• Journal of the Korean GEO-environmental Society
• /
• v.13 no.10
• /
• pp.25-32
• /
• 2012

The application of electrical resistivity, which is related to charge mobility, has increased in the field of geotechnical engineering for the detection of underground cavern, faults and subsurface pollution level. The purpose of this study is to investigate the variation of electrical resistivity due to temperature change. Sand-silt mixture specimens prepared in the square freezing nylon cell are frozen in the frozen chamber. Four electrodes are attached on the four side walls of the freezing cell for the measurement of electrical resistance during temperature change. Electrical resistances of sand-silt mixtures with different degrees of saturation (0%, 2.5%, 5%, 10%, 20%, 40%, 60% and 100%) are measured as the temperature of specimens decrease from $20^{\circ}C$ to $-10^{\circ}C$. The electrical resistances determined by Ohm's law are transformed into the electrical resistivity by calibration. Experimental results show that the higher degree of saturation, the lower electrical resistivity at $20^{\circ}C$. Electrical resistivity gradually increases as the temperature decrease from $20^{\circ}C$ to $0^{\circ}C$. For the specimens with the degree of saturation of 15% or higer, electrical resistivity dramatically changes near the temperature of $0^{\circ}C$. In addition, very high electrical resistivity is observed regardless of the degree of saturation if the specimens are frozen. This study provides the fundamental information of electrical resistivity according to the soil freezing and temperature change demonstrates that electrical resistivity be a practical method for frozen soil investigation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.1
• /
• pp.80-90
• /
• 1996

The efficienty of ATM is based on the statical multiplexing of fixed-length packets, which are called cells. The most important technical point for realizing ATM switching network is an arrangement of the buffers and switches. Current most ATM switching networks are being achieved by using the switching modules based on the unit switch of $8{\times}8$ 150Mb/s or $16{\times}16$ 150Mb/s, the unit switch of $32{\times}32$150Mb/s for a large scale system is under study in many countries. In this paper, we proposed a new $32{\times}32$(4.9Gb/s throughput) ATM switch using Shared buffer memory switch which provides superior traffic characteristics in the cell loss, delay and throughput performance and easy LSI(Large Scale Integrated circuit). We analytically estimated and simulated by computer the buffer size into it. We also proposed the configuration of the large capacity ATM switching network($M{\times}M$.M>1,000) consisting of multistage to improve the link speed by non-blocking.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.172-177
• /
• 2014

We present on a threshold switching device based on AsGeTeSi material which is significantly improved by two $N_2$ processes: reactive $N_2$ during deposition, and $N_2$ plasma hardening. The introduction of N2 in the two-step processing enables a stackable and thermally stable device structure, is allowing integration of switch and memory devices for application in nano scale array circuits. Despite of its good threshold switching characteristics, AsTeGeSi-based switches have had key issues with reliability at a high temperature to apply resistive memory. This is usually due to a change in a Te concentration. However, our chalconitride switches(AsTeGeSiN) show high temperature stability as well as high current density over $1.1{\times}10^7A/cm^2$ at $30{\times}30(nm^2)$ celll. A cycling performance of the switch was over $10^8$ times. In addition, we demonstrated a memory cell consisted of 1 switch-1 resistor (1S-1R) stack structure using a TaOx resistance memory with the AsTeGeSiN select device.

• Polymer(Korea)
• /
• v.29 no.3
• /
• pp.308-313
• /
• 2005

The effects of molecular environments on photoisomerization of an azobenzene group were investigated using In-situ UV/Vis spectroscopy and optical anisotropy measurement technique. The reversible and repeatable photoisomeritation reactions of azobenzene were observed by irradiating the film containing 4-hydroxyazobenzene and by measuring absorption intensities of the characteristic bands of trans and cis isomers simultaneously. When the self-assembled monolayer with azobenzene groups was used as an alignment layer for a liquid crystal cell, the homeotropic alignment was induced due to their compact packing structures of azobenfene groups along the vertical direction of the substrate. By irradiating UV light on this cell, the trans-azobenzene groups change to cis-isomers through the photoisonlerieation and then resulting in the planar alignment of liquid crystal molecules.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.474-482
• /
• 2016

A Kelvin foam plate - widely used in the energy and transport industries as a lightweight structural material - was examined to estimate its Young's modulus using ultrasound. An isotropic tetrakaidecahedron foam structure was designed in SolidWorks and printed using 3D printer with an ABS plastic material. The 3D printed foam structure was used to build a foam plate with a 14 mm thickness ($50mm{\times}100mm$ in size) for the ultrasonic test. The Kelvin foam plate, a significantly porous medium, was completely filled with paraffin wax to enable the ultrasound to penetrate through the porous medium. The acoustic wave velocity of the wax-filled Kelvin foam was measured using the time of flight (TOF) method. Furthermore, the elastic modulus of the Kelvin foam was estimated based on an elastic structural model developed in this study. The Young's modulus of the produced Kelvin foam was observed to be approximately 3.4% of the bulk value of the constituent material (ABS plastic). This finding is consistent with experimental and theoretical results reported by previous studies.

• Journal of the Korean Magnetics Society
• /
• v.27 no.2
• /
• pp.49-53
• /
• 2017

Metamaterials composed of split cut wire (SCW) on grounded polyimide film substrate have been investigated for the aim of electromagnetic wave absorbers operated in THz frequency band. Reflection loss and current density distributions are numerically simulated with variations of the SCW geometries using the commercial software. The minimum reflection loss lower than -20 dB has been identified at 5.5~6.5 THz. The simulated resonance frequency and reflection loss can be explained on the basis of the circuit theory of an inductance-capacitance (L-C) resonator. Dual-band absorption can be obtained by arrangement of two SCWs of different length on the top layer of the grounded substrate, which is due to multiple magnetic resonances by scaling of SCWs. With increasing the side spacing between SCWs, a more enhanced absorption peak is observed at the first resonance frequency that is shifted to a lower frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.7B
• /
• pp.647-659
• /
• 2003

LPM(Longest Prefix Matching)searching in If address lookup is a major bottleneck of IP packet processing in the high speed router. In the conventional lookup table for the LPM searching in CAM(Content Addressable Memory) the complexity of fast update take 0(1). In this paper, we designed pipeline architecture for fast update of 0(1) cycle of lookup table and high throughput and low area complexity on LPM searching. Lookup-table architecture was designed by CAM(Content Addressable Memory)away that uses 1bit RAM(Random Access Memory)cell. It has three pipeline stages. Its LPM searching rate is affected by both the number of key field blocks in stage 1 and stage 2, and distribution of matching Point. The RTL(Register Transistor Level) design is carried out using Verilog-HDL. The functional verification is thoroughly done at the gate level using 0.35${\mu}{\textrm}{m}$ CMOS SEC standard cell library.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.12
• /
• pp.2427-2433
• /
• 2015

A high-gain circularly-polarized patch antenna with a double-layered superstrate is proposed operating at a wireless LAN frequency. A superstrate has an array of metallic periodic unit cells and is located above the patch antenna with an air-gap. The designed antenna has a high gain of over 9.59dBi, which is the gain enhancement of 6.48dB compared to the patch antenna without superstrate. And it has a low axial ratio of under 3dB, so that it maintains the circular polarization of the patch antenna. The optimum air-gap height at the superstrate of $4{\times}4$ arrays is 25mm, which is equivalent to about $0.2{\lambda}$ at the frequency of 2.45GHz. We confirmed that the double-layered stacking of a superstrate increases the effective aperture size and hence it leads to enhance a gain of the patch antenna.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.3 no.2
• /
• pp.39-45
• /
• 2010

In this paper, an equally spaced $3{\times}2$ microstrip patch array antenna based on the fundamental infinite wavelength supported by the composite right/left-handed (CRLH) transmission line (TL) is proposed. The proposed CRLH TL unit cell consists of an inter-digit capacitor to realize left-handed (LH) series capacitance and non-symmetric shunt meander line with a shorted via to realize LH shunt inductance. At the infinite wavelength frequency of 2.09 GHz a 6-port series power divider consisting of a 19 unit cells shows a maximum magnitude difference of 0.73 dB and a $0.52^{\circ}$ maximum phase difference between output ports. The measured resonant frequency and maximum gain of the fabricated array antenna is 2.09 GHz and 10.98 dBi, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.9A
• /
• pp.749-754
• /
• 2005

It is well-known that mobile communication systems are usually limited in their performance and capacity by three major impairments, which are multipath fading, delay spread and co-channel interference (CCI). OFDMA (OFDM-FDMA) system can cope with the multipath fading and delay spread easily due to the beneficial properties of OmM technology. Though OFDMA scheme avoids intra-cell interference using the orthogonality among subcarriers, the scheme contains difficulty of reducing co-channel interference. Therefore, in this paper, adaptive antenna techniques are deployed into OFDMA/TDD system to minimize the co-channel interference induced by adjacent cells and to enhance the uplink performance. For the improvement of downlink performance, we apply TxAA (Transmit Adaptive Array), a kind of transmit diversity technique, utilizing preamble symbols for training antenna may into OFDMA/TDD transmitter side. Simulation results show that the uplink and downlink performance under multipath Rayleigh fading channel improved 9dB and 7dB each compared with the case of single antenna system at target BER $10^{-3}$ .