• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.5
• /
• pp.552-560
• /
• 2013

In this paper, an optimization algorithm for the block assembly accuracy control assessment is proposed with consideration for the current block assembly process and accuracy control procedure used in the shipbuilding site. The objective function of the proposed algorithm consists of root mean square error of the distances between design and measured data of the other control points with respect to a specific point of the whole control points. The control points are divided into two groups: points on the control line and the other points. The grouped data are used as criteria for determining the combination of 6 degrees of freedom in the registration process when constituting constraints and calculating objective function. The optimization algorithm is developed by using combination of the sampling method and the point to point relation based modified ICP algorithm which has an allowable error check procedure that makes sure that error between design and measured point is under allowable error. According to the results from the application of the proposed algorithm with the design and measured data of two blocks data which are verified and validated by an expert in the shipbuilding site, it implies that the choice of whole control points as target points for the accuracy calculation shows better results than that of the control points on the control line as target points for the accuracy of the calculation and the best optimized result can be acquired from the accuracy calculation with a fixed point on the control line as the reference point of the registration.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.239-247
• /
• 2008

Use of both carbon fiber (CF) and glass fiber (GF) at the same time to strengthen existing flexural members was exploited. Using a proper volumetric GF / CF ratio, the CF can rupture first followed by subsequent rupture of GF at higher stress and strain showing a pseudo-ductile behavior. A theoretical study indicated that the ratio is 4.62 : 1 and higher where the pseudoductile effect can be shown. Flexural tests of plain concrete beams strengthened using fibers were first carried out. Hybrid FRP sheet using 8.8 : 1 ratio was then fabricated and the sheet was used to strengthen reinforced concrete beams. The RC beams strengthened using 1-ply and 2-ply hybrid sheets both revealed increased strength over a non-strengthened beam and ductile flexural behavior. A comparable beam strengthened using CF also showed increased strength but with limited ductility.

• Proceedings of the Korean Information Science Society Conference
• /
• 2003.10b
• /
• pp.415-417
• /
• 2003

본 논문에서는 휴대폰에서 실시간으로 사용할 수 있는 GIS 기반의 약도를 생성하는 기법을 소개한다. 휴대폰의 출력 창은 크기가 제한되어, 자세한 도로 정보들이나 건물 정보 등의 GIS 정보를 모두 출력 창에 표현하면 사용자들이 인식하기가 매우 어렵다. 그러므로, 출력창의 크기에 맞춘 간략한 약도를 제공하여 사용자들이 지리 정보를 손쉽게 활용할 수 있도록 도와주자는 것이다. 기존의 GPS와 지리 정보를 이용한 경로 탐색 및 안내 장비는 차량 운전자를 위한 도로 중심의 지리 정보를 제공한다. 우리나라 도로 환경에서는 휴대폰을 가진 보행자가 장소 찾기에 필요한 지리 정보를 원하는 경우도 않다. 그러므로 본 연구에서는 도보 통행자 및 대중교통 사용자들이 이용하기 편리하도록 지하철역이나 버스 정류장, 대형건물과 같은 이정표를 중심으로 하고. 장소 찾기에 필요한 도로만을 출력 창에 나타내어 단순화된 지리정보를 제공하고자 한다. 또한, 기존에 사용하던 방위 개념 중심의 지도들을 가지고, 지도 읽기에 익숙하지 않은 일반 보행자들이 길 찾기에 바로 사용하는 것은 쉽지 않다. 그러므로 수직 개념을 이용한 단순화된 도로 표현 기법을 사용하여 일반인도 쉴게 지도를 보고 길을 찾을 수 있도록 하였다. GIS 정보 중에서 필요로 하는 도로들을 선택하여 그 경로들을 수직선과 수평선에 가깝게 변형하고, 불필요한 도로를 생략, 지도를 단순화하였다. 또한 포함되어 있던 많은 정보들 중에서 일반적으로 보행자들이 길을 찾아갈 때에 참고하는 정보들을 제외한 나머지 정보들을 생략함으로써, 불필요한 정보로 인한 지도의 복잡도를 줄이고, 지리 정보의 가독성을 향상시켰다. 본 연구의 결과를 활용하면 휴대폰의 출력 창에는 이정표 중심의 약도를 표현할 수 있으므로, 약도 정보를 실시간으로 서비스할 수 있을 것으로 기대된다.성뿐만 아니라 보안성을 중요하게 생각하였으며, 앞으로 보안 관련 소프트웨어 개발에 사용될 수 있는 도구들이 가이드 라인에 대한 정보를 제공한다.용할 수 있는지 세부 설계를 제시한다.다.으로서 hemicellulose구조가 polyuronic acid의 형태인 것으로 사료된다. 추출획분의 구성단당은 여러 곡물연구의 보고와 유사하게 glucose, arabinose, xylose 함량이 대체로 높게 나타났다. 점미가 수가용성분에서 goucose대비 용출함량이 고르게 나타나는 경향을 보였고 흑미는 알칼리가용분에서 glucose가 상당량(0.68%) 포함되고 있음을 보여주었고 arabinose(0.68%), xylose(0.05%)도 다른 종류에 비해서 다량 함유한 것으로 나타났다. 흑미는 총식이섬유 함량이 높고 pectic substances, hemicellulose, uronic acid 함량이 높아서 콜레스테롤 저하 등의 효과가 기대되며 고섬유식품으로서 조리 특성 연구가 필요한 것으로 사료된다.리하였다. 얻어진 소견(所見)은 다음과 같았다. 1. 모년령(母年齡), 임신회수(姙娠回數), 임신기간(姙娠其間), 출산시체중등(出産時體重等)의 제요인(諸要因)은 주산기사망(周産基死亡)에 대(對)하여 통계적(統計的)으로 유의(有意)한 영향을 미치고 있어 $25{\sim}29$세(歲)의 연령군에서, 2번째 임신과 2번째의 출산에서 그리고 만삭의 임신 기간에, 출산시체중(出産時體重) $3.50{\sim}3.99kg$사이의 아이에서 그 주산기사망률(周産基死亡率)이 각각 가장 낮았다. 2. 사산(死産)과 초생아사망(初生兒死亡)을 구분(區分)하여 고려해 볼때 사산(死産)은 모성(母性)의 임신력(姙娠歷)과 매우 밀접한 관련이 있는 것으로 사료(思料)되었고 초생아사망(初生兒死

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.167-167
• /
• 2013

최근에 산화물 형광체는 황화물 형광체에 비해 높은 화학적 안정성을 나타내기 때문에 백색 발광 다이오드, 전계방출 디스플레이와 플라즈마 디스플레이 패널에 그 응용성을 넓히고 있다. 마그네슘 니오베이트(magnesium niobate, MgNb2O6)는 우수한 유전 특성(상대 유전상수=18.4)을 나타내기 때문에 마이크로파 유전체로 응용 가능하며, 단일상 릴랙서 페라브스카이트(relaxor perovskite) Pb(Mg1/3Nb2/3)O3을 합성하기 위한 전구체 (precursor)로 널리 사용되고 있으며, 나이오븀산염 이온에서 다양한 색상을 방출하는 활성제 이온으로 효율적인 에너지 전달이 일어남으로써 Sm3+, Dy3+, Eu3+와 같은 희토류 이온의 좋은 모체 격자로 개발할 수 있다. 본 연구에서는 마그네슘 니오베이트 MgNb2O6 모체 결정에 다양한 활성제 이온, 즉 Eu3+, Sm3+, Dy3+, Tb3+를 선택적으로 주입하여 발광 효율이 높은 천연색 형광체를 합성하고자 한다. 특히, 모체 결정에 주입되는 활성제 이온 주위의 국소적인 환경이 반전 대칭에서 변형되는 척도를 조사하여 활성제의 주 발광 파장의 세기가 최대가 되는 최적의 조건을 결정하고자 한다. Mg1-1.5xNb2O6:REx3+ 형광체 분말 시료는 초기 물질 MgO, Nb2O5와 희토류 이온을 화학 반응식에 맞게 정밀 저울로 측량하여 플라스틱 용기에 ZrO2 볼과 함께 넣고, 소정의 에탄올을 채운 뒤 밀봉하고서, 300 rpm의 속도로 20시간 볼밀 (ball-mill) 작업을 수행하였다. 그 후, 체(sieve)로 ZrO2 볼을 걸러낸 다음에 혼합된 용액을 각 비커에 담아서 $40^{\circ}C$의 건조기에서 24시간 건조하였고, 건조된 시료를 막자 사발에 넣고 잘게 갈고 80 ${\mu}m$의 체로 걸러낸 후에, 알루미나 도가니에 활성제 이온별로 각각 담아, 전기로에 장입하여 매분당 $5^{\circ}C$의 비율로 온도를 상승시켜 $350^{\circ}C$에서 5시간 동안 하소 공정을 실시한 후에, 온도를 계속 일정한 율로 증가시켜 $1,200^{\circ}C$에서 5시간 동안 소성하여 합성하였다. 합성된 형광체 분말의 결정 구조는 $Cu-K{\alpha}$ 복사선(파장: 1.5406)을 사용하여 X-선회절장치로 측정하였으며, 형광체의 표면 형상은 전계형 주사전자현미경으로 관측하였다. 흡광와 발광스펙트럼은 제논 램프를 광원으로 갖는 형광 광도계를 사용하여 측정하였다. 모체 결정에 활성제 이온 Eu3+, Sm3+, Dy3+, Tb3+가 도핑된 형광체 분말은 각각 적색, 주황색, 황색, 녹색 발광이 관측되었다. 각 발광 스펙트럼과 결정 입자의 크기와 형상 사이의 상호 관계를 조사하였다. 실험 결과로부터, 각 형광체의 발광 파장은 활성제 이온의 종류 와 서로 밀접하게 관련되어 있으며, 형광체 시료 합성시 활성제 이온의 농도를 선택적으로 조절함으로써 발광의 세기를 제어할 수 있음을 확인하였다.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.253-260
• /
• 1993

High strength and fracture toughness of Al-Li-Cu alloy(2090 Al alloy) have been achieved by the improvement of melting and casting, extrusion and heat treatment techniques. To establish the sucessful process for semi-industrial scale ingot(20Kg) the following areas have been investigated: (1) Improvement of melting and casting techniques for ingot by introducing atmospheric modifications, vacuum and rotary degassing, and deslagging. (2) The effect of heat treatment on mechanical properties (3) Mechanical characterization by tensile test, fracture toughness test and fatigue crack propagation test. High mechanical properties were found to be intimately related with ingot soundness. Tensile strength of final products varied from 534MPa to 566MPa in peak aged condition while elongation/ductility ranged from 9.0% to 11.9%. From the fracture toughness test with using compact tensile specimen, plane strain fracture toughness($K_{Ic}$) appeared to be 39MPa${\surd}$m in peak aged condition and 23MPa${\surd}$ m in underaged condition. When load ratios of 0.1, 0.3 and 0.5 were given ${\Delta}K_{th}$ was 6.0MPa${\surd}$ m, 5.3MPa${\surd}$ m and 4.3MPa${\surd}$ m respectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.1
• /
• pp.62-68
• /
• 2001

In order to characterize the microscopic fracture behaviour of the weldment din stress corrosion cracking(SCC) phenomena, SCC and acoustic emission(AE) tests were carried out simultaneously and the correlation between mechanical paramenters obtained from SCC and AE tests was investigated. In the case of base metal, much more AE events were produced at -0.5V than at -0.8V because of the dissolution mechanism before the maximum load. Regardless of the applied voltages to the specimens, however, AE events decreased after the maximum load. In the case of weldment, lots of AE events with larger amplitude $range(40{\sim}100dB)$ were produced because of the singularities of weld HAZ in comparision to the base metal and post-weld heat-treated(PWHT) specimens. Numerous and larger cracks for the weldment were observed on the fractured surfaces by SEM examination. From these results, it was concluded that SCC for the weldment appeared most severely in synthetic seawater. Weld HAZ was softened by PWHT which also contributed to the reduced susceptibility to corrosive environment in comparison to the weldment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.305-312
• /
• 2007

Among many types of light rail transits (LRT), the rubber-tired automated guide-way transit (AGT) is prevalent in many countries due to its advantages such as good acceleration/deceleration performance, high climb capacity, and reduction of noise and vibration. However, AGT is generally powered by high-voltage electric power feeding system and it may cause electromagnetic interference (EMI) to measurement sensors. The fiber optic sensor system is free from EMI and has been successfully applied in many applications of civil engineering. Especially, fiber Bragg grating (FBG) sensors are the most widely used because of their excellent multiplexing capabilities. This paper investigates a prestressed concrete girder bridge in the Korean AGT test track using FBG based sensors to monitor the dynamic response at various vehicle speeds. The serviceability requirements provided in the specification are also compared against the measured results. The results show that the measured data from FBG based sensors are free from EMI though electric sensors are not, especially in the case of electric strain gauge. It is expected that the FBG sensing system can be effectively applied to the LRT railway bridges that suffered from EMI.

• Journal of radiological science and technology
• /
• v.44 no.5
• /
• pp.443-449
• /
• 2021

In this study, the purpose is to present the foot inclination angle for realizing an image similar to that of the existing examination method and to present the clinical usefulness of the new examination method through comparison between the existing examination method and the newly designed standing foot oblique projection. A foot phantom was used, and the magnification of the image according to the angle was quantitatively evaluated by attaching a nut to the position of the cuboid of the phantom. The internal oblique image acquired using a 30° wedge was set as the standard image. And that image was compared with the images acquired by changing the angle of the foot from 20° to 65° at intervals of 5°. Image evaluation was performed by 3 radiological technologists, and qualitative evaluation using a Likert 5-point scale for evaluation items of true oblique view and quantitative evaluation of the value obtained by measuring the diameter of a nut in each image were performed as image evaluation. For data analysis, reliability analysis between the measure and comparative analysis of the average value for each angle were performed. The qualitative evaluation score for each image was 4.5 to 5 points for most questions in the case of the standard image. And 4 points or less for most questions in the images with a foot angle of 45° or less, and an evaluation score close to the standard image was obtained in the image of 50° or more. And in the quantitative evaluation, the diameter of the nut was measured to be 9.28~9.56 mm. The qualitative evaluation showed a reliability of 0.95~1.0 and the quantitative evaluation was 0.62. As a result of comparing and analyzing the average of the quantitative and qualitative average values for each angle image, the group with the average value most similar to the standard image was images obtained at 55° and 60°, and in the post-analysis, the images of both groups were the same group as the standard image(p<0.01). As a result of this study, it was found that the angle of inclination of the foot for realizing the image most similar to the existing image in the standing foot oblique projection is 55°~60°. In addition, if this test method is applied to the clinic, it is believed that it will help prevent safety accidents such as falls during the test and improve test efficiency by minimizing the movement of patients for the test.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.2
• /
• pp.411-417
• /
• 2021

The field that studies human-computer interaction is called HCI (Human-computer interaction). This field is an academic field that studies how humans and computers communicate with each other and recognize information. This study is a study on hand gesture recognition for human interaction. This study examines the problems of existing recognition methods and proposes an algorithm to improve the recognition rate. The hand region is extracted based on skin color information for the image containing the shape of the human hand, and the center of gravity profile is calculated using principal component analysis. I proposed a method to increase the recognition rate of hand gestures by comparing the obtained information with predefined shapes. We proposed a method to increase the recognition rate of hand gestures by comparing the obtained information with predefined shapes. The existing center of gravity profile has shown the result of incorrect hand gesture recognition for the deformation of the hand due to rotation, but in this study, the center of gravity profile is used and the point where the distance between the points of all contours and the center of gravity is the longest is the starting point. Thus, a robust algorithm was proposed by re-improving the center of gravity profile. No gloves or special markers attached to the sensor are used for hand gesture recognition, and a separate blue screen is not installed. For this result, find the feature vector at the nearest distance to solve the misrecognition, and obtain an appropriate threshold to distinguish between success and failure.

• Cross-Cultural Studies
• /
• v.45
• /
• pp.7-32
• /
• 2016

This article considers the meaning of 'Zainichi (在日)' expressed in epic poem Niigata (1970) written by Korean-Japanese poet Kim Shi Jong. Kim sets two points in his creation of poetry. One is summer of liberation released from Japanese colonial domination in 1945. The other is Japan where he lives as a Korean-Japanese. These two points have made him think about the meaning of living in post-colonial era and the national division of Korea, his home country. His thought like this is well expressed in his epic Niigata. Niigata was written in 1959 when the ship returning to North Korea departed from Niigata of Japan. However, Kim couldn't return to his home country at that time. He stowed away from South Korea to Japan in 1949. He participated in antigovernment activities occurred in Jeju Island to block the national division between the south and the north after the liberation in 1945, the so-called 4.3 incident. Besides, he was having conflict with the organization of North Korea at that time because it required a doctrinaire belief and creation in Korean. Kim was writing poems in Japanese and pursued the life of existence as a Korean-Japanese. Therefore, he decided to remain in Japan instead of returning to North Korea. Of course, he could not return to South Korea because he was a refugee. Kim imagined in Niigata, the place located in an extension of the 38th parallel and the spot of national division. He could not cross the division line when he was in his home country, but he could do it in Niigata through imagination. The life as a Korean-Japanese makes it possible. 'Zainichi', which means living in Japan, has been recognized as a worse situation compared to living in Korea. However, Kim changed his way of thinking. Zainichi can embrace South Korea, North Korea, and Japan. This is the very reason why he lives there as a Korean-Japanese. His thought like this is well expressed by symbolic representations and metamorphose as well as the imagination of spatial extension.