• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.400-413
• /
• 2016

The horizontal shear capacity when the flange of a steel girder is replaced with 80 MPa concrete is important for its structural safety. In this study, 6 specimens with different interface conditions were designed and fabricated based on the Limit State Design Code on Korean Highway Bridges and static tests were performed to measure the horizontal shear capacity. Not only the resistance factors of the stud shear connector, concrete and reinforcement, but also the surface conditions of the casing concrete and spacing of the horizontal shear reinforcements were used as the experimental variables. The experiments showed that the interfaces between the steel girder and the concrete flange have stronger joint performance than those between the concrete flange and deck slab. To ensure the composite action in the plastic zone, the conservative horizontal shear reinforcement is more important than the roughness in the concrete face.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.1000-1005
• /
• 2003

The shock separation test simulates the environmental effects of the spacecraft separation from launch vehicle. The shock separation test for a structural model of KOMPSAT-Ⅱ(Korea Multi-Purpose SATellite Ⅱ) was performed in SITC(Satellite Integration ＆ Test Center) launch environmental test hall at KARI(Korea Aerospace Research Institute) to verify the shock test requirement of the spacecraft, to predict the induced acceleration responses on the primary structures and payloads by the explosion of pyre-lock and to perform mechanical fit check. The spacecraft with S/A was mated vertically to LV(Launch Vehicle) adapter simulator via a clamp band, then hoisted and suspended above a foam test bed by four isolation springs secured to the spacecraft hoist fittings to isolate the payload platform shock wave from the sling elements. For separation process, real pyre-devices were used and the time response signals from 60 accelerometers installed on the interested points was acquired and recorded. The SRS responses for each response channels were calculated and the achieved SRS's on the separation plane was reviewed and evaluated in comparison to the ICD(Interface Control Document) value.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.147-155
• /
• 2006

In this paper, we propose a new Mushroom-like PBG concepts for designing with forbidden frequency band-gap at low frequency. These design rules are based on enhancing the capacitance per unit area using modified top-patch of mushroom PBG with no increase on the overall thickness of the substrate board. Also, in this paper, a new approach to suppress the surface wave from antenna is proposed by embedding compact mushroom PBG in the substrate. Comparisons between the results from a conventional patch antenna to a patch antenna on a PBG substrate show that the reduction in the surface wave level is remarkable. This can be observed in the radiation pattern and the maximum gain. The maximum gain for reference patch antenna is $6.43dB{\imath}$ at 5.37 GHz, while the maximum gain for the patch antenna with normal mushroom and vane mushroom PBG is $7.24dB{\imath}\;and\;7.53dB{\imath}$at 5.14 GHz. The back radiation is also considerably reduced; this will lead, of course, to an increase in the antenna efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.613-623
• /
• 2012

In this paper, we present an ultra miniaturized voltage tuned oscillator, with HMIC-type amplifier and phase shifter, using LTCC artificial dielectric resonator. ADR which consists of periodic conductor patterns and stacked layers has a smaller size than a dielectric resonator. The design specification of ADR is obtained from the design goal of oscillator. The structure of the ADR with a stacked circular disk type is chosen. The resonance characteristic, physical dimension and stack number are analyzed. For miniaturization of ADRO, the ADR is internally implemented at the upper part of the LTCC substrate and the other circuits, which are amplifier and phase shifter are integrated at the bottom side respectively. The fabricated ADRO has ultra small size of $13{\times}13{\times}3mm^3$ and is a SMT type. The designed ADRO satisfies the open-loop oscillation condition at the design frequency. As a results, the oscillation frequency range is 2.025~2.108 GHz at a tuning voltage of 0~5 V. The phase noise is $-109{\pm}4$ dBc/Hz at 100 kHz offset frequency and the power is $6.8{\pm}0.2$ dBm. The power frequency tuning normalized figure of merit is -30.88 dB.

• Design & Manufacturing
• /
• v.14 no.2
• /
• pp.42-48
• /
• 2020

This study is on the injection molding analysis for the LED outdoor lighting top cover of one heat sink body type structure. Thermoplastic and thermosetting resins were applied to compare the thermal properties during the injection molding process. The thermoplastic resin is used in this study due to special characteristics that it is light, good strength and dose long not transmute quality even if pass long time. The thermosetting resin is applied to this study due to good in strength, lightweight and excellent etc, thermal conductivity. This study presented a preliminary analysis of fill time, weld line, air trap etc. for the injection molding process of LED lamp cover and body through simulation using Moldflow. As a result of the study, it was selected HTM-102 material because the thermosetting resin has excellent strength and heat conductivity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.365-366
• /
• 2009

Humidity curing of the concrete after placing is significant to ensure the crack resistance, strength, and durability. Generally, there are watering and sheet curing methods as humidity curing methods to the upper part of slab concrete, therefore this study investigates effects of these curing methods to preservation of humidity on the cement mortar.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.171-172
• /
• 2009

A Bonded Concrete Overlay is a layer of concrete bonded to the top of an existing pavement to rehabilitate it, to restore and increase its structural and functional capabilities and forming a monolithic structure with the existing pavement. This study focuses on the field application of BCO by very early strength latex modified concrete.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.08a
• /
• pp.156-157
• /
• 2000

낮은 도핑의 silicon은 광통신에서 사용하는 1.3 및 1.55 um의 광파장 영역에서 0.01dB/cm 이하의 낮은 흡수 손실을 가짐으로 인해, core 층으로 silicon을 사용하며 상부 및 하부 cladding 층으로 SiO$_2$와 같은 유전체 박막 구조를 갖는 SOI (Silicon on Insulator)를 사용한 수동광소자에 대한 연구가 1990년대부터 진행되고 있다. 또한 silicon의 특성상 SOI는strain에 의한 영향이 낮고, 광학적 비등방성이 적어서 polymer 및 silica를 이용한 광소자에 비해 편광의존도가 낮은 광소자를 구현할 수 있는 장점이 있다. 현재까지 연구되어온 SOI 수동광소자의 연구결과는 TE/TM 편광차에 따른 채널분리도가 약 0.04nm, 누화특성이 23dB 인 8채널 AWG의 연구결과가 있었으며, 스위칭시간 < 1msec, 소광비 17 dB의 광결합기와 마하젠더가 혼합된 광변조기 및 Bookham사에서 개발한 RX/TX 양방향 송수신 광모듈에 적용된 1.3/l.55 um 파장선택적 분리기, Silicon-CMOS 증폭기와 집적화된 4channel 광다중 수신기등에 대한 연구결과가 있었다. (중략)

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.607-607
• /
• 2013

차세대 비휘발성 메모리 소자로서 각광받고 있는 저항 변화 메모리(resistive switching random access memory; ReRAM) 소자는 속도가 빠르고, 에너지 소모가 적으며, 고집적화를 이루기 용이하다는 강점을 보유하고 있다. 지금까지 저항변화 물질의 최적화를 위해 매우 다양한 물질들이 연구되고 있으며, 그 물질에 따라 스위칭 메커니즘 및 동작 방법이 다르게 보고되어 왔다. 하지만 저항변화 메모리의 스위칭 거동은 전형적인 전기적 제어 조건으로부터 구현되었기 때문에 한정된 소자 특성을 나타낼 수밖에 없었다. 본 연구에서는 새로운 메모리 제어 조건으로 빛을 이용함으로써 한정된 소자 특성으로부터 벗어나고자 하였다. 저항 변화 물질로 잘 알려진 ZnO를 표면적이 넓은 형태로 합성하기 위하여 hydrothermal 방법으로 FTO 기판 위에 수직하게 배열된 ZnO 나노와이어를 형성하고 그 위에 Au 상부 전극을 형성하여 금속-절연체-금속 소자 구조를 제작하였다. 본 연구에서는 전형적인 전기적 제어 조건에 더불어 빛의 입사 유무 조건을 바꿔가면서 Au/ZnO 나노와이어/FTO 소자의 저항 변화 특성을 평가 하였을 뿐만 아니라 전기적 인가 없이 오직 빛만으로 두 가지 안정한 저항 상태를 반복적으로 전환하는 특성을 유도하였다. 본 결과를 바탕으로 필라멘트 이론에 기초한 저항 변화 메커니즘을 설명하는 모델이 제시되었다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.2
• /
• pp.119-127
• /
• 2012

Purpose: This study was performed to compare the stress distribution pattern of abutment-fixture connection area using 3-dimensional finite element model analysis when 5 different implant systems which have internal connection. Materials and methods: For the analysis, a finite element model of implant was designed to locate at first molar area. Stress distribution was observed when vertical load of 200 N was applied at several points on the occlusal surfaces of the implants, including center, points 1.5 mm, 3.0 mm away from center and oblique load of 200 N was applied $30^{\circ}$ inclined to the implant axis. The finite element model was analyzed by using of 3G. Author (PlassoTech, California, USA). Results: The DAS tech implant (internal step with no taper) showed more favorable stress distribution than other internally connected implants. AS compare to the situations when the loading was applied within the boundary of implants and an oblique loading was applied, it showed higher equivalent stress and equivalent elastic strain when the loading was applied beyond the boundary of implants. Regardless of loading condition, the abutments showed higher equivalent stress and equivalent elastic strain than the fixtures. Conclusion: When the occlusal contact is afforded, the distribution of stress varies depending on the design of connection area and the location of loading. More favorable stress distribution is expected when the contact load was applied within the diameter of fixtures and the DAS tech implant (internal step with no tapering) has more benefits than the other design of internally connected implants.