• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.3
• /
• pp.1-8
• /
• 2009

This thesis has analyzed the effect of the surge happening in flight on the engine performance, especially on the PW4000 turbofan engine. It is to be judged that the flight surge can occur more often at the time of takeoff than it does en route due to the fact that the engine parameters are prone to fluctuate. EPR is judged to be the most highly sensitive parameter responding when surge occurs. Both Engine rpm and Wf decrease almost simultaneously just like an EPR. During the take-off rolling, N1 vibration is more sensitive than the N2 vibration. Consequently, the surge can be detected by EGT increase, while the other parameters (EPR, rpm, Wf, etc) decrease.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.236-239
• /
• 2008

This thesis has analyzed the effect of the surge happening in flight on the engine performance of the PW4000 turbofan engine. EPR is judged to be the most highly sensitive parameter responding when surge occurs. Both N1 rpm and N2 rpm decreases almost simultaneously just like an EPR. During the take-off rolling, the N1 vibration is more sensitive than the N2 vibration. Consequently, the surge can be detected by EGT increase, while the other parameters decrease.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.731-736
• /
• 2007

Vibration isolation equipments are mostly required in precise measurement and manufacturing system. Among all the vibration isolation system, air-spring is the most widely used equipment because of low resonant frequency and high damping ratio. In this study, Takagi-Sugeno fuzzy method is used to design an active vibration isolation system using air-spring, and compared the fuzzy method with passive control method and PID control method. Due to the non-linearity characteristics of air-spring, fuzzy controller was verified to be the most effective both in simulation and experiment.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.68-77
• /
• 2017

High-frequency combustion instability results from a feedback coupling between the unsteady heat release rate and the acoustic waves formed resonantly in the combustion chamber. It can be modeled as thermoacoustic problems with various degrees of the assumptions and simplifications. This paper presents numerical analysis of self-excited combustion instabilities in a variable-length lean-premixed combustor and designs of passive control devices such as baffle and acoustic resonators in a framework of 3-D FEM Helmholtz solver. Nonlinear behaviors such as steep-fronted shock waves and a finite amplitude limit cycle are also investigated with a compressible flow simulation technique.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.180-195
• /
• 2000

Grouting has been practiced as a reliable technique to improve the mechanical properties of rock mass. But, the study of ground improvement by greeting is rare especially in jointed rock mass. In this study, joint compression test and direct shear test were performed on pure rock joint and cement milk grouted rock joint to examine the grouting effect on the property of rock joint. In the pure rock joint compression test, joint closure varied non-linearly with normal stress. But after cement milk grouting, the normal deformation characteristics of the joint was linear at the low normal stress level. As normal stress increased. deformation of the sample rapidly increased due to the stress concentration at the joint asperities. Peak shear strength of the grouted joint in low normal stress was higher than that of non-grouted joint due to the cohesion, decreased exponetially as the grout thickness increased. Thus after cement milk grouting, the failure envelope modified to a curve that has cohesion due to grout material hydration with decreased friction angle. Shear stiffness and peak dilation angle of the grouted joint decreased as the grout thickness increased. The peak shear strength from the direct shear test on grouted rock joint was represented by an empirical equation as a fuction of grout thickness and roughness mean amplitude.

• Journal of the Korea Concrete Institute
• /
• v.21 no.4
• /
• pp.401-408
• /
• 2009

A compression lap splice becomes an important issue due to development of ultra-high strength concrete. Current design codes regarding compression lap splice do not utilize merits of the improved strength of ultra-high strength concrete. Especially, a compression lap splice can be calculated longer than a tension lap splice according to the codes because they do not consider effects of compressive strength of concrete and transverse reinforcement. This anomaly confuses engineers in practice. Design equation is proposed for compression lap splice in 40 to 70 MPa of compressive strength of concrete. The proposed equation is based on 51 specimens conducted by authors. Basic form of the equation includes main parameters which are derived from investigating test results. Through two-variable non-linear regression analysis of measured splice strengths, a strength equation of compression lap splices is then derived. A specified splice strength is defined using a 5% fractile coefficient and a lap length equation is constructed. By the proposed equation, the anomaly of lap lengths in tension and compression is got rid of. In addition, the equation has a reliability equivalent to those of the specified strengths of materials.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1329-1334
• /
• 2004

The most compact and convenient pulse tube cryocooler for practical applications is the coaxial type. It can replace Stirling cryocooler without any change to the Dewar or the connection to the cooled devices. The experimental results of the coaxial inertance tube pulse tube cryocooler for cooling superconductor RF filter are presented in this paper. To find optimal conditions of inertance tube pulse tube cryocooler, no load temperature according to the variations of inertance tube volume, reservoir volume are measured, and the cool down characteristics at the particular conditions are presented. In case of the coaxial type inertance tube pulse tube refrigerator, cool down time is the lowest in the inertance tube diameter of 1.3 mm and inertance tube length of 1900 mm and lowest temperature is 112K. This results are not satisfactory for practical applications. So, We propose vacuum insulation between regenerator and pulse tube in the Stirling type coaxial pulse tube cryocooler. Stirling type coaxial pulse tube cryocooler with the vacuum insulation between regenerator and pulse tube was designed and manufactured by KIMM(Korea Institute of Machinery and Materials). The optimal conditions will be tested for Stirling type coaxial pulse tube cryocooler with the vacuum insulation between regenerator and pulse tube.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1701-1708
• /
• 2002

본 연구의 목적은 자외선 차단 가공 처리 및 자외선 조사처리에 의해 면직물의 역학적 특성 변화를 조사하고 가공제 처리조건에 따른 차이점을 분석하는 것이다. 시료로는 100% 면직물을, 자외선 흡수제로 2,2'-dihydroxy-4,4'-dimethoxy benzophenone을, 첨가제로 Triton X-100, polyethylene glycol 400, MgCl$_2$.6$H_2O$를 사용하였다. 자외선 흡수제 처리는 Atlas Launder-O-meter로 75$^{\circ}C$에서 60분간 흡진법으로 하였다. 미처리 시료 및 처리시료는 모두 xenon 램프에 80시간 동안 노출되었으며, 자외선 조사 전후 시료의 역학적 특성은 KES-F시스템을 사용하여 측정하였다. 본 연구의 결과는 다음과 같이 요약할 수 있다. 자외선 흡수제 처리는 처리 농도에 상관없이 면직물의 선형인장성(LT), 인장레질리언스(RT), 굽힘강성(B), 굽힘이력(2HB), 전단강성(G), 전단이력(2HG5), 표면마찰계수(MIU)등을 증가시켰으며 표면거칠기(SMD)는 감소시켰다. 압축특성은 처리농도의 영향을 받아서 고농도의 자외선 흡수제 처리는 압축특성을 감소시켰으며, 저농도의 처리는 압축특성을 증가시켰다. 자외 선 흡수제 처리는 처리농도에 상관없이 면직물의 fullness/softness를 유의하게 증가시키는 반면 stiffness, crispness및 anti-drape stiffness를 감소시켜서 가공포의 종합태(THV)는 가공 전에 비하여 저하하였다. 자외선 조사는 가공 전 면직물의 경우 B, 2HB, G, 2HG, 2HG5, LC를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의 WT, 굽힘특성 , 전단특성을 감소시켰으며, 저농도의 흡수제 처리포의 경우 SMD를 증가시켰으며, 고농도의 흡수제 처리포의 경우 SMD를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의fullness/softness, stiffness, anti-drape stiffness를 유의하게 감소시켜서 자외선 조사 전 보다 THV가 37% 저하하였고 미 가공포의 THV를 저하율보다는 저하가 낮았다. 자외선 흡수제 처리에 의해 면직물의 태는 가공 전보다 감소하지만, 자외선 흡수제 처리는 자외선 조사에 의한 태 감소율을 낮추는 데 유의 한 효과가 있다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.2
• /
• pp.61-67
• /
• 2012

In this paper, In this paper, we consider a dynamic range in the frequency converter to obtain a high conversion gain and linearity while operating area proposed to broaden the design. Super-heterodyne RF Front-End style was applied to the active mixer stage, GaAs devices were used. Circuit design easy and simple forms benefit circuit is constructed in the drain mixer, passive mixer with the operating area were compared and analyzed. The simulation results of the conversion gain of 2.4dB and 0.2dBm about a gain-compression point, and showed the dynamic range of 71.9dB, when compared with passive mixers, dynamic range of approximately 6dB improvement was identified. Measurements of an approximately 2dB conversion gain and-1.0dBm of the gain-compression point, and confirmed that the active area of 71.1dB. When compared with passive mixers, dynamic range of is reduced by approximately 8dB has been improved.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.424-429
• /
• 2003

A reciprocating compressor with a rotary motor used in a refrigerator has low efficiency, because it has the large mechanical losses due to the crank mechanism. The linear compressor which has the free piston driven by a linear motor, was developed to increase the efficiency of compressor by reducing mechanical losses. The TRIAC has been widely used for controlling the piston, because it has simple structure. However, as it is able to control only stator voltage, it is very difficult to obtain good efficiency. Recently, PWM inverter which is able to control the voltage as well as the frequency, is applied to linear compressor drive system to overcome above problem. In this paper, the variations for efficiency and power factor of linear compressor are investigated by changing both the mechanical resonant frequency and electrical resonant frequency of linear compressor, and also the inverter frequency The optimum relationships between both resonant frequencies and the inverter frequency is derived in order to obtain the maximum efficiency and also good power factor.