• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2023.05a
• /
• pp.270-271
• /
• 2023

해양 4차 산업 도래에 맞춰 기존 항로표지 역할에 ICT 기술을 융합하여 근거리에서 통신을 활용하여 항로표지의 점검 및 관리시스템 개발의 요구가 있다. 항로표지 점검 시 관리자들의 편의와 점검을 위하여 선박 접안 사고 예방 등 근거리 통신을 적용한 장비 점검 시스템 개발이 필요하다.. 본 논문에서는 현황 분석을 통하여 근거리 점검 시스템 설계 방향을 제시하였다. 다양한 분야에서 무선 통신을 활용한 점검 및 모니터링 기술을 분석하여 시스템 구성 방향을 제시하였고, 현재 운영중인 항로표지 관리운영 시스템을 분석하여 점검을 위하여 표출할 정보를 검토하였다. 향후 설계 방향을 바탕으로 시스템을 개발하고 성능 평가를 수행할 예정이며, 관리의 편의를 위하여 정보협력센터에 제공할 이력 정보를 검토할 예정이다.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.1
• /
• pp.62-67
• /
• 2018

A wave buoy commonly used for measurements in marine environments is very useful for measurements on the sea surface wind and waves. However, it is constantly exposed to external forces such as typhoons and the risk of accidents caused by ships. Therefore, the installation and maintenance charges are large and constant. In this study, we developed a system for monitoring the sea surface wind using marine radar to provide spatial and temporal information about sea surface waves at a small cost. The essential technology required for this system is radar signal processing. This paper also describes the analytical process of using it for monitoring the sea surface wind. Consequently, developing this system will make it possible to replace wave buoys in the near future.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.2
• /
• pp.1-9
• /
• 2012

In this paper, we design and implement a DCS (Distributed Control System) based on dual field-bus for ship engine. For monitoring and controlling the condition of the ship engine, an implemented DCS is consisted of two-tier communication structure by using CAN (Controller Area Network) and MODBUS protocols. The first-tier is consisted of CAN protocol for sharing the condition of the ship engine by each implemented monitoring system. By using MODBUS protocol, the second-tier is used for communicating the monitoring data from an implemented DCS to AMS(Alarm Monitoring System). We verified and tested our scheme and implemented DCS by KR (Korea Register) technical rules through experimental tests.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.502-504
• /
• 2021

The application area based on UAV(Unmanned Aerial Vehicle) is continuously increasing as time passing by. In particular the UAVs which consist of more than four horizontal propellers and the functionality of VTOL (Vertical Take-Off and Landing) are utilized in diverse platforms and application products due to their safety and aerodynamically simpler design and architectures. Most UAV missions are controlled by GCSs(Ground Control System). The GCSs are generally connected to the internet and get electrical map and environmental information such as temperature, humidity, wind direction and so on. In this paper, we design a system that UAV has capability of approaching to a certain ship and monitoring her efficiently by using AIS(Auto Identification System) information.

• Economic and Environmental Geology
• /
• v.49 no.4
• /
• pp.281-290
• /
• 2016

Coastal areas, used as human utilization areas like leisure space, medical care, ports and power plants, etc., are regions that are continuously changing and interconnected with oceans and land. Regular monitoring of coastal changes is essential at key locations with such volatility. But the survey method of terrestial LiDAR(Light Detection and Ranging) system has much time consuming and many restrictions. For effective monitoring coastal changes, KIOST(Korea Institute of Ocean Science & Technology) has constructed a shipborne mobile LiDAR system. The shipborne mobile LiDAR system, installed in a research vessel, comprised a land based LiDAR(RIEGL LMS-420i), an IMU(MAGUS Inertial+), a RTKGNSS(LEICA GS15 GS25), and a fixed platform. The shipborne mobile LiDAR system is much more effective than a land based LiDAR system in the measuring of fore shore areas without shadow zone. Because the vessel with the shipborne mobile LiDAR system is continuously moved along the shoreline, it is possible to efficiently survey a large area in a relatively short time. We conducted test measurements in the Anmok-Songjung beach around the Gangneung port. Effective monitoring of the changes using the constructed shipborne mobile LiDAR system for seriously eroded coastal areas will be able to contribute to coastal erosion management and response.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.519-526
• /
• 2018

In this study, an algorithm to predict evacuation routes in support of shipboard lifesaving activities is presented. As the first step of algorithm development, the feasibility and necessity of an evacuation route prediction algorithm are shown numerically. The proposed algorithm can be explained in brief as follows. This system continuously obtains and analyzes passenger movement data from the ship's monitoring system during non-disaster conditions. In case of a disaster, evacuation route prediction information is derived using the previously acquired data and a prediction tool, with the results provided to rescuers to minimize casualties. In this study, evacuation-related data obtained through fire evacuation trials was filtered and analyzed using a statistical method. In a simulation using the conventional evacuation prediction tool, it was found that reliable prediction results were obtained only in the SN1 trial because of the conceptual and structural nature of the tool itself. In order to verify the validity of the algorithm proposed in this study, an industrial engineering tool was adapted for evacuation characteristics prediction. When the proposed algorithm was implemented, the predicted values for average evacuation time and route were very similar to the measured values with error ranges of 0.6-6.9 % and 0.6-3.6 %, respectively. In the future, development of a high-performance evacuation route prediction algorithm is planned based on shipboard data monitoring and analysis.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.06a
• /
• pp.218-219
• /
• 2022

The Korea Institute for Advancement of Technology and the Ulsan ICT Promotion Agency are building an electric smart ship using a full range of ICT with advanced technology, and are expected to demonstrate it in 2022. For the demonstration of onboard ship equipment, it needs to develop a demonstration procedure. There are 4 types of onboard equipment preferentially selected for the development of the demonstration test procedure which are an electronic chart display and information system, a ship RADAR system, a voyage data recorder, and a ship energy efficiency monitoring system. This paper describes the demonstration procedure based on the equipment standard for the electronic chart display and information system among 4 selected types of demonstration equipment, and also the verification test checklist and template is introduced.

• Korean Journal of Remote Sensing
• /
• v.37 no.3
• /
• pp.559-566
• /
• 2021

It is necessary to quickly detect and respond to ship accidents that occur continuously due to the influence of the recently increased maritime traffic. For this purpose, ship detection research is being actively conducted based on satellite images that can be monitored in real time over a wide area. However, there is a possibility that the wake may be falsely detected as a ship because the wake removal is not performed in previous studies that performed ship detection using spectral characteristics. Therefore, in this study, ship detection was performed using SDI (Ship Detection Index) based on the Sentinel-2A satellite image, and the wake was removed by utilizing the difference in the spectral characteristics of the ship and the wake. Probability of detection (POD) and false alarm rate (FAR) indices were used to verify the accuracy of the ship detection algorithm in this study. As a result of the verification, POD was similar and FAR was improved by 6.4% compared to the result of applying only SDI.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2327-2332
• /
• 2011

Recently, the increase of loading amount on cargo ships due to the automation of loading process results in much complex ship operation. For this reason, NMEA-0183 based on RS-422,485 and NMEA-2000 based on CAN communication methods have been usually used as a standardized method in the marin electric interfacing equipments. In this paper, a general NMEA-0183 protocol was designed to support 7-channel NMEA-0183 serial communication data, which can receive 3-channel 16 bits ADC and 2-channel pulse using SPI(Serial Peripheral Interface). In particular, this method was designed for ship communication requires 7 important factors. Also in this study, using the minimization of the proposed method and realizing the monitoring system based on PC, the effectiveness of multichannel indicator system was proposed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.929-932
• /
• 2013

In preperation for the compulsory installation of VHF(Very High Frequency) wireless equipment and fishing vessel automatic identification system according to the revision of "The Ships Safety Act" and "Fishing Vessel act", Fishery Information & Communication Department of National Federation of Fisheries Cooperatives is building VHF communication network and automatic identification system for fishing vessel monitoring. This study suggests the protocol analysis for the calling of location requirement using DSC(Digital Selective Calling) function and show best way for fishing vessel automatic identification system. Also, it suggest way to realize fishing vessel monitoring system.