• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.6
• /
• pp.471-478
• /
• 2018

Static tests of the composite wing structure were performed to verify damage tolerance design. Both 5 cases of DLLT and 3 cases of DULT were completed to meet requirements for static strength. After inducing BVID and open hole damages on the critical areas of the composite wing based on associated regulations, the DULT and fracture test were performed. In major wing parts, the measured strains and displacements agreed well with those of structural analysis. The initial structural fracture occurred at the area having minimum margin of safety as expected by analysis. As a result, it was confirmed that results from analytic model and strength evaluation were similar to behaviors of the composite wing structure.

• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 1993.07a
• /
• pp.45-50
• /
• 1993

항만과 방파제와 같은 해양시설물은 해양의 자연환경에서 사용하는 구조물이므로 당연히 설치해역의 평상시의 자연환경 하중을 받으면서 기능유지가 가능하여야 하며, 또한 극한 자연환경 하중에도 견딜 것이 요구된다. 해양시설물 설계시에 고려해야할 자연환경조건으로는 바람, 파랑, 조류, 해류, 지진, 해저지반 등이다. (중략)

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.28.1-28.1
• /
• 2009

고해상도 카메라 혹은 영상레이더 안테나를 장착하여 지구를 관측하는 인공위성의 구조체는 발사하중 및 우주환경의 궤도 상에서 탑재된 장비를 보호하게끔 설계되고 제작된다. 구조체는 발사체와의 공진을 피할 수 있는 강성을 가져야 하며, 주 구조물의 강도는 발사체로부터의 하중을 견딜 수 있도록 설계된다. 또한, 극한 우주환경 하에서 구조체의 변형이 최소화 되도록 설계된다. 상기 설계 내용이 완벽하게 구조체에 반영되기 위해서는 우주용자재 및 공정의 적절한 선정이 이루어 져야 한다. 이 논문은 인공위성 구조체에 사용된 Metal, Non-metal 및 조립용 Hardware 자재 (규격 포함)와 측면패널/플랫폼 및 태양전지판 Substrate 등 주요 구조물의 제작공정에 대하여 기술한다. 그리고, 국산화가 이루어진 조립용 Hardware의 Dry Film Lubricant 공정에 대해서도 기술한다.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.267-278
• /
• 2016

In this study, the ultimate strength of 335 simply supported reinforced concrete beams with shear span-to-effective depth ratio of less than 3 was evaluated by the ACI 318-14's strut-tie model approach implemented with the indeterminate strut-tie models and load distribution ratios of the companion paper. The ultimate strength of the beams was also estimated by using the experimental shear strength models, the theoretical shear strength models, and the current strut-tie model design codes. The validity of the proposed strut-tie models and load distribution ratios was examined by comparing the strength analysis results classified according to the prime design variables of the shear span-to-effective depth ratio, flexural reinforcement ratio, and compressive strength of concrete.

• Journal of Wind Energy
• /
• v.5 no.1
• /
• pp.22-32
• /
• 2014

The structural design of a wind turbine must show the verification of the structural integrity of all load-carrying components. Also, design load calculations shall be performed using appropriate and accurate methods. In this study, advanced numerical approach for the calculation of design loads based on unsteady computational fluid dynamics (CFD) is presented considering extreme design load conditions such as the extreme coherent gust (ECG) and the 50 year extreme operating gust (EOG). Unsteady aerodynamic loads are calculated based on Reynolds average Navier-Stokes (RANS) equations with shear-stress transport k-ω(SST k-ω) turbulent model. A full three-dimensional 5 MW offshore wind-turbine model with rotating blades, hub, nacelle, and tower configuration is practically considered and its aerodynamic interference effect among blades, nacelle, and tower is also accurately considered herein. Calculated blade loads based on unsteady CFD method with respect to blade azimuth angle are compared with those by NREL FAST code and physically investigated in detail.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.8
• /
• pp.47-59
• /
• 2016

Rocking behavior of shallow foundation reduces the superstructure load during earthquake. However, because of deficiency of understanding of rocking mechanism and soil permanent deformation, it has not been applied to real construction. In this study, slow cyclic tests were conducted for embedded shallow foundations with various slenderness ratio via centrifuge tests. From the variation of earth pressure 'soil rounding surface' phenomenon which makes maximum overturning moment equal to ultimate moment capacity was observed. Rocking and sliding behavior mechanism was evaluated. Also, nonlinear behavior and energy dissipation increase as rotation angle increases. And ultimate moment capacity of embedded foundation is larger than that of surface foundation. Finally, adequate ultimate moment capacity can be suggested for seismic design through this study.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.84.1-84.1
• /
• 2010

국내에서는 플레이트거더의 휨 강도 및 전단 강도를 허용응력설계법에 기반한 도로교설계기준(2005)에 근거하여 규정하고 있으며, 국외의 경우 하중저항계수설계법에 근간을 둔 AISC(2005) 등의 규정을 통해 산정하고 있다. 최근에는 인장강도 800MPa 급의 강재가 생산되고 있으나 국내 설계기준에서는 아직까지 상기 인장강도를 갖는 고강도강에 대한 설계기준은 마련되지 않고 있다. 본 연구에서는 휨과 전단이 동시에 작용하는 고강도강 적용 플레이트거더의 극한거동 해석을 통해 국내기준의 적용성을 판단하고, 국외기준인 AISC(2005)와 비교하여 나타내어 허용응력설계법에 근거한 국내기준의 강도산정법의 한계점에 대해 고찰하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.182.2-182.2
• /
• 2010

설계단계의 풍력발전시스템 하중계산은 20년이 넘는 시스템 수명과 효율을 결정하는 중요한 부분이다. 일반적인 규정서 기반의 설계하중 계산은 실제 풍황 조건인 발전기 상호 간섭, 설치 지형의 특성 등을 상세히 묘사하기 어렵다. 풍력발전기 설계 단계에서 검토된 평균풍속 또는 난류강도 등이 규정(IEC, GL 등)을 만족한다 하더라도 설계값과 실제값은 서로 다른 결과를 나타낼 수 있다. 본 연구에서는 기 설계된 풍력발전기가 최적 효율을 낼 수 있는 풍력단지의 풍황 특성(평균풍속과 난류강도 등)의 범위를 보다 정확하게 제시하여 설치되는 풍력발전기의 수명과 효율을 높이는 방법을 연구하였다. 이를 위하여 당사의 2MW급 IEC Class II-A로 설계된 직접 구동형 풍력발전기에 대해, 다양한 평균 풍속(7m/s~10m/s)과 난류강도(14%~20%)를 고려한 하중 계산을 수행하였다. 하중 분석을 통해 실제 풍황 조건에 따른 극한하중 산출 및 피로수명의 민감도를 검토하여 풍력발전기 운용의 풍속과 난류강도의 최적범위 제시하여 발전단지 설계에 활용할 수 있도록 하였다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.2
• /
• pp.112-121
• /
• 2013

The calibration of resistance factor in reliability theory for limit state design of gravel compaction piles (GCP) requires a reliable estimate of ultimate bearing capacity. The static load test is commonly used in geotechnical engineering practice to predict the ultimate bearing capacity. Many graphical methods are specified in the design standard to define the ultimate bearing capacity based on the load-settlement curve. However, it has some disadvantages to ensure reliability to obtain an uniform ultimate load depend on engineering judgement. In this study, a well-fitting nonlinear regression model is proposed to estimate the ultimate bearing capacity, for which a nonlinear regression analysis is applied to estimate the ultimate bearing capacity of GCP and the results are compared with those calculated using previous graphical method. Affect the resistance factor of the estimate method were analyzed. To provide a database in the development of limit state design, the load test conditions for predicting the ultimate bearing capacity from static load test are examined.

• Computational Structural Engineering
• /
• v.2 no.2
• /
• pp.93-99
• /
• 1989

Since 1960's, structural engineers have recognized that the inherent random nature of loadings and materials as well as the imperfect structural analysis may be important factors in the structural safety evaluation. Based on the successful developments of the reliability-based structural analysis and design, the design criteria of the standards are recently developed(or modified) in the light of the probabilistic concepts. To develop the probability - based criteria for the domestic buildings, the probabilistic characteristic of loadings acting on structures should be defined first. In this study, therefore, live load data on apartment buildings have been collected and analyzed in systematic manner, and their probabilistic characteristics have been studied. Based on the results, the lifetime extreme values are computed and compared with current design loads. More rational design loads are suggested, which are more consistent in the probabilistic concepts.