics became relatively roughened state. \circled4 Since stiffened and roughened characteristics of highly shrinkage fabrics, drapabilities of them were significantly lowered. Additionally thermal insulation property of high shrinkage fabric was higher than that of low shrinkage fabric due to bulky and thickened feature. From the results, it is considered that the silk fabrics with high filling shrinkage have the good bulkiness and heat keeping properties and thus they have the suitable characteristics for high quality men's and women's formal garments.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.1
• /
• pp.28-37
• /
• 2018

In order to study the NTC thermistor that can be fired at low temperature, the influence of the lead free glass frit and $RuO_2$ addition on the electrical properties of the NTC thermistor of $Mn_{1.85}Ni_{0.25}Co_{0.9}O_4$ basic composition was studied. The sintering characteristics of the specimen sintered at $1000^{\circ}C$ with 10 wt% frit added to the basic NTC composition were similar to those of the specimen sintered at $1200^{\circ}C$ without frit. However, as the amount of frit increased, the electrical resistivity and B constant were increased. In order to reduce the resistance, NTC thermistor was prepared by adding 0, 2, and 5 wt% of $RuO_2$ to the composition containing 10 wt% of frit and sintered at $1000{\sim}1200^{\circ}C$, and sintering and electrical properties were measured. The electrical resistivity and the B constant tended to decrease with increasing $RuO_2$ content. However, the resistivity was the lowest at sintering temperature of $1000^{\circ}C$ and the resistance increased with increasing sintering temperature after 5 wt% $RuO_2$ addition. The NTC thermistor sintered at $1000^{\circ}C$ with 10 wt% frit and 5 wt% $RuO_2$ in the composition of NTC showed similar electrical properties and sintering characteristics when sintered at $1200^{\circ}C$ without added frit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.6
• /
• pp.468-472
• /
• 2005

In order to prevent adhering of molten glass on a mold wall, the wall is swabbed with lubricant oil before forming. However, the swabbing process can be removed from the entire processes of the glass forming if the mold wall is made of a porous sintered material. The purpose of the present study is to manufacture a sintered material(having a sintered density of $85{\~}90\%$)which is the most appropriate into. plane material for a glass mold. For the research, SUS310L-based coarse powder (${\~}150{\mu}m$) and SUS420J2-based fine powder ($40{\~}50{\mu}m$) were used for the compact materials, and effects of compaction pressure and sintering condition(atmosphere, temperature) were investigated. The results obtained were as fellows. (1) By means of solid phase sintering, a desired sintering density could not be achieved in any case when using a 310L-based powder having a large particle size. (2) When sintering green compacts(compaction pressure of $2ton/cm^2$) in a commercial vacuum furnace(at $1300^{\circ}C$ for 2 hours), the sintered compacts had densities of $6.2g/cm^3(79\%)$ for 310L + 0.03$\%$B, $6.6g/cm^3 (86\%)$ for 420J2, $7.3g/cm^3(95\%)$ for 420J2+(0.03)$\%$B, and $7.6g/cm^3(99\%)$ for 420j2+(0.06)$\%$B, respectively. As a result, it is regarded that sintered compacts having a desired porosity may be achieved by vacuum sintering the 420J2-based powder (low pressure compaction) and the 310L+0.03$\%$B-based powder (high pressure compaction).

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.284-292
• /
• 1999

고체함량을 변화시킨 NiCuZn 페라이트 페이스트를 사용하여 스크린 인쇄법으로 7.7$\times$4.5$\times$1.0 nm 크기의 칩인덕터를 제조한 후, 페라이트 페이스트의 고체함량에 따른 수축률, 소결밀도, 미세구조, 계면반응 등의 물리적 특성 및 자기적 특성 변화를 분석하였다. 조온소결을 위하여 attrition milling 공정을 통하여 미세분말을 준비하였으며, 소결온도는 880~94$0^{\circ}C$로 변화시켰다. 90$0^{\circ}C$에서 2시간 열처리된 페라이트 후막의 소결밀도는 고체함량이 50,55,60%로 증가할수록 5.12,5.14,5.18g/㎤로 증가하였으며, 이에 따라 칩 인덕터 시편들의 주파수 10 MHz에서 L값이 2.1,2.3,2.5 $\mu$H로 커졌다.Q값은 소결밀도 증가에 의한 Q값 증가효과와 아울러 입자가 커짐에 따른 반대효과로 인하여 고체함량에 따라 87,90,94로 큰 변화가 없었다. 페라이트 페이\ulcorner의 고체함량 및 소결온도와 무관하게 Ag 성분의 페라이트 쪽으로의 확산현상은 나타나지 않았다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.194-194
• /
• 2003

지르콘은 내침식성, 내마모성, 열 충격 저항성 및 기계적 물성이 우수하여 내화재료, 연마재료 등으로 다양하게 활용된다. 이러한 지르콘의 물성은 출발원료의 입도와 순도, 첨가제, 열처리 온도 등에 크게 의존한다. 본 연구에서는 출발 물질의 평균 입도를 각각 5$\mu\textrm{m}$와 3$\mu\textrm{m}$, l$\mu\textrm{m}$ 이하로 제어하였고, 시료의 열처리 온도를 135$0^{\circ}C$, 140$0^{\circ}C$, 145$0^{\circ}C$, 150$0^{\circ}C$, 155$0^{\circ}C$로 소결하였다. 각각의 지르콘 소결체는 미세 경도 측정, 결정상 분석, 밀도 측정, 미세구조 관찰을 통하여 특성 평가하였다. 미세경도 값은 140$0^{\circ}C$에서 소결된 지르콘의 가장 높았으며, 밀도는 150$0^{\circ}C$에서 소결된 지르콘이 가장 높으며, 155$0^{\circ}C$에서 소결된 지르콘은 과소결되어 전체적으로 물성이 저하되는 것을 관찰하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.6
• /
• pp.11-15
• /
• 1979

Electrical switching phenomenon was observed in the Fe2O3-Bi2O3 system for the sintering temperature range of 700$^{\circ}$~85$0^{\circ}C$ for DC conductivity measurements of these sinterd materials in the ambient temperature range of 30$^{\circ}$~20$0^{\circ}C$ have shown that the conductivity increases with increasing the sitering temperature and ambient temperature. The formation of the current channel and the experimental evidence of the dependence of switching threshold voltage on the ambient temperature, strongly indicates that the main electrical switching mechanism of sintered Fe2O3-Bi2O3 is thermal effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.323-323
• /
• 2010

PNN-PZT계 세라믹스를 $Pb(Ni_{1/3}Nb_{2/3})_{0.4}(Zr_{0.48}Ti_{0.52})_{0.6}O_3$ 조성으로 설계하고, 이에 낮은 융점의 NiO를 1wt% 첨가하여 저온소결 특성을 평가하였다. 일반적인 세라믹 분말 소결법을 이용하여 시편을 제작하였으며, 이때의 소결온도는 $850{\sim}105^{\circ}C$ 범위에서 변화시켰다. 소결체의 압전 및 유전적 특성을 평가를 하고. SEM 및 XRD를 이용한 미세구조 및 상 분석도 수행하였다. 이러한 실험 결과, PNN-PZT 세라믹은 NiO의 첨가로 $1000^{\circ}C$ 정도에서도 저온소결이 가능한 것을 확인하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.2
• /
• pp.1-6
• /
• 1998

B2O3F2를 함유한 Fluormica glass-ceramics 분말과 Potashborosilicate glass 분말을 이용하여 저온소결용 기판을 제조하기 위하여 제조한 그린시트의 특성 및 소결체의 소결 특 성을 평가하였다. 기판 제조용 슬러리를 제조하기 위해 결정화유리분말에 Potashborosilicate glass 분말을 각각 0. 25, 50wt%를 혼용하였다. Doctor blade법으로 그린시트를 제조한후 그 특성을 평가한 결과 건조수축률은 15.2~30.7% 온도상승에 따른 유기물의 탈지온도는 414$^{\circ}C$(2시간)로 선정하였다. 그린시트는 800~120$0^{\circ}C$사이에서 소성하여 소결특성을 평가하였 다. 소결 수축률은 17.5~18.5% 겉보기 기공률은 16.53~20.07%였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.91.2-91.2
• /
• 2011

고체산화물 연료전지의 연결재의 필요한 물성으로는 공기극과 연료극을 차폐시켜줄 수 있는 고밀도와 구성 소재간의 전기적으로 연결될 수 있는 전기전도도 및 낮은 이온전도도. 산화극과 환원극에서 화학적 안정성과 타 구성 소재와의 열팽창 계수가 일치 등이 중요한 특성으로 필요하게 된다. 이를 위해 LaCrO3계 연결재가 주로 사용되어 왔다. 그러나 LCO계 연결제는 $1400^{\circ}C$ 이상의 높은 소결 온도와 이로 인한 Cr의 휘발로 인한 타 구성소재와의 반응 등으로 인해 저온소결의 필요성이 재기되고 있는 소재 이다. 본 연구에서는 LCO계 구성 소제에 소결 조제를 첨가하여 저온에서 결정성 및 소결거동, 전기적 특성을 평가하였다.