• Analytical Science and Technology
• /
• v.6 no.1
• /
• pp.65-75
• /
• 1993

A number of alternative cleaning solvents to CFC 113 which was identified as a ozone-depleting meterial were collected to measure their experimental physecal properties of density, surface tension, Refractive Index, boiling point, pH, viscosity, flash point, and soltbility. They might be classified as aqueous, simi-aqeous, alcohol ketone, and halogen cleaning solvents. The solubilities of abietic acid, a major component of flux used in PCB (Printed Circuit Board) of the electronic indystry, into the cleaning solvents including CFC 113 were determined for comparison. The assorted cleaning solvents have their own advantages and disadvantages. Therefore a end-user carefully needs to choose the best-fit cleaning solvent after the safety, stability, and economics as well as the effectiveness by physical properties of the alternative cleaning solvents are integratedly considered.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.133-140
• /
• 2013

Carbon fiber reinforced polymer (CFRP) composites consist of carbon fibers in a polymer matrix. Recently, CFRP composites having high thermal stability and low outgassing are finding their use in high performance materials for aerospace and electronics applications under high temperature and high vacuum conditions. Cyanate ester resin is one of the most suitable matrix resins for this purpose. In this study, proper combination of cyanate ester and catalyst, curing behavior, and cure cycle were determined by chemorheology. Optimum condition was found to be catalyst content of 100 ppm and curing temperature of $150^{\circ}C$. Thermal stability and outgassing of cured resin composition were analyzed and the results showed thermal decomposition temperature of $385^{\circ}C$ and total mass loss of 0.29%. The CFRP prepregs and subsequent composites were fabricated by predetermined resin composition and the cure condition. Tensile moduli of the composites were compared with theoretical models and the results were very consistent.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.396-405
• /
• 2009

An interlocking equipment of railway signalling systems should have very high functional safety and reliability properties because of its vital railway protection functionality. In order to achieve the required safety and reliability level, an engineer, in general, designs and implements the interlocking equipment to operate under RTOS(Realtime Operating System) environment, and the control hardware architecture redundant to cope with the random failures of system or subsystem. In such an architecture, it's very difficult to implement the interlocking equipment to communicate with various interface systems including the signal operator's terminal. In this paper, we propose a dual ethernet network topology and dual packet seamless transfer protocol algorithm for railway signaling system such as the interlocking equipment. We verify in this paper that the proposed DPST protocol algorithm has the evidence of its robust properties against the random hardware faults and communication errors. The proposed communication structure and algorithm is implemented in the electronic interlocking equipment for the private railway system of Hyundai Steel Company and its performance and properties are validated on the guideline of European Railway Standard EN50159.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.57.1-57.1
• /
• 2009

나노이산화티타늄은 인체에는 화장품, 의약, 식품분야 등에 쓰이고 외부 환경 재료에는 광촉매로서 유독가스 정화제, 옥내 외 항균, 수소발생 가시광 응답형 촉매 및 멤브레인 필터 등과 전자소재용 유전재료, 발광 재료 등 용도가 다양하다. 나노 산화티타늄 화합물의 제조법은 수열합성법, 기상법 등 여러 방법이 있다. 이들에 대한 리뷰의 목적은 2009년도 정부의 투자 계획 중에서 본제목에 관련되는 핵심 산업 재원 원천기술 개발, 태양광, 풍력 등의 신재생 에너지 개발, 록색 기술 개발을 통한 에너지절약형 LED 개발, 차세대 핵심환경 기술 개발, 핵심나노기반기술개발 등의 개발을 위하여 4,363억 원의 예산을 편성하고 연구자와 기술자들이 참여하여 유익한 실적이 창출되기를 원하고 있으므로 본 발표자들은 이 분야에서 연구하는 연구자와 기술자들에게 이 분야에 관련되는 자료를 참고로 제시하는데 있다. 페로브스카이트형 산화물인 유전재료($BaTiO_3$), 발광재료(CaTiO3:Pr3+적색), 박막형 반응기재료($Ca0.8Sr0.2TiO_3$), 등의 여러 가지 산화물은 류통식 급속 승온 수열 합성법, 겔 졸 법, 수열 합성법 등 여러 방법에 의하여 페로브스카이트형 산화물 입자 직경이 약 20nm~100nm 범위까지 합성된다. 태양광을 조사하여 물을분해 해서 수소를 생산하는 산화티타늄계 가시광 응답형 Vis-$TiO_2$ 박막은 기상법으로 제조하는데 한 예로써 RF 스퍼터링법으로 박막을 제조하여 수소와 산소를 회수하였으며, 황도프산화티타늄, 질소 도프 산화티타늄은 유기물 분해에 의한 공해제거, $NO_x$ 제거 등 환경정화에 사용되고, 고온 고압수법/산화티타늄 복합기술에 의해서는 바이오매스 분해 하고, 일종의 수열법인 개량형 HyCOM 법은 가시광 응답성 산화티타늄을 합성하여 NO가스 제거에 사용한다. 이들 여러 방법에 관한 것을 소개하고저 한다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.453-458
• /
• 2016

One of the most common applications of machine vision is quality inspections in automated production. In this study, a welding inspection system that is controlled by a PC and a PLC equipped with a multi-camera setup was developed. The system was designed to measure the primary dimensions, such as the length and width of the welding areas. The TCP/IP protocols and multi-threading techniques were used for parallel control of the optical components and physical distribution. A coaxial light was used to maintain uniform lighting conditions and enhance the image quality of the weld areas. The core image processing system was established through a combination of various algorithms from the OpenCV library. The proposed vision inspection system was fully validated for an actual weld production line and was shown to satisfy the functional and performance requirements.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.181-187
• /
• 2016

Silica is an essential material in the electronics industries of LCDs and OLEDs, which particularly require high purity. This study attempted to find the optimal design of a magnetic separator for silica sand containing iron compounds using CFD simulation. Three designs of magnetic separation were prepared and their efficiency was examined. As a result of the evaluation, the sufficient contact of particulate silica with the surface of magnetic emitters improved the magnetic separation effects. In addition, the loss of $SiO_2$ and the removal rate of $Fe_2O_3$ depended strongly on the particle size, flow rate and magnetic flux density. In addition, magnetic separation is quite effective for a particle size of $10{\mu}m$ with a 0.2 m/s flow rate.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.57-65
• /
• 2010

Recently, we have investigated the recovery of resources from the waste material of manufacturing printed circuit board. As printed circuit board or chip has become light, small, high reliability, it is necessary to reuse and recover resources from them. Especially, the printed circuit board that has been used for important mobile electronic pans are plated with min.0.03 ${\mu}m$ to max.50 ${\mu}m$. As increasing the cost of gold, raw material, chemicals, payments and waste material, it has been accelerated the competition for reuse and recovery. But, it is insufficiency of technician and equipments for the recovery of effective resource. In this paper, as analyzing the technical trend of gold recovery and waste back board from the manufacturing process of printed circuit board, it may be effective of recycling, further more it may be contributed to develop the valuable resources.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.414-416
• /
• 2003

As environmental conditions for memory products are increasingly high speed/high density, adopting diverse system configuration, it's more and more difficult for current component tester to adopt the actual condition of field application. If system test screening is realized in component level, test coverage failure can be made more secured in the initial stage, evaluation cost can be reduced and the effectiveness of investment for the facility can be maximized. Based on the above background, component automatic system tester was developed and showed off satisfactory results per each memory device family. In this paper, component quality stabilization strategy and cost saving for tester investment through future Quality monitoring and application to mass production will be presented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2587-2593
• /
• 2014

Ceramic Injection Molding (CIM) is one of wide used processes in industry field and the applications are gradually being expanded to parts of medical and electric devices. In this study, the CIM process were analyzed with FEM and process parameters were studied and analyzed the effect on product quality. The shape of simple flat plate was compared to the shapes with the hole, with the round corner portion or with the side wall portion. If there are holes then the hole around the uneven density distribution and the defects such as weld lines could be occurred. The Large radius of the corners of the product give good formability and fluidity. Not only the shape parameters of product but also the process parameters during CIM are studied. The simulation results showed that the process parameters of temperature, initial fractions and velocity are important design parameters to improve the quality of products.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.4
• /
• pp.808-814
• /
• 2007

In this paper, the measurement system of crane moving range is concerned with range recognition technology using phase and magnitude of radio wave. By the proposed technology, we design the radio transmitter and receiver and realize the measurement system, and save the data in disk that is earned from 900Mhz RF signal, middle frequency 450khz of analog signal. As a result of RF measurement, we got 9.3 dBm of RF output and 96 dBc@10khz of phase noise. Range information is earned the data through digital signal processing of IF signal. For the estimation of range measured, we analyze the difference between real range and measurement range, and also suggest the method to remove the measurement error using average processing and amplitude properties. A result is 0.12 and 0.00422 deviation in l0mn-30m and within 5m respectively, and then 2.4E-04 deviation in 4m by using compensation of level characteristics lately.