• Progress in Medical Physics
• /
• v.9 no.1
• /
• pp.11-21
• /
• 1998

Circular metal electrodes were vacuum-deposited with chromium on the both sides of Teflon-FEP and PET film characteristic of electret and the physical properties of the two polymers were observed during an irradiation by gamma-ray from $\^$60/Co. With the onset of irradiation of output 25.0 cGy/min the induced current increased rapidly for 2 sec, reached a maximum, and subsequently decreased. A steady-state induced current was reached about in 60 second. The dielectric constant and conductivity of Teflon-FEP were changed from 2.15 to 18.0 and from l${\times}$l0$\^$-17/ to 1.57${\times}$10$\^$-13/ $\Omega$-$\^$-1/cm$\^$-1/, respectively. For PET the dielectric constant was changed from 3 to 18.3 and the conductivity from 10$\^$-17/ to 1.65${\times}$10$\^$-13/ $\Omega$-$\^$-1/cm$\^$-1/. The increase of the radiation-induced steady state current I$\^$c/, permittivity $\varepsilon$ and conductivity $\sigma$ with output(4.0 cGy/min, 8.5 cGy/min, 15.6 cGy/min, 19.3 cGy/min) was observed. A series of independent measurements were also performed to evaluate reproducibility and revealed less than 1% deviation in a day and 3% deviation in a long term. Charge and current showed the dependence on the interval between measurements, the smaller the interval was, the bigger the difference between initial reading and next reading was. At least in 20 minutes of next reading reached an initial value. It may indicate that the polymers were exhibiting an electret state for a while. These results can be explained by the internal polarization associated with the production of electron-hole pairs by secondary electrons, the change of conductivity and the equilibrium due to recombination etc. Heating to the sample made the reading value increase in a short time, it may be interpreted that the internal polarization was released due to heating and it contributed the number of charge carriers to increase when the samples was again irradiated. The linearity and reproducibility of the samples with the applied voltage and absorbed dose and a large amount of charge measured per unit volume compared with the other chambers give the feasibility of a radiation detector and make it possible to reduce the volume of a detector.

• Investigative Magnetic Resonance Imaging
• /
• v.12 no.2
• /
• pp.123-130
• /
• 2008

Purpose : Motion effects in parallel magnetic resonance imaging (MRI) are investigated. Parallel MRI is known to be robust to motion due to its reduced acquisition time. However, if there are some involuntary motions such as heart or respiratory motions involved during the acquisition of the parallel MRI, motion artifacts would be even worse than those in conventional (non-parallel) MRI. In this paper, we defined several types of motions, and their effects in parallel MRI are investigated in comparisons with conventional MRI. Materials and Methods : In order to investigate motion effects in parallel MRI, 5 types of motions are considered. Type-1 and 2 are periodic motions with different amplitudes and periods. Type-3 and 4 are segment-based linear motions, where they are stationary during the segment. Type-5 is a uniform random motion. For the simulation, Cartesian and spiral grid based parallel and non-parallel (conventional) MRI are used. Results : Based on the motions defined, moving artifacts in the parallel and non-parallel MRI are investigated. From the simulation, non-parallel MRI shows smaller root mean square error (RMSE) values than the parallel MRI for the periodic (type-1 and 2) motions. Parallel MRI shows less motion artifacts for linear(type-3 and 4) motions where motions are reduced with shorter acquisition time. Similar motion artifacts are observed for the random motion (type-5). Conclusion : In this paper, we simulate the motion effects in parallel MRI. Parallel MRI is effective in the reduction of motion artifacts when motion is reduced by the shorter acquisition time. However, conventional MRI shows better image quality than the parallel MRI when fast periodic motions are involved.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.4
• /
• pp.261-271
• /
• 2016

In the prediction of response of a pile in soil, numerical approaches such as a finite element method are generally applied due to complicate nonlinear behaviors of soils. However, the numerical methods based on the finite elements require heavy efforts in pile and soil modelling and also take long computing time. So their usage is limited especially in the early design stage in which principal dimensions and properties are not specified and tend to vary. On the contrary, theoretical approaches adopting linear approximations for soils are relatively simple and easy to model and take short computing time. Therefore, if they are validated to be reliable, they would be applicable in predicting responses of a pile in soil, particularly in early design stage. In case of wind turbines regarded in this study, it is required to assess their natural frequencies in early stages, and in this simulation the supporting pile inserted in soil could be replaced with a simplified elastic boundary condition at the bottom end of the wind turbine tower. To do this, analysis for a pile in soil is performed in this study to extract the spring constants at the top end of the pile. The pile in soil can be modelled as a beam on elastic spring by assuming that the soils deform within an elastic range. In this study, it is attempted to predict pile deformations and influence factors for lateral loads by means of the beam-on-spring model. As two example supporting structures for wind turbines, mono pile and suction pile models with different diameters are examined by evaluating their influence factors and validated by comparing them with those reported in literature. In addition, the deflection profiles along the depth and spring constants at the top end of the piles are compared to assess their supporting features.

• Radiation Oncology Journal
• /
• v.25 no.4
• /
• pp.227-232
• /
• 2007

Purpose: To investigate the flavopiridol effect on radiation-induced apoptosis and expression of apoptosisrelated genes of human laryngeal and lung cancer cells. Materials and Methods: A human laryngeal cancer cell line, AMC-HN3 and a human lung cancer cell line, NCI-H460, were used in the study. The cells were divided into four groups according to the type of treatment: 1) control groups; 2) cells that were only irradiated; 3) cells treated only with flavopiridol; 4) cells treated with flavopiridol and radiation simultaneously. The cells were irradiated with 10 Gy of X-rays using a 4 MV linear accelerator. Flavopiridol was administered to the media at a concentration of 100 nM for 24 hours. We compared the fraction of apoptotic cells of each group 24 hours after the initiation of treatment. The fraction of apoptotic cells was detected by measurement of the sub-G1 fractions from a flow cytometric analysis. The expression of apoptosis-regulating genes, including cleaved caspase-3, cleaved PARP (poly (ADP-ribose) polymerase), p53, p21, cyclin D1, and phosphorylated Akt (protein kinase B) were analyzed by Western blotting. Results: The sub-G1 fraction of cells was significantly increased in the combination treatment group, as compared to cells exposed to radiation alone or flavopiridol alone. Western blotting also showed an increased expression of cleaved caspase-3 and cleaved PARP expression in cells of the combination treatment group, as compared with cells exposed to radiation alone or flavopiridol alone. Treatment with flavopiridol down regulated cyclin 01 expression of both cell lines but its effect on p53 and p21 expression was different according to each individual cell line. Flavopiridol did not affect the expression of phophorylated Akt in both cell lines. Conclusion: Treatment with flavopiridol increased radiation-induced apoptosis of both the human laryngeal and lung cancer cell lines. Flavopiridol effects on p53 and p21 expression were different according to the individual cell line and it did not affect Akt activation of both cell lines.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.1
• /
• pp.40-49
• /
• 1999

A laboratory flume experiment, using turbulence-generating acryl tank and natural sediments, was conducted to investigate the effects of salinity, concentration of suspended sediment, turbulence and clay minerals on the flocculation and settling of fine-grained suspended sediments. While experiments were run, a sequence of water samples were taken near the bottom of the tank to analyze the variations of size distribution and relative contents of clay minerals. The results of the salinity experiment indicate that median settling velocity ($W_{50}$) increases linearly with salinity. Different settling processes of suspended sediments under variable concentrations appear to be predictable, depending upon the range of the suspension concentration. At concentrations less than 200 mg/l, $W_{50}$ is rarely varied with concentration probably because of the individual--grain settling mode. In the range of 200 to 13,000 mg/l show $W_{50}$ and concentration a good relationship following an empirical formula: $W_{50}=0.45C^{0.44}$. This relationship, however, no longer holds in concentrations exceeding 13,000 mg/l; instead, a more or less reverse one is shown. This result suggests an effect of hindered settling. The turbulence effect is somewhat different from that of concentration. Turbulence accelerates the flocculation and settling susepended sediments at low concentration (200 mg/l), whereas at high concentration turbulence breaks floes down and impedes the settling. Size distribution of suspended sediments sampled near the bottom of the tank tend to be more negatively skewed and leptokurtic in turbulent conditions compared to those in static conditions. The clay mineral analysis from the sequential water samples shows that over time the content of smectite decreases most rapidly with illite remaining concentrated in suspension. This means that smectite, among other clay minerals, plays the most effective role in the flocculation of fine-grained sediment in saline water.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.61 no.1
• /
• pp.70-77
• /
• 2016

The object of this study was to evaluate the effects of climatic elements on potato yield and create a model for estimating the potato yield. We used 35 yield data of Sumi variety produced in mulching cultivation from 17 regions over 11 years. According to the results, some climatic elements showed significant level of correlation coefficient with marketable yield of potato. Totally 22 items of climatic elements appeared to be significant. Especially precipitation for 20 days after planting (Prec_1 & 2), relative humidity during 11~20 days after planting (RH_2), precipitation for 20 days before harvest (Prec_9 & 10), sunshine hours during 50~41 days before harvest (SH_6) and 20 days before harvest (SH_9 & 10), and days of rain during 10 days before harvest (DR_10) were highly significant in quadratic regression analysis. 22 items of predicted yield ($Y_i=aX_i{^2}+bX_i+c$) were induced from the 22 items of climatic elements (step 1). The correlations between the predicted yields and marketable yield were stepwised using SPSS, statistical program, and we selected a model (step 2), in which 4 items of independent variables ($Y_i$) were used. Subsequently the $Y_i$ were replaced with the equation in step 1, $aX_i{^2}+bX_i+c$. Finally we derived the model to predict the marketable yield of potato as below. $$Y=-336{\times}DR_-10^2+854{\times}DR_-10-0.422{\times}Prec_-9^2+43.3{\times}Prec_-9\\-0.0414{\times}RH_-2^2+46.2{\times}RH_-2-0.0102{\times}Prec_-2^2-7.00{\times}Prec_-2-10039$$.

• Journal of Environmental Impact Assessment
• /
• v.26 no.6
• /
• pp.470-478
• /
• 2017

This study was classified into two groups, normal season group and drought season group, by the cluster analysis using the weather and water quality data from 2012 to 2015, using SPSS 18 version. Also each cluster was classified into three spaces, Gangcheon, Yeoju and Ipoh weir. We performed the multiple regression analysis with each monthly data that concentration of Chl-a was more than algae warming level. 6 groups classified in time and space were analyzed by the correlation analysis between concentration of Chl-a and 3 weather, 11 water quality and discharge factors. We developed Chl-a prediction equations of each group with independent variables of the multiple regression analysis applying to the correlation result. The result of cluster analysis was that the period was divided into two groups, normal group(2012-2013) that total annual precipitation rate was normal and drought group(2014-2015) that total annual precipitation rate was less than 1,000 mm/hr, in time. The months that concentration of Chl-a was more than algae warming level in each group classified by cluster analysis were that the normal group was 3~8 and drought group was 3 and 6~10. The correlation result between Chl-a and weather, water quality and discharge factors for each 6 group was that relationships between Chl-a and water, discharge factors were high in the drought group more than in normal group at all weirs. This was influenced by velocity reduction and increasing HRT according to the intense drought. Weather, water quality and discharge factors that were high correlation with Chl-a were applied to independent variables of Chl-a prediction equations and each equations were developed. Among them, Each adjusted R square of Prediction equations for Chl-a in each group at Ipoh weir where is located in Namhan river downstream and is directly connected to Paldang dam were normal group = 0.920 and drought group = 0.818. It's showed the high linear.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.5-9
• /
• 2004

In this paper, we studied the OCT(Optical Coherence Tomography) system which it has been extensively studied because of having some advantages such as high resolution cross-sectional images, low cost, and small size configuration. A basic principle of OCT system is Michelson interferometer. The characteristics of light source determine the resolution and the transmission depth. As a results, the light source have a commercial SLD with a central wavelength of 1,285 nm and FWHM(Full Width at Half Maximum) of 35.3 nm. The optical delay line part is necessary to equal of the optical path length with scattered light or reflected light from sample. In order to equal the optical path length, the stage which is attached to reference mirror is moved linearly by step motor And the interferometer is configured with the Michelson interferometer using single mod fiber, the scanner can be focused of the sample by using the reference arm. Also, the 2-dimensional cross-sectional images were measured with scanning the transverse direction of the sample by using step motor. After detecting the internal signal of lateral direction at a paint of sample, scanner is moved to obtain the cross-sectional image of 2-demensional by using step motor. Photodiode has been used which has high detection sensitivity, excellent noise characteristic, and dynamic range from 800 nm to 1,700 nm. It is detected mixed small signal between noise and interference signal with high frequency After filtering and amplifying this signal, only envelope curve of interference signal is detected. And then, cross-sectional image is shown through converting this signal into digitalized signal using A／D converter. The resolution of the OCT system is about 30$\mu\textrm{m}$ which corresponds to the theoretical resolution. Also, the cross-sectional image of ping-pong ball is measured. The OCT system is configured with Michelson interferometer which has a low contrast because of reducing the power of feedback interference light. Such a problem is overcomed by using the improved inteferometer. Also, in order to obtain the cross-sectional image within a short time, it is necessary to reduce the measurement time for improving the optical delay line.

• Journal of Life Science
• /
• v.17 no.2 s.82
• /
• pp.218-222
• /
• 2007

The purpose of this study is to evaluate the relationship between high sensitive C-reactive protein (hsCRP) and pulse transit time (PPT). Apparently healthy 233 subjects had been enrolled in the health promotion center of the Pusan National University Hospital from Jan. 29 to Feb. 26, 2004. They had no previous history of diabetes, hypertension and hyperlipidemia. Subjects were categorized according to tertiles of hsCRP level [Group 1: first tertile $(0.01\;{\sim}\;0.02\;mg/dl)$, Group 2: second tertile $(0.03\;{\sim}\;0.05\;mg/dl)$, Group 3: third tertile $(0.06\;{\sim}\;0.12\;mg/dl)$, and Group 4: Fourth tertile $(0.13\;{\sim}\;16.8\;mg/dl)$]. PTT body mass index (BMI), total cholesterol (T-C), LDL-cholesterol(LDL-C), blood sugar (BS), systolic blood pressure (sBP) and diastolic blood pressure (dBP) were significantly different among hsCRP groups (p<0.05). HsCRP is positively related with BMI, tryglyceride (TG), LDL, sBP and dBP (p<0.05), and negatively related with PTT and HDL-cholesterol (HDL-C) (p<0.05). PTT is significantly negatively related with hsCRP, T-C, TG, LDL-C, BS, dBP and sBP (p<0.05). The hsCRP and PTT were related before controlling BMI, T-C, LDL-C, sBP, and dBP, but not related after conkolling. The relationship between hsCRP and PTT depends on cardiovascular disease risk factors.

• Journal of Radiation Protection and Research
• /
• v.40 no.4
• /
• pp.194-201
• /
• 2015

We have investigated the EPR signal properties in 12 components of two mobile phones (LCD, OLED) using electron paramagnetic resonance (EPR) spectrometer in this study.EPR measurements were performed at normal atmospheric conditions using Bruker EXEXSYS-II E500 spectrometer with X-band bridge, and samples were irradiated by $^{137}Cs$ gamma-ray source. To identify the presence of radiation-induced signal (RIS), the EPR spectra of each sample were measured unirradiated and irradiated at 50 Gy. Then, dose-response curve and signal intensity variating by time after irradiation were measured. As a result, the signal intensity increased after irradiation in all samples except the USIM plastic and IC chip. Among the samples, cover glass(CG), lens, light guide plate(LGP) and diffusion sheet have shown fine linearity ($R^2$ > 0.99). Especially, the LGP had ideal characteristics for dosimetry because there were no signal in 0 Gy and high rate of increase in RIS. However, this sample showed weakness in fading. Signal intensity of LGP and Diffusion Sheet decreased by 50% within 72 hours after irradiation, while signals of Cover Glass and Lens were stably preserved during the short period of time. In order to apply rapidly EPR dosimetry using mobile phone components in large-scale radiation accidents, further studies on signal differences for same components of the different mobile phone, fading, pretreatment of samples and processing of background signal are needed. However, it will be possible to do dosimetry by dose-additive method or comparative method using unirradiated same product in small-scale accident.