• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.460-470
• /
• 2015

In general ships and FPSOs, roll damping is very small and consequently roll motion is very large at the roll resonance frequency. Proper evaluation of the roll damping coefficient at the resonance frequency is an important task in the study of roll motion and usually it is done by the analysis of free roll decay tests. The relative decrement method based on energy relation has been used mainly for the evaluation of roll damping coefficient from the roll decay test so far. As another method, the logarithmic decrement method based on equivalent linear decay assumption can be used for the same purpose and it is relatively simple. In this paper, both of the relative decrement method and the logarithmic decrement method are used for the evaluation of roll damping coefficient including quadratic damping from the free roll decay tests, and their results are cross-checked for verifying the obtained damping coefficients. Through applications to a box-type floating body equiped with bilge keels, it is shown that the two methods give almost the same damping coefficients in a practical view point and the cross-check of their results is to be a good tool to prevent a possible error. And also the quantitative effects of the bilge keels on the roll damping of box-type floating body are shown and discussed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.5
• /
• pp.15-23
• /
• 2010

To reduce the vibration levels, additional dissipation elements such as dry friction dampers are sometimes integrated into bladed disk assembly. In this study, forced response analysis systems for a tuned bladed disk with friction dampers were developed and verified. For the efficient nonlinear vibration analysis, multi-harmonic balanced method and cyclic boundary condition were used. Also, mode shapes obtained using fictitious mass method were used to describe the motion of the structures with the concentrated structural nonlinearity, friction damper. The relative convergence of fictitious mass and traditional unconstrained modes were compared.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.85-86
• /
• 2009

A nondestructive test method based on the self-compensating frequency response function is proposed in this paper to quantitatively measure the attenuation in concrete materials. Since the proposed technique measures inherent attenuation of material itself, more stable experimental results can be expected. In advance, comparison of the experimental results to those obtained by other methods shows the repeatability and accuracy of the proposed technique.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.199-205
• /
• 2012

In this study, wave transformation by damping due to the permeable bed of finite depth is investigated. The relationship between wave damping rate and relative water depth are presented. The damping rate is used in the eigenfunction expansion method to calculate the wave dissipation over the permeable bed. For a permeable shoal, the eigenfunction expansion model result is compared with that of the integral equation method to show good agreement. The model is also used to examine the wave reflection over the permeable planar slope of various frequency. It has been found that in general relatively short waves are more influenced by the permeability of the permeable seabed than relatively long waves unless the water depth is so large that the influence of permeable bed on surface water waves disappears.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.2
• /
• pp.162-170
• /
• 1984

대부분의 동적댐퍼들은 주구조물의 진동진폭을 정해진 주파수 변위내에서 최대로 줄이는 것을 목 표로 한다. 그러나 공작기계의 안정성은 시편과 공구사이의 상대변위와 절삭력에 의해 결정되는 전달함수의 최대크기에 의해서보다는 실수부분의 최소치에 의해 결정된다는 것이 잘 알려져 있 다. 본 논문에서는 이 사실에 착안하여 공작기계에서 발생하는 채터를 흡수하기 위한 최적의 댐 퍼를 설계하는 절차를 제시하고 1 자유도로 대표될 수 있는 구조물의 경우에 대하여 구체적인 방 법을 예시하였다. 종래의 최적 댐퍼의 성질을 구하는 방법에 비해 수학적인 절차가 약간 복잡해 지기는 하나 전산기를 이용하여 큰 어려움이 없이 최적의 설계자료를 얻을 수 있다. 댐퍼 질량이 정해졌을 때 감쇠율과 스프링 계수를 변수로 하는 목표함수가 하나의 식으로 유도될 수 없기 때 문 에 간단한 최적화 방법으로 이변수 황금분할법을 사용하였다. 수치적인 예를 통하여 종래의 다른 방법에 의한 결과와 비교하고 제안된 방법론의 타당성을 입증하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.581-586
• /
• 1998

We investigated the effect of mechanical back side damage in Czochralski grown silicon wafer. The intensity of mechanical damage was evaluated by minority carrier recombination lifetime by laser excitation/microwave reflection photoconductivity decay method, degree of X-ray diffuse scattering, X-ray section topography, and wet oxidation/preferential etching methods. The data indicate that the higher the mechanical damage intensity, the lower the minority carrier lifetime, and the magnitude of diffuse scattering and X-ray excess intensity increased proportionally, and it was at Grade 1:Grade 2:Grade 3=1:7:18.4 that the normalized relative quantization ratio of excess intensity in damaged wafer was calculated, which are normalized to the excess intensity from sample Grade 1.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.1
• /
• pp.35-44
• /
• 2006

In general typically granular soils contain a certain amount of fines. It is also widely recognized that foundation soils under working loads show highly non-linear behavior from very early stages of loading. In the present study, a series of laboratory tests with sands of different silt contents are conducted and methods to assess strength and stiffiness characteristics are proposed. Modified hyperbolic stress-strain model is used to analyze non-linearity of silty sands in terms of non-linear Degradation parameters f and g as a function of silt contents and Relative density Dr. Stress-strain curves were obtained from a series of triaxial tests on sands containing different amounts of silt. Initial shear modulus, which is used to normalize Degradation modulus of silty sands, was determined from resonant column test results. From the laboratory test results, it was observed that, as the Relative density increases, values of f decrease and those of g increase. In addition, it was found that values of f and g increase and decrease respectively as a Skeleton void ratio $(e_{sk})$ increases.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.117-123
• /
• 1998

We investigated the effect of mechanical backside damage in Czochralski grown silicon wafer. The intensity of mechanical damage was evaluated by minority carrier recombination lifetime by laser excitation/microwave reflection photoconductivity decay method, photo-acoustic displacement method, X-ray section topography, and wet oxidation/preferential etching methods. The data indicate that the higher the mechanical damage intensity, the lower the minority carrier lifetime, and the photo-acoustic displacement values increased proportionally, and it was at Grade 1: Grade 2:Grade 3 = 1:19.6:41 that the normalized relative quantization ratio of excess photo-acoustic displacement in damaged wafer was calculated, which are normalized to the excess PAD from sample Grade 1.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.29-29
• /
• 2011

국내에서 기존건축물의 내진성능평가 기법이 연구되기 시작한지 20여 년간 다양한 평가방법이 제안되었다. 그러나, 제안된 평가방법은 미국이나 일본의 평가 방법을 도입 및 수정하는 내용이 주가 되어 국내실정에 맞지 않는 부분도 많이 발견되었다. 따라서 국내에서 제안된 기존 건축물의 내진성능 평가기법, 지진피해예측에 근거한 보강건축물의 합리적인 선정방법 및 이들 건축물에 적합한 내진보강방법 등의 연구는 아직까지 초보적인 단계라고 할 수 있다. 이에 본 연구의 목적은 이러한 평가 기법을 적용한 국내 저층구조물의 내진성능을 평가하는 것이다. 저층구조물의 내진성능을 평가하기 위하여 1988년 내진설계가 도입되기 이전에 건립된 4층 규모의 학교구조물을 해석대상 구조물로 선정하였다. 대상 해석구조물의 내진성능평가는 일본의 내진성능 평가법을 참고하여 평가절차가 다소 복잡한 부분을 국내 실정에 맞게 개선시킨 내진화 우선도 평가방법과 정밀한 내진성능을 평하는 방법으로 세계적으로 널리 사용되고 있는 ATC-40 성능평가방법에서 등가단자유 모델로 변환 과정에서 등가유효감쇠 및 등가유효주기 산정 관계식의 문제점을 개선한 FEMA-440의 선형화 성능평가방법(Linearization Method)을 사용하여 구조물의 성능을 평가하였다. 내진 성능 평가를 위해 현재 전 세계적으로 널리 사용되고 있는 구조물 비선형 전용 해석 프로그램인 Perform-3D를 이용하여 해석을 수행하였다. 본 연구를 통해 기존 저층구조물로 선정한 학교구조물에 대한 내진성능을 평가한 결과, 내진화 우선도 평가법 및 FEMA-440의 내진성능 평가는 유사한 경향의 결과를 나타내었고, 두 평가결과를 요약하면 Y방향은 보와 기둥에 끼인 조적벽체의 영향으로 별도의 내진성능이 향상 보강이 필요없으나, X방향은 창문하부 허리 조적벽 등의 영향으로 다소 취성적인 내진성능을 보유하고 있어 충분한 내진성능 확보를 위한 추가적인 보강이 필요한 것으로 판단된다.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.7
• /
• pp.29-38
• /
• 2018

Three-dimensional continuum modeling of dynamic soil-pile-structure interaction embedded in a liquefiable sand was carried out. Finn model which can model liquefaction behavior using effective stress method was adopted to simulate development of pore water pressure according to shear deformation of soil directly in real time. Finn model was incorporated into Non-linear elastic, Mohr-Coulomb plastic model. Calibration of proposed modeling method was performed by comparing the results with those of the centrifuge tests performed by Wilson (1998). Excess pore pressure ratio, pile bending moment, pile head displacement-time history according to depth calculated by numerical analysis agreed reasonably well with the test results. Validation of the proposed modeling method was later performed using another test case, and good agreement between the computed and measured values was observed.