• Korean Journal of Remote Sensing
• /
• 제31권5호
• /
• pp.441-448
• /
• 2015

Lack of agricultural information for food supply and demand in Democratic People's republic Korea(DPRK) make people sometimes confused for right and timely decision for policy support. We carried out a study to estimate paddy rice yield in DPRK using MODIS NDVI reflecting rice growth and climate data. Mean of MODIS $NDVI_{max}$ in paddy rice over the country acquired and processed from 2002 to 2014 and accumulated rainfall collected from 27 weather stations in September from 2002 to 2014 were used to estimated paddy rice yield in DPRK. Coefficient of determination of the multiple regression model was 0.44 and Root Mean Square Error(RMSE) was 0.27 ton/ha. Two-way analysis of variance resulted in 3.0983 of F ratio and 0.1008 of p value. Estimated milled rice yield showed the lowest value as 2.71 ton/ha in 2007, which was consistent with RDA rice yield statistics and the highest value as 3.54 ton/ha in 2006, which was not consistent with the statistics. Scatter plot of estimated rice yield and the rice yield statistics implied that estimated rice yield was higher when the rice yield statistics was less than 3.3 ton/ha and lower when the rice yield statistics was greater than 3.3 ton/ha. Limitation of rice yield model was due to lower quality of climate and statistics data, possible cloud contamination of time-series NDVI data, and crop mask for rice paddy, and coarse spatial resolution of MODIS satellite data. Selection of representative areas for paddy rice consisting of homogeneous pixels and utilization of satellite-based weather information can improve the input parameters for rice yield model in DPRK in the future.

• Journal of the Korean Vacuum Society
• /
• 제17권3호
• /
• pp.195-198
• /
• 2008

In this paper, it was demonstrated that organic thin-film transistors (OTFTs) were fabricated with the organic passivation layer by vapor deposition polymerization (VDP) processing. In order to form polymeric film as a passivation layer, VDP process was also introduced instead of spin-coating process, where polymeric film was co-deposited by high-vacuum thermal evaporation from 6FDA and ODA followed by curing. In order to investigate by compared with different passivation layer, the other OTFTs is fabricated to passivation by Polyvinylalcohol using spincoating. We can see that two different ways of passivation layer affect electric characteristic of OTFTs. The initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.24cm^2/Vs$, -3V, and $10^6$, respectively. Then after polyimide passivation layer, field effect mobility change from $0.24cm^2/Vs$ to $0.26cm^2/Vs$, threshold voltage from -3V to 1V and on-off current ratio from $10^6$ to $10^6$, respectively. In the case of polyvinylalcohol passivation, the initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.13cm^2/Vs$, 0V, and $10^6$, respectively. Then after polyvinylalcohol passivation layer, field effect mobility changes from $0.13cm^2/Vs$ to $0.13cm^2/Vs$, threshold voltage from 0V to 2V, and on-off current ratio from $10^6$ to $10^5$, respectively.

• Journal of Biosystems Engineering
• /
• 제8권1호
• /
• pp.47-60
• /
• 1983

상온통풍(常溫通風)을 이용(利用)한 In-bin drying에 대(對)한 많은 실험결과(實驗結果)에 의(依)하면 우리나라 10월(月)의 기상조건(氣象條件)은 저온건조(低溫乾燥) system에 적합(適合)한 건조능력(乾燥能力)을 가지고 있는 것으로 나타났다. 최근(最近) Computer를 이용(利用)한 Simulation model이 개발(開發)되어 건조현상(乾操現象)에 관(關)한 경제적(經濟的)이고 효율적(效率的)인 분석(分析)이 가능(可能)하게 되었다. 이러한 분석결과(分析結果)에 의(依)하면 초기함수율(初期含水率)이 높은 벼를 Full-bin을 이용(利用)한 상온통풍건조(常溫通風乾操)를 할 경우(境遇) 건조기간(乾燥期間)이 길어지며 bin내(內)의 상층부(上層部) 곡물(穀物)이 변질(變質)되는 문제점(問題點)이 발생(發生)하였다. 또한 벼의 수확작업체계(收穫作業體系)가 관행(慣行) 및 Binder작업체계(作業體系)에서 점차(漸次) Combine작업체계(作業體系)로 전환(轉換)되어감에 따라 포장(圃場)에서의 건조(乾燥)가 어려우며 예취(刈取), 탈곡작업과정(脫穀作業過程)에서의 기계적(機械的)인 곡물(穀物) 손실(損失)을 줄이기 위(爲)하여 함수율(含水率)이 비교적(比較的) 높은 벼를 수확(收穫)하여야 한다. 본(本) 연구(硏究)의 목적(目的)은 상온통풍건조(常溫通風乾燥)에 있어서 건조능력(乾燥能力)을 증가(增加)시키기 위(爲)하여 곡물(穀物)을 일정기간(一定期間) 나누어서 bin에 넣고 건조(乾燥)를 하는 Layer drying의 Simulation model을 개발(開發)하고 이 Model에 수원지방(水原地方)의 7년간(年間) 평균(平均) 기상자료(氣象資料)를 입력(入力)시켜 곡물(穀物)의 초기함수율(初期含水率), 투입량(投入量), 투입기간(投入期間)의 변화(變化)에 따른 Layer drying현상(現象)을 규명(糾明)하는데 있다. Simulation에 사용(使用)된 bin의 크기는 직경(直徑) 2m, 깊이 1.5m이며 송풍(送風)팬의 용량(容量)은 0.5HP이었다. Simulation분석(分析) 결과(結果)를 요약(要約)하면 다음과 같다. (1) Layer drying의 Simulation model을 개발(開發)하였으며 이 Model은 벼의 상온통풍건조(常溫通風乾燥) 실험(實驗)에서 함수량(含水量) 변화(變化)의 이론치(理論値)와 실제실험치(實際實驗値)가 잘 일치(一致)하였다. (2) 곡물투입기간(穀物投入期間) 1일(日)을 Full-bin drying으로 간주(看做)할 때 Layer drying의 건조성능(乾燥性能)은 Full-bin보다 높은 것으로 나타났다. (3) 연속송풍(連續送風)(24시간(時間))을 할 경우(境遇) 곡물투입기간(穀物投入期間)이 증가(增加)함에 따라 건조기간(乾燥期間)의 감소경향(減少傾向)은 단속송풍(斷續送風)인 경우(境遇)보다 적었지만 건조기간(乾燥期間)은 단축(短縮)되었다. 그러나 건조(乾燥)에너지의 소모(消耗)는 단속송풍(斷續送風)일 때보다 크게 나타났다. (4) 단속송풍(斷續送風)(9 : 00AM~6 : 00PM)일 경우(境遇) 곡물투입기간(穀物投入期間)을 증가(增加)시키면 건조기간(乾燥期間)이 크게 줄어 들었다. (5) 곡물(穀物)의 초기함수율(初期含水率)이 21% 이하(以下)일 경우(境遇) 연속(連續) 및 단속송풍(斷續送風)에서 건조기간(乾燥期間)의 차이(差異)가 별로 없었다. (6) 곡물(穀物)의 초기함수율(初期含水率)이 높으면 Full-bin drying에서는 상부층(上部層)에 곡물(穀物)이 변질(變質)될 우려(憂慮)가 있으나 Layer drying에서는 곡물투입량(穀物投入量)을 조절(調節)하면 이것을 방지(防止)할 수 있었다. (7) 건조(乾燥)가 완료(完了)된 후(後) 층별(層別) 최종곡물(最終穀物) 함수율(含水率)은 모든 건조조건(乾燥條件)에서 동일(同一)하였으나 bin의 하부층(下部層)은 과건조(過乾燥) 물상(物象)을 일으켰다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• 제39권4호
• /
• pp.347-357
• /
• 2003

This paper describes on the suppression of sea clutter on marine radar display using a cell-averaging CFAR(constant false alarm rate) technique, and on the analysis of radar echo signal data in relation to the estimation of ARPA functions and the detection of the shadow effect in clutter returns. The echo signal was measured using a X -band radar, that is located on the Pukyong National University, with a horizontal beamwidth of $$3.9^{\circ}$$, a vertical beamwidth of $20^{\circ}$, pulsewidth of $0.8 {\mu}s$ and a transmitted peak power of 4 ㎾ The suppression performance of sea clutter was investigated for the probability of false alarm between $l0-^0.25;and; 10^-1.0$. Also the performance of cell averaging CFAR was compared with that of ideal fixed threshold. The motion vectors and trajectory of ships was extracted and the shadow effect in clutter returns was analyzed. The results obtained are summarized as follows；1. The ARPA plotting results and motion vectors for acquired targets extracted by analyzing the echo signal data were displayed on the PC based radar system and the continuous trajectory of ships was tracked in real time. 2. To suppress the sea clutter under noisy environment, a cell averaging CFAR processor having total CFAR window of 47 samples(20+20 reference cells, 3+3 guard cells and the cell under test) was designed. On a particular data set acquired at Suyong Man, Busan, Korea, when the probability of false alarm applied to the designed cell averaging CFAR processor was 10$^{-0}$.75/ the suppression performance of radar clutter was significantly improved. The results obtained suggest that the designed cell averaging CFAR processor was very effective in uniform clutter environments. 3. It is concluded that the cell averaging CF AR may be able to give a considerable improvement in suppression performance of uniform sea clutter compared to the ideal fixed threshold. 4. The effective height of target, that was estimated by analyzing the shadow effect in clutter returns for a number of range bins behind the target as seen from the radar antenna, was approximately 1.2 m and the information for this height can be used to extract the shape parameter of tracked target..

• Journal of Biomedical Engineering Research
• /
• 제23권1호
• /
• pp.49-60
• /
• 2002

Receive dynamic focusing with an array transducer can provide near optimum resolution only in the vicinity of transmit focal depth. A customary method to increase the depth of field is to combine several beams with different focal depths, with an accompanying decrease in the frame rate. In this Paper. we Present a simultaneous multiple transmit focusing method in which chirp signals focused at different depths are transmitted at the same time. These chirp signals are mutually orthogonal in a sense that the autocorrelation function of each signal has a narrow mainlobe width and low sidelobe levels. and the crossorelation function of any Pair of the signals has values smaller than the sidelobe levels of each autocorrelation function. This means that each chirp signal can be separated from the combined received signals and compressed into a short pulse. which is then individually focused on a separate receive beamformer. Next. the individually focused beams are combined to form a frame of image. Theoretically, any two chirp signals defined over two nonoverlapped frequency bands are mutually orthogonal In the present work. however, a tractional overlap of adjacent frequency bands is permitted to design more chirp signals within a given transducer bandwidth. The elevation of the rosscorrelation values due to the frequency overlap could be reduced by alternating the direction of frequency sweep of the adjacent chirp signals We also observe that the Proposed method provides better images when the low frequency chirp is focused at a near Point and the high frequency chirp at a far point along the depth. better lateral resolution is obtained at the far field with reasonable SNR due to the SNR gain in Pulse compression Imaging .

• Journal of Korean Society of Environmental Engineers
• /
• 제28권10호
• /
• pp.1031-1037
• /
• 2006

The main purposes of this study were to compare the characteristics of fractionated natural organic matters(NOM) from Han River water and Wangsuk(W) stream water, and to investigate the relationships between NOM and the formation of disinfection by products(DBPs). Three types of resin such as XAD-4, XAD-7HP and IRC-50 were used to isolate the water samples into three organic fractions. The DOC concentrations of raw waters were relatively low($1.5{\sim}3.3$ mg/L) at all seasons. The hydrophilic was the major constituent, contributing $44{\sim}63%$ of the total NOM and hydrophobic $21{\sim}33%$, transphilic $16{\sim}31%$, respectively. The formation of trihalomethans(THMs) was highly influenced by particulated NOM especially in the rainy season, whereas haloaceticacid forming potentials(HAAFPs) depended more on the hydrophilic fraction of dissolved NOM which is known to be difficult to be removed through conventional processes. The NOM of W stream was characterized as 15% hydrophobic, 9% transphilic, and 76% hydrophilic. In the fractionation of NOM using resins, $20{\sim}40%$ of the NOM in W tributary water could not be clearly isolated, whereas, 85% of the NOM in the raw water was recovered. Although the DOC concentration of tributary water was higher than the raw waters from the Han River, the DBPFPs was approximately 40% of the raw waters. In DBPFPs aspect, W stream has less effect than Han River water itself. Bromide in tributary waters discharged from waste water treatment plants has been found to shift the distribution of THMs and HANs to the more brominated DBPs.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제32권2호
• /
• pp.295-301
• /
• 2003

This study was carried out to investigate perception about body image, dietary attitude, nutrient intake and dietary self-efficacy of high school students in Pusan. A questionaire survey was distributed among 491 high school students. The survey was conducted from April 8 to April 22 in 2002. The results are summarized as follows. Forty percents of the underweight group, 53.9% of the normal weight group, 61.8% of the overweight group and 48.2% of obesity group have correct perception about their body image. Most of the students were concerned with their body image and weight control. Obesity of parents was significantly correlated with obesity of the subjects (p<0.01). The higher obesity rate, the lower dietary self-efficacy. The higher dietary self-efficacy, the higher dietary attitude. There was a significant positive correlation between the education level of their parents and dietary attitude of the subjects (p<0.01) and a significant negative correlation between obesity rate of their mothers and dietary attitude of the subjects (p<0.01). Dietary attitude scores showed no significant difference among the groups. Intakes of most nutrients, except protein, niacin and vitamin C, were lower than those of the recommended dietary allowances for Koreans. Therefore, proper nutrition education is required to improve their nutritional status and dietary self-efficacy.

• Journal of the Korea Concrete Institute
• /
• 제14권4호
• /
• pp.457-466
• /
• 2002

An artificial neural network was applied to predict compressive strength, slump value and mix proportion of a concrete. Standard mixed tables were trained and estimated, and the results were compared with those of the experiments. To consider variabilities of material properties, the standard mixed fables from two companies of Ready Mixed Concrete were used. And they were trained with the neural network. In this paper, standard back propagation network was used. The mix proportion factors such as water cement ratio, sand aggregate ratio, unit water, unit cement, unit weight of sand, unit weight of crushed sand, unit coarse aggregate and air entraining admixture were used. For the arrangement on the approval of prediction of mix proportion factor, the standard compressive strength of $180kgf/cm^2{\sim}300kgf/cm^2$, and target slump value of 8 cm, 15 cm were used. For the arrangement on the approval of prediction of compressive strength and slump value, the standard compressive strength of $210kgf/cm^2{\sim}240kgf/cm^2$, and target slump value of 12 cm and 15 cm wore used because these ranges are most frequently used. In results, in the prediction of mix proportion factor, for all of the water cement ratio, sand aggregate ratio, unit water, unit cement, unit weight of sand, unit weight of crushed sand, unit coarse aggregate, air entraining admixture, the predicted values and the values of standard mixed tables were almost the same within the target error of 0.10 and 0.05, regardless of two companies. And in the prediction of compressive strength and slump value, the predicted values were converged well to the values of standard mixed fables within the target error of 0.10, 0.05, 0.001. Finally artificial neural network is successfully applied to the prediction of concrete mixture and compressive strength.

• Journal of the Korea Concrete Institute
• /
• 제23권6호
• /
• pp.711-722
• /
• 2011

Beam-column gravity or Intermediate Moment frames subjected to unexpected large displacements are vulnerable when no seismic details are provided, which is typical. Conversely, economic efficiency of those frames is decreased if unnecessary special detailing is applied as the beam and column size becomes quite large and steel congestion is caused by joint transverse reinforcement in beam-column connections. Moderate seismic design is used in Korea for beam-column connections of buildings with structural walls, which are to be destroyed when the unexpected large earthquake occurs. Nonetheless, performance of such beamcolumn connections may be substantially improved by the addition of steel fibers. This study was conducted to investigate the effect of steel fibers in reinforced concrete exterior beam-column connections and possibility for the replacement of some joint transverse reinforcement. Ten half-scale beam-column connections with non-seismic details were tested under cyclic loads with two cycles at each drift up to 19 cycles. Main test parameters used were the volume ratio of steel fibers (0%, 1%, 1.5%) and joint transverse reinforcement amount. The test results show that maximum capacity, energy dissipation capacity, shear strength and bond condition are improved with the application of steel fibers to substitute transverse reinforcement of beam-column connections. Furthermore, several shear strength equations for exterior connections were examined, including the proposed equation for steel fiber-reinforced concrete exterior connections with non-seismic details.

• Journal of the Korea Concrete Institute
• /
• 제24권3호
• /
• pp.275-283
• /
• 2012

Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.