• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.717-723
• /
• 2010

Many researchers have studied woven fabric carbon-fiber-reinforced composite (CFRP) materials but the study of fatigue crack propagation in composites has been insufficient. It has known that the crack propagation behavior differs depending on the load and the fiber direction. In this study, the fatigue crack propagation along two different fiber array directions ($0^{\circ}$, $45^{\circ}$) in plain woven CFRP composite was investigated. Fatigue crack propagation tests were conducted on the woven CFRP composite under a sinusoidal waveform load with stress ratios of 0.1 at a frequency of 10 Hz. Once the results of the tests were obtained, fatigue crack propagation rates (da/dN) were plotted against the energy release rate amplitude (${\Delta}G$), and it was observed that either mode I crack propagation or mixed mode crack propagation occurs depending on the fiber array direction.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.240-245
• /
• 2001

The tensile strength and failure mechanisms of glass fiber polypropylene (GF/PP) composites are investigated in the temperature range from ambient to 8$0^{\circ}C$. The tensile strength increases as fiber volume fraction ratio increase. The tensile strength shows a maximum at ambient temperature, and it tens to decrease as temperature goes up. Major failure mechanisms of GF/PP composites can be classified as fiber matrix debonding, fiber pull-out, delamination and matrix deformation.

• Applied Chemistry for Engineering
• /
• v.5 no.4
• /
• pp.737-742
• /
• 1994

The fracture energy of glass fiber/carbon fiber/epoxy resin hybrid composite system was investigated in the aspect of fracture mechanism. Epoxy resin matrix was DGEBA-MDA-SN-HQ system. On the interface of glass fiber and matrix, post debone friction energy provided a major contribution to the fracture energy, and debonding energy and pull-out energy were of the similar value. In the case of fracture on the interface of carbon fiber and matrix, pull-out energy was the major contributor.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.265-270
• /
• 2000

Injection molding is a very important industrial process for the manufacturing of plastics objects. During an injection molding process of composites, the fiber-matrix separation and fiber orientation are caused by the flow of molten polymer/fiber mixture. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation· orientation and injection molding conditions. So far, there is no research on the measurement of fiber orientation using image processing. In this study, the effects of fiber content ratio and molding condition on the fiber orientation-angle distributions are studied experimentally. Using the image processing method, the fiber orientation distribution of weld-line parts in injection-molded products is assessed. And the effects of fiber content and injection molding conditions on the fiber orientation functions are also discussed

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.337-343
• /
• 2004

This paper presents an experimental study of friction and wear properties of a unidirectional oriented continuous crbon-fiber reinforced epoxy composite at the ambient temperature. Friction and wear experiments were conducted in the three principal sliding direction of the fiber orientation in the composite were selected against the stainless steel counterpart specularly processed were using a pin -on-disc apparatus. Friction coefficient and specific wear rate at various normal loads and sliding velocities wear determined. When sliding took place against smooth and hard counterpart, the hightest were resistance and the lowest friction coefficient were observed in the anti-parallel direction. The wear track of the worn specimens was examined with a scanning electron microscope(SEM) to observe the damaged fibers on the surface. In addition, SEM observations of the worn surfaces allowed to identify the involved different wear mechanisms.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.2
• /
• pp.149-158
• /
• 2011

Utilization of the fiber reinforced polymer (FRP) material has been increased as an alternative in a bid to supplement the problems with general construction materials such as long-term problems corrosion, etc. However, there are still many problems in using a linear-shaped FRP material for a tunnel lining structure which has arch-shape in general. In this study, the loading tests for the FRP-concrete composite member was carried out to evaluate their applicability as a tunnel reinforcement material, which are based on the results from preliminary numerical studies for identifying the behavioral characteristics of FRP-concrete composite member. Moreover, numerical analysis under the same condition as applied in the loading tests was again conducted for analysis of mechanical behavior of the composite member. As a result of the load test and numerical analysis, it appears that the FRP-concrete composite member is greatly subject to shear movement caused by bending tension acting on the interface between two constituent members.

• Journal of Adhesion and Interface
• /
• v.23 no.3
• /
• pp.59-69
• /
• 2022

In composite materials, the adhesion and interfacial properties were the most important factors to obtain high performance of mechanical properties. This review paper had been focused on the micromechanical evaluation methods for the interfacial property historically. The interfacial property of fiber-reinforced composites (FRC) could be evaluated using only a single fiber and matrix via various micromechanical testing methods. Self-sensing due to the fracture behavior of FRC could be determined and discussed more critically and clearly using electro-micromechanical evaluation. In this paper, the research trends for micro-mechanical evaluation of composites was summarized, and their practical applications would be suggested in the future.

• Composites Research
• /
• v.22 no.4
• /
• pp.13-19
• /
• 2009

Adhesive joints are widely used for structural joining applications in various fields and environmental conditions. Polyurethane adhesive is using for LNG carrier with cryogenic temperature condition. Even if similar polyurethane adhesive is used for different substrate, it shows different adhesion properties. Specially, variation of adhesion properties depending on the resin system or fiber is very important factor for selection of adhesive on industrial application. In present study, we got different peel strength according to the different test temperature when different polyurethane adhesive was used for same fiber reinforced composite. The main cause was investigated using by SEM and it was proven that the different adhesion property between glass fiber on composite surface and polyurethane adhesives at cryogenic temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.3
• /
• pp.52-62
• /
• 1994

기계나 구조물 파괴의 대부분은 노치부를 기점으로 하여 발생하기 때문에 첨단복합재료를 노지부 재로서 안전하면서도 경제적으로 사용하기 위해서는 각종 조건하에 있어서 강도특성을 명확히 하는 것은 대단히 중요하다. 본 연구에서는 노치를 갖는 복합재료를 이용하여 각종조건하에서 강도특성평가실험을 행하였으 며, 얻어진 결과를 종합하면 다음과 같다. (1) 첨단복합재료 노치재는 試驗片의 幾可學的 形狀과는 관계없이 노치반경 p만에 의해 결정되는 최대탄성응력 $\sigma_{max}$일정의 條件下에서 破t짧된다. (2) 破斷時 최소단면에서의 공칭응력 $\sigma_{c}$와 응력집중계수 $K_{t}$와의 관계에 있어서,$\sigma_{c}$의 값이 $K_{t}$의 증대와 더불어 떨어지고 있는 부분과, $K_{t}$와 관계없이 거의 일정하게 되고 있는 부분으로 나누어지는 現象은 노치재의 回轉굽힘 또는 인장압축파열에서 보여지는 현상과 外觀上 對應하고 있다. 즉, 정적파괴와 피로파괴는 파괴의 양상이 비슷하다 (3) PEN수지단체의 경우, 피로균열발생은 점발생적 피로균열이 최대탄성응력에 의해 지배되며, 노치에 만감하며,균열전파수명은전수명에 비해 상당히 짧다. (4) 단탄소섬유강화복합재료의 경우, 피로균열은 섬유端에 응력이 집중하기 때문에 일반적으로 섬유端에서 아주 빠른 시기에 발생하지만, 섬유가 피로균열진전에 대해 방해물로 작용하기때문에 아주 천천히 전파한다. (5) 短탄소鐵維는 피로균열발생에 대해서는 負의 강화작용 전수명의 극히 초기단계에 피로균열 발생을, 피로균열전파에 대해서는 正의 강화작용을 한다. (6) 단탄소섬유를 PEN에 강화함으로 인해 정적강도 보다 피로강도에 더 큰 강화효과를 초래했으며, 선형노치역학의 개녀은 첨단 복합재료의 강도평가에 대단히 유효했다.

• Composites Research
• /
• v.16 no.2
• /
• pp.18-25
• /
• 2003

The tensile properties of short nylon6 fiber reinforced NR and SBR have been investigated as functions of fiber aspect ratio(AR), diameter ratio(DR), interphase condition, and fiber content. The tensile strength increased with increasing fiber AR(20 min.) and good interphase conditions. The short-fiber(DR=3 and AR=20 min.) reinforced SBR did not show the dilution effect for all interrhase conditions. And the short-fiber(DR=3 and AR=20min.) reinforced NR did not show the dilution effect except for the no-coating. The tensile moduli were significantly improved due to fiber AR. fiber content, and good interphase at same DR. The better interphase condition showed the higher pull-out force at same DR. Also, the stress analysis near the fiber end carried out using axisymmetric FEA to be convinced of the reinforcing mechanism. It is found that the fiber AR, interphase and DR have an important effect on tensile properties.