• Journal of the Korean Geotechnical Society
• /
• v.15 no.1
• /
• pp.63-78
• /
• 1999

For the design of compression anchor, three things should be considered. The first is a resistance force by skin friction, the second is a tension strength of tendon, and the third is a compressive strength of grout. Especially, compressive strength of grout is the most important design parameter of compression anchor. When compression anchor is pulled out from the ground, the compressive strength of grout increases by confining pressure of ground($\sigma_{tg$). Here, $\sigma_{tg$ is the confining pressure which is produced by earth pressure at rest and by lateral expansion of grout. We call this phenomenon of increase of confining pressure "poisson effect". In this paper, the design method of compression anchor called SSC anchor and the computer program for the design are developed through compression tests of anchor body grout.ody grout.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.84-87
• /
• 2009

본 논문에서는 최근 초고층 건축물에 많이 활용되어지는 기둥-가새 시스템인 다이아그리드 시스템을 활용하여 중저층 건축물에 적용가능성을 평가하였다. 본 시스템은 튜브구조의 형태로 횡력에 대한 저항력이 우수하며 중력하중과 황하중을 기초와 지반에 안전하게 하중을 전달한다. 다이아그리드는 경사기둥과 보를 반복적으로 삼각형 형태로 배치되어 중력하중을 받을 경우 수직부재는 압축력을 보는 인장력을 받게 된다. 경사기둥과 보를 연결하는 접합부는 H-형강으로 설계 시 제작이 복잡하고 외관이 좋지 않다. 하지만 원형강관을 사용 할 경우 복합하지 않은 형태로 설계가 가능하고 외관이 우수하기 때문에 외부에 노출이 가능해진다. 또한 원형강관은 개방형 단면 부재에 비해 압축좌굴과 비틀림에 대한 성능 등이 우수하여 구조적인 성능이 우수하다. 원형강관을 이용하여 다이아그리드 시스템이 고층 건축물 뿐만 아니라 중저층 건축물에도 적용 타당성을 검토하였으며 원형강관 접합부 설계는 한계상태설계법이 사용 된 KBC2008(안)을 이용하여 설계하였다.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.8
• /
• pp.31-42
• /
• 2019

A total of 73 pile design data for prebored PHC piles was analyzed to study the current design method. Based on the design data, a ratio of skin friction to total capacity from the pile design data was about 20~53%. Such low ratio of skin friction to total capacity tends to underestimate skin friction. Considering this tendency, the current design method should be improved. Also, an average design efficiency of PHC pile capacity was 70% and an average design efficiency for bearing capacity of soil or weathered rock was 80%, which shows slightly higher value than the former. This is probably due to the fact that the allowable bearing capacity is estimated to be equal to or slightly higher than the design load. Hence, the allowable bearing capacity should be estimated to be higher than the long-term allowable compressive force of the PHC pile. In the current design method, skin friction is calculated to be about 2.2 times lower than end bearing. The current design method for prebored PHC piles applied foreign design methods without any verification of applicability to the domestic soil or rock condition. Therefore, the current design method for prebored PHC piles should be improved.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.36-36
• /
• 1999

일반적으로 이젝터(ejector)는 노즐로부터 팽창하는 높은 운동량을 가지는 주 유동과 주변의 낮은 운동량을 가지는 유동사이에서 생기는 강한 전단력을 이용하여, 분류 주변의 유체를 보다 고압의 부분까지 압축하여 수송하는 장치이다. 이젝터는 노즐(nozzle)과 디퓨저(diffuser)로 되어 있으며, 회전부분이나 활동부분을 가지지 않는 유체기계이므로 고장이 적고, 소형임에도 불구하고 대용량의 유체를 압축할 수 있는 특징을 가지고 있다. 그러나 이젝터의 구동은 유체의 전단력만을 이용하므로 효율이 낮은 단점이 있으므로, 이젝터 형상의 최적설계 및 성능개선을 위한 연구가 필요하다.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.52-57
• /
• 2002

본 논문은 고온 고압의 유체를 수송하는 해저 파이프의 좌굴 현상에 대해서 논하였다. 고온 고압의 유체를 해저 파이프로 수송 할 때, 수송되는 고온 고압의 유체와 수위 해저의 온도와 압력들의 차에 의해서 유체 수송 파이프는 축 방향으로 압축력을 받게 되고 이 압축력을 견디지 못하면 수송 파이프는 수직 방향의 좌굴 현상이 발생하게 된다. 논문에서는 "semi-empirical design method"를 사용하여 수송 유체의 온도와 압력의 여러 가지 변화에 따라 파이프의 축 방향 압축력을 계산하고 수직 좌굴 현상에 따른 안전계수를 구하여 파이프의 초기 설계 결정에 도움을 주고자 했다.

• Computational Structural Engineering
• /
• v.6 no.2
• /
• pp.13-16
• /
• 1993

본 고에서는 철골 구조물에 있어서 일어나고 있는 좌굴에 대해, 현재 외국에서 진행중인 연구의 일부를 소개하였다. 이들의 기본 개념은 좌굴이 일어날 수 있는 압축부재에 있어서 최대내력, 즉 좌굴이 일어나기 이전에 부재를 압축에 대해 항복시킴으로써, 좌굴을 방지하려는 연구의 일종으로서, 부재의 강도면에 있어서는 큰 손실이 뒤따르게 된다. 하지만, 트러스 등의 구조물에 있어서 압축보다 인장에 대해서 사전에 항복하도록 설계(선인장 항복설계)가 이루어진 경우일지라도, 인장항복만으로 붕괴기구가 형성된다. 또한, 일반적으로 트러스를 제작함에 있어서 시공상의 오차가 발생할 가능성이 상존하고 있으며, 부정확하게 시공된 구조물에 있어서는 설계시 상정된 파괴기구와는 다른 형태의 파괴기구가 형성될 가능성이 있다. 따라서, 안정항복하여 큰 소성변형이 필요한 경우에는 상기의 방법이 유효하다고 사료된다. 한편 본 고에서 예로 다루고 있는 2중 강관구조에 있어서는, 외관과 내관의 단면적비가 약 1:1.5 정도이며, 보강재로 사용되는 내관을 아무리 저급의 제품을 사용한다해도 불경제적이 될 가능성이 크다. 따라서 금후, 내관의 단면 결정을 위한 많은 연구가 이루어져야 한다고 생각한다.

• Journal of the Korea Concrete Institute
• /
• v.15 no.4
• /
• pp.594-605
• /
• 2003

Pinching is an important property of reinforced concrete member which characterizes its cyclic behavior. In the present study, numerical studies were performed to investigate the characteristics of pinching behavior and the energy dissipation capacity of flexure-dominated reinforced concrete members. By investigating existing experiments and numerical results, it was found that flexural pinching which has no relation with shear action appears in RC members subject to axial compression force. However, members with specific arrangement and amount of re-bars, have the same energy dissipation capacity regardless of the magnitude of the axial force applied even though the shape of the cyclic curve varies due to the effect of the axial force. This indicates that concrete as a brittle material does not significantly contribute to the energy dissipation capacity though its effect on the behavior increases as the axial force increases, and that energy dissipation occurs primarily by re-bars. Therefore, the energy dissipation capacity of flexure-dominated member can be calculated by the analysis on the cross-section subject to pure bending, regardless of the actual compressive force applied. Based on the findings, a practical method and the related design equations for estimating energy dissipation capacity and damping modification factor was developed, and their validity was verified by the comparisons with existing experiments. The proposed method can be conveniently used in design practice because it accurately estimates energy dissipation capacity with general design parameters.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.77-83
• /
• 2002

A computational study on the performance prediction of a two-stage axial compressor has been performed. A quasi-steady mixing-plane method is used on the rotor/stator interface to simulate the unsteady interaction phenomena. Detail flow mechanisms, for example, choke, stall, shock/boundary interaction, etc., have been observed and discussed in conjunction with performance characteristics. Calculational data agree reasonably well with the experimental data in terms of the performance characteristics showing the applicability of computational methods to the design validation of multistage axial compressors instead of experimental methods. But it is found that the stall margin of the original compressor was rather small, thus the design modification adopting a simple 1D/2D method has been conducted and its corresponding computations are also carried out. As a result of the redesign process, the stall margin becomes wide enough, but the overall performance is unsatisfactory, therefore, it seems that the redesign of the blades using 3-D methods is needed in the future work.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.9
• /
• pp.29-36
• /
• 2019

Axial compressive failure loads ($P_n$) of diameter 500 mm and diameter 600 mm A type PHC pile were calculated as 7.7 MN and 10.6 MN, respectively. In the static pile load tests, the maximum axial compressive loads of the above 2 kinds of A type pile were measured as 6.9 MN and 8.8 MN respectively, therefore these measured maximum loads were at the level of 90% and 83% of $P_n$ respectively. Long-term allowable axial compressive loads ($P_a$) of the above 2 kinds of A type pile were 1.7 MN and 2.3 MN respectively. From the bi-directional pile load test data on the prebored PHC piles, it was confirmed that the allowable axial compressive bearing resistance was estimated as 131% of the long-term allowable compressive load of the PHC pile and showed higher than the allowable bearing capacity calculated by the current design method. Therefore, it has been verified that the PHC pile can be used up to the maximum long-term allowable compressive load, and it is suggested that the ultimate pile capacity formula used in the current design for prebored PHC piles should be improved to accommodate the actual capacity.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.4 s.37
• /
• pp.677-689
• /
• 1998

In relation to concentrically loaded compression, this research is to describe, analyze, and evaluate the design strength in steel stud. The similarity and difference among load and resistance factor design specification for cold-formed steel structural members (AISI), cold-formed thin gauge members and sheeting (EC3 part 1.3), and German draft (DASt-Richtlinie 016) are introduced, discussed, and systematically evaluated. Especially, the effective width and global instability problems (flexural buckling and torsional flexural buckling) are here implied in this research. The design axial strength by dual standards (AISI and EC3) is calculated and compared using the example.