$Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ oxide was synthesized by polymerized complex method. Dense membrane of perovskite oxide was prepared using as-prepared powder by pressing and sintering at $1080^{\circ}C$. Leakage test was conducted on the membrane sealed by gold ring, Pyrex ring or Pyrex powder as a sealing material. The oxygen permeation flux of $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ membrane increased with increasing temperature and was $0.74mL/min{\cdot}cm^2$ at $900^{\circ}C$. In the case of the membrane applied by sealing material, oxygen permeation flux of the membrane using gold ring at $950^{\circ}C$ was higher than that using Pyrex materials because the undesired spreading of Pyrex glass materials in the membrane led to the reduction of effective permeation area. Microphotograph analysis results for the membrane after permeation test confirmedthe diffusion of Pyrex glass seal into the membrane.
$La_{0.6}Sr_{0.4}Ti_{0.3}Fe_{0.7}O_{3-{\delta}}$(LSTF) coated $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$(BSCF) membranes which has properties of high oxygen permeability and stability to $CO_2$ were applied to a bench scale apparatus to conduct oxygen permeation experiments. Also, the membranes of the laboratory and the bench scale device were divided into three regions according to the temperature gradient in the membrane reactor for comparative analysis. While oxygen permeation experiment were conducted up to $900^{\circ}C$, temperature dependence of Cr deposition was investigated. As a result, it was confirmed that the oxygen permeability was $2.37ml/min{\cdot}cm^2$, which was significantly lower than $3.79ml/min{\cdot}cm^2$ measured in the laboratory apparatus. It was found through XRD and SEM/EDS analysis that the decrease in oxygen permeability was originated from the deposition of gaseous Cr on the membrane surface released from the alloy material of the housing. In particular, a large amount of Cr was found in the medium temperature region.
The gas separation performance of a mixed membrane structure based on a mixture of polyethersulfone (PES) and cobalt tetraphenylporphyrin-benzylimidazole (CoTpp-BIm) as an oxygen carrier was investigated. The CoTpp-BIm mixed PES membrane had an asymmetric structure with a mixture of finger structure and sponge-like structure, and the upper surface was dense. The gas separation performance test was carried out using $94%\;N_2$ gas and $6%\;O_2$ mixed gas. Oxygen and nitrogen permeability coefficients were measured at ${\Delta}P$ ranging from 15 to 228 cmHg and the permeate side of the PES membrane was maintained at vacuum level. The oxygen permeability coefficient of CoTpp-BIm mixed PES membranes increased as supplied pressure was decreased. When the supply pressure was 15 cmHg, the gas permeability ($P_{O_2}$) was 6676 Barrer, the $O_2/N_2$ selectivity (${\alpha}$) was 6.1, and the promoting factor (F) was 2.39. Based on these results, it was confirmed that the addition of CoTpp-BIm to the PES film improved the oxygen separation characteristics.
Proceedings of the Membrane Society of Korea Conference
/
1997.10a
/
pp.51-52
/
1997
1. 서론 : 폴리이미드는 우수한 기계적 강도와 열적, 화학적 안정성으로 인해 최근 막분리 재료로 많이 연구 검토되고 있다. 대부분의 폴리이미드는 비교적 높은 선택도를 가지고 있으나 투과계수가 떨어지는 단점을 지니고 있어소 이를 극복하기 위한 많은 연구가 진행되어 왔다. 그 결과 투과계수를 크게 증가시킨 폴리이미드를 함성하였으나 선택도는 감소하여 투과특성의 상위한계를 넘지는 못하였다. 이 한계를 극복하기 의해서 복합잴를 이용하거나 UV, 플라즈마 처리에 의한 고분자막의 수식 등 많은 방법들이 연구되고 있다. 본 연구는 NaX형 제올라이트를 폴리이미드에 혼화시킨 막으로 산소/질소의 분리투과특성의 개선을 시도하였으며, NaX형 제올라이트와 폴리이미드 혼화방법, 혼화비율 등이 기체투과특성에 미치는 영향을 고찰하였다. 본 실험에 사용된 NaX형 제올라이트는 직접 합성하여 사용하였다. 폴리이미드는 2,3,5,6-Tetramethyl-1,4-phenylenediamine(p-TeMPD)과 (3,3,4,4'-dicarboxyphenyl)-hexafluoropropene-dianhydride(6FDA)로 합성한 6FDA-p-TeMPD 폴리이미드를 사용하였고, 그 투과계수는 122Barrer, 선택도$\alpha$$_{N_2/O_2}$ = 3.4이다.
Proceedings of the Membrane Society of Korea Conference
/
1994.10a
/
pp.28-29
/
1994
일반적으로 polyimide는 열적, 화학적으로 안정하며 좋은 기계적 성질을 갖고 있고 기체투과 특성이 뛰어나므로 훌륭한 막 소재로 알려져 있다. 그러나, 높은 선택도를 나타내면 투과도가 떨어지고 투과도가 높으면 선택도가 떨어지는 일반적인 고분자 막이 보이는 경향을 따르므로, 본 연구에서는 이례적으로 높은 산소 투과도를 보이는 6FDA-pTeMPD polyimide와 높은 선택도를 나타내는 6FDA-mPDA polyimide을 공중합 시킴으로써 각각의 homopolyimide로서는 얻을수 없는 개선된 기체 투과도와 선택도를 얻을 수 있으리라 예상하여 연구를 하였다. 조성과 자유용적, 조성과 Tg관계, 조성과 투과도 및 선택도를 조사하여 공중합 하였을때 고분자의 화학 구조와 미시적 구조간의 관계를 규명하여 분자 설계로 적절한 막 특성을 갖는 공중합 막을 합성할 수 있는 정보를 확립하였다.
Park, Min-U;Yeo, Dong-Hyeon;Won, Beom-Hui;Lee, Ji-Hye;Lee, Chae-Min;Ha, Myeong-Hun;Jeong, Dong-Geun
Proceedings of the Korean Vacuum Society Conference
/
2013.02a
/
pp.443-443
/
2013
유기광전자소자는 아주 얇은 두께로 제작 가능하여 휘어지는 소자를 구현할 수 있다. 이런 장점 때문에 플렉서블 디스플레이, 플렉서블 태양전지 구현에 가장 적합한 소자로 각광받고 있다. 하지만 수분이나 산소에 의한 소자내의 유기물과 금속의 열화로 소자의 수명이 줄어들기 때문에 산소 및 수분 침투를 방지하는 봉지기술(encapsulation)이 필요하다. 본 연구는 원자층 증착법을 이용한 무기박막층과 분자층 증착법을 이용한 폴리머박막의 적층구조를 이용하여 유기소자에 적용할 수 있는 수분 투과 방지막을 제작하였다. 무기박막층으로는 trymethylaluminum (TMA)과 $H_2O$를 사용하여 $Al_2O_3$를 제작하였고 폴리머층으로는 TMA와 ethylene glycol를 사용하여 alucone박막을 제작하였다. 폴리머층으로 사용된 alucone박막의 X-선 광전자 분광 스펙트럼은 대기중 수분과 산소에 의한 화학결합구조의 변화를 보였지만, $Al_2O_3$와 적층구조로 사용되었을 때, 배리어특성을 증가시키고 휘어짐에 따른 보호막의 열화현상을 줄여줄 수 있는 것을 Ca-test를 통해 확인하였다. 이러한 현상은 alucone막을 적층함으로써 $Al_2O_3$를 침투한 소량의 수분과 산소가, alucone박막을 지나면서 다음 $Al_2O_3$ 층으로 침투하기 전까지의 경로를 늘려주기 때문이라 사료된다.
고주파 마그네트론 반응성 스퍼터링(rf magnetron reactive sputtering)으로 티타늄산화물 박막을 제조하여 산소비율에 따른 반응성 스퍼터링의 증착기구를 조사하고 산소비율 및 기판온도에 따른 산화물 조성의 변화, 미세조직, 광학적 특성의 변화를 연구하였다. 기존의 진공기상증착법으로 증착만 박막에 비해, 금속타겟을 사용하여 높은 증착속도를 얻을 수 있는 반응성 마그네트론 스퍼터링으로 성막한 티타늄산화물 박막은 치밀도가 우수하여 높은 굴절률(2.06)과 높은 광투과율을 보였다. 상온에서 성막된 티타늄 산화물박막의 경우, 산소비율이 낮은 조건에서는 다결정형의조직을 보였으나 산소비율이 높은 경우에는 비정질조직을 나타냈으며, 기판온도가 30$0^{\circ}C$ 이상에서는 산소비율에 상관없이 다결정형의 조직을 나타냈다. 하지만 산소비율이 임계값이상에서는 박막의 조성, 증착속도 등이 거의 변하지 않는 안정된 증착조건을 보였다. 30% 이상의 산소비율의 반응성 스퍼터링의 조건에서는 TiO$_{2}$의 조성의 박막으로 성장하여 약 3.82-3.87 eV의 band gap을 나타냈으며 기판온도의 증가에 따라 비정질 TiO$_{2}$에서 다결정 TiO$_{2}$으로 조직의 변화를 보여 광투과도도 약간 증가하는 경향을 나타냈다.
The true-lPN's based on silicone rubber(SR)rrubbery polymer) and polystyrenc(PS)(glass polymer) were prepared by using the sequential IP!\' method_ The characteristic of permeability of oxygen/nitrogen was investigated with the control of the amount of PSOO-70 wt%) in the true-lPN, As a results of fTlR and N1Vm. the SRIPS membrane was synthesised successfully with the IPN synthetic method, Thermal analysis resulls indicated that the degree of mixing of IPN increased with increase of the amount of PS in the IPN. Regarding the characteristic of gas permeability, the membrane showed a trend of decrease in oxygen permeability as the PS content increased, The oxygen permeability of membrane having 50 wt% of PS. however, increased momentarily, Selectivity, meanwhile, increased slightly as the contents of I'S increased. However, the maximum value of oxygen selectivity, which is 20.6% enhanced Value, was obtained with the membrane containing 50 wt% of PS. This can be explained that the behavior of lPN, i.e. mutual assistance, is pronounced in the membrane having 50 wt% of PS.
To investigate the performance of VOC separation, composite hollow fiber membrane was prepared which composed of poly (ether imide) support prepared by phase separation method and poly (dimethylsiloxane) coating active layer. The performances of the membranes for the application of recovery process in terms of their morphology, gas permeance test for $N_2$ and $O_2$ gases. Durability against benzene, toluene and xylene was also investigated. And permeation test for multi-component VOCS through the membrane with different feed concentration and stage-cut were investigated. Permeance of PEI supported membrane and the membranes coated with PDMS decreased from 45,000 GPU to 63 GPU and 49,450 to 30 GPU for $N_2$ and $O_2$, respectively. Recovery efficiency and concentration of VOCs in permeate increased with decreasing stage-cut. VOCs concentration in permeate proportionally increased with increasing feed concentration but concentration ratio and recovery efficiency showed any noticeable changes with feed concentration change.
Proceedings of the Korean Vacuum Society Conference
/
2012.02a
/
pp.169-169
/
2012
현재 디스플레이 시장은 LCD (Liquid Crystal Display), PDP (Plasma Display Panel) 등과 같이 평판 디스플레이가 주류를 이루고 있으며 현재에는 기존의 디스플레이와는 달리 잘 휘어지고 높은 투과성을 가지는 플렉시블 디스플레이에 대한 연구가 활발히 진행 중이다. 하지만 이러한 플렉시블 디스플레이에 사용되는 플라스틱 기판의 경우 용제에 대한 화학적 저항성 및 기계적인 안정성이 취약한 점과 대기중의 수분이나 산소가 플라스틱 기판을 통하여 소자내로 침투하게 되어 금속전극을 산화시키거나 기포 또는 흑점 등과 같은 비 발광 영역이 확산되어 소자의 수명을 단축시키는 치명적인 단점을 가진다. 이에 본 실험에서는 고밀도 플라즈마 형성이 가능하고 저온공정이 가능한 FTS (Facing Target Sputtering) 장비를 이용하여 Polyethylene terephthalate (PET) 기판위에 낮은 수분 투과율 또는 산소 투과율을 갖는 양질의 무기 산화막을 적층하기 위해 저 투습도 및 기계적인 경도 향상을 위한 비 반응성 박막으로 $Al_20_3$층을 Ar분위기에서 증착하였고 그 위에 박막의 stress 감소, 유연성 향상을 위한 반응성 박막으로 Al을 Ar과 $O_2$를 비율별로 증착하여 비교 실험하였다. 이와 같이 제작된 무기산화막들을 Uv- spectrophotometer를 이용하여 광학적 특성을 조사한 결과 가시광 영역에서 모두 80% 이상의 높은 투과율을 나타내었으며, 그 외 XRD (X-ray Diffraction)를 사용하여 결정성을 확인, SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope)을 이용하여 박막의 구조와 표면향상 및 표면조도를 측정한 결과 모든 박막에서 밀집도가 좋으며 거칠기가 작은 것으로 확인되었다. 마지막으로 수분 투과율(WVTR)을 알아보기 위해 Mocon (Permatran W3/31)장비를 이용하여 측정한 결과 $1.0{\sim}3.0{\times}10^{-3}g/m{\cdot}day$의 낮은 수분 투과율을 볼 수 있었다. 이러한 측정 결과로 볼 때 향후 FTS 장비를 이용하여 양질의 플라즈마를 형성하여 알루미늄 무기산화막을 이용한 고밀도 다층막을 형성하면 더욱 낮은 수분투과율을 갖는 가스차단막을 제작할 수 있을 것으로 보여지며 반도체 소자 및 디바이스의 Pachaging으로도 사용가능 할 것이라 사료된다. 본 연구는 한국산업기술진흥원에서 지원하는 2011년도 지역산업기술개발사업의 연구수행으로 인한 결과물임을 밝힙니다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.