• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.23-24
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.243-244
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.355-356
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.53-54
• /
• 2011

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.122-129
• /
• 2008

This paper deals with precise positioning of a high-speed positioning stage without inducing residual vibration by using an input shaping technique. Input shaping is well known to be a very effective tool for suppressing the residual vibration of flexible structures. However, the ordinary input shaping for positioning stages is designated mostly for velocity regulation, not for the residual vibration at the target position. The main difficulties in implementing input shaping along with precise positioning are the time delay caused by the servo system characteristics and the s-curve feature often employed in some motor controllers. This paper analyzes the dynamic responses of a single-mode-dominate stage system subjected to input shaping. A theoretical model is developed io investigate the nature of system. In order to overcome the difficulty, this paper proposes an improved input shaper based on modified command profile generation. The proposed method is proved effective through experiments and simulations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.701-706
• /
• 2012

This research is concerned with the derivation of equations of motion for a slewing beam and the application of input shaper to the bang-bang control to achieve vibration suppression. When a uniform beam with a tip mass rotates about the axis perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates. In this paper, we used the input shaper for the maneuvering control to suppress vibrations. The maneuvering control which can achieve a minimum-time control is a bang-bang control. The input-shaped bang-bang maneuvering is used to suppress vibrations both theoretically and experimentally. The slewing beam experiment is not an easy subject because of the inherent damping existing inside the rotor. We propose the use of a negative damping to eliminate the rotor damping. Numerical and experimental results show that the input-shaper can be effectively used for the vibration suppression of a slewing beam.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1854-1862
• /
• 2000

Input shaping method is to convolute input shaper, which is sequence of impulses, with reference input command not to excite the natural frequency of system. To reduce residual vibration for the ch ange of frequency, the number of impulses should be increased. Until now, amplitudes and time interval of those has been searched from the derivative of residual vibration. However, if time interval of impulses is fixed as the half of vibration period of system, input shaper H(z) in z-domain becomes (I-pz-1)n/K in which increasing n is the mean that robustness for change of parameter is improved. Also, design of many types of input shapers in z-domain is very easy because sensitivity curve is displayed with $\mid$H(z)zn$\mid$$\times$100. In the z-domain, EI(Extra-Insensitive) input shaper could be designed without solving nonlinear simultaneous equations as design in continuous time domain. In addition to, the design possibility of input shaper for a damped system was shown.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.83-89
• /
• 2008

This paper presents the dynamic analysis and input shaping control of a positioning stage. Vibration characteristics of the positioning stage are affected not only by the structural dynamics but also by the servo actuators that consist of the mechanism; driving motor and controller. This paper proposes an integrated dynamic model to accommodate both the structural dynamics and the servo actuators. Theoretical modal analysis with a commercial finite element code is carried out to investigate the dynamic characteristics of the experimental positioning stage. Experiments are performed to validate the theoretical modal analysis and estimate the equivalent stiffness due to the servo actuators. This paper deals with an input shaping scheme to suppress vibration of the positioning stage. Input shapers are systematically implemented for the positioning stage in consideration of its dynamics. The effects of servo control gain are also investigated. The experiments show that input shaping effectively removes residual vibrations and then improves the performance of positioning stage.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.542-549
• /
• 2012

This research is concerned with the derivation of equations of motion for a slewing beam and the application of input shaper to the bang-bang control to achieve vibration suppression. When a uniform beam with a tip mass rotates about the axis perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates. In this paper, we used the input shaper for the maneuvering control to suppress vibrations. The maneuvering control which can achieve a minimum-time control is a bang-bang control. The input-shaped bang-bang maneuvering is used to suppress vibrations both theoretically and experimentally. The slewing beam experiment is not an easy subject because of the inherent damping existing inside the rotor. We propose the use of a negative damping to eliminate the rotor damping. Numerical and experimental results show that the input-shaper can be effectively used for the vibration suppression of a slewing beam.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.62-67
• /
• 2003

This paper is concerned with the design of the beam forming module that is a key unit of the active phased array antenna(APAA) system for mobile satellite communications. This module includes two blocks for main signal and tracking signal. Main signal block has the role of transmitting input signal from phased array antenna to tracking signal block. And, tracking signal block executes main roles, beam forming of tracking signal and electronic beam control. The several electrical performances of this module, phase characteristics and linear gain, etc., agreed with specifications needed fur APAA, and for more clear verification of the performances, the satellite communication test of the APAA including the modules was accomplished in the outdoors.