• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.375-376
• /
• 2006

Thermoplastic elastomer(TPE) can be molded by conventional injection molding. Therefore TPE injection molding could be analyzed by commercial flow analysis software. However there are a little of gaps on CAE simulation results and practical molding. In this study, the properties of TPE were measured and applied to CAE simulation for comparing the simulation flow pattern and real flow pattern. The pattern that was controlled by injection time was match. The pattern that was controlled by injection stroke and rate was not match.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.48-59
• /
• 2017

In this study, an analysis of the thermo-fluid dynamic and missile-motion performance was carried out through a numerical simulation inside the missile canister. Calculation was made in an analytical volume using dynamic grid and evaporated water was used as a coolant. To analyze the interaction among the hot gas, coolant, and mixture flow, Realizable $k-{\varepsilon}$ turbulence and VOF (Volume Of Fluid) model were chosen and a parametric study was performed with the change of coolant flow rate. As a result of the analysis, pressure of the canister showed a large difference depending on the presence or absence of the coolant, and also showed a dependancy on the amount of coolant. Velocity and acceleration were dependent on the canister pressure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.1
• /
• pp.1-4
• /
• 2002

A short shot is a molded part that is incomplete because insufficient material was injected into the mold. Any factors that increase the resistance of polymer melt to flow or prohibit delivery of sufficient material into the cavity can cause a short shot. Inappropriate injection pressure is one of the most common factors which cause a short shot. Conventionally, domain experts in injection molding decide and modify the pressure based on their experience. It is difficult for a non-expert to decide the pressure properly with the considerations such as a part dimension, shape, and other processing variables. In this study, fuzzy algorithm is proposed to standardize the empirical determination of the pressure so that not only the experts but also non-experts can find the appropriate injection pressure easily. To acquire the more accurate results. domain experts should be interviewed and then technical documents which are collected from the experts should be restored in the fuzzy rule base. But in this study, simulations have been done by using C-MOLD to settle the rule base because it takes much time and also it's difficult to meet and interview the experts.

• The Korean Journal of Rheology
• /
• v.11 no.2
• /
• pp.159-167
• /
• 1999

Sandwich injection molding is one of the remarkable polymer processes recently developed from conventional injection molding. But it is almost impossible to do theoretical investigation that we've researched it through numerical simulation. In this paper, numerical simulation on the study of sandwich injection molding is based on Finite Element Method and FAN/Control Volume method. In addition to conventional filling parameter that can confirm skin polymer melt front, new filling parameters have been introduced to confirm core polymer melt front advancement. These filling parameters are defined in each layer which is divided to solve temperature field along the thickness direction. One can notice different filling patterns resulted from the variation of material properties such as viscosities and power-law indexes, and processing conditions such as switch-over times and wall temperatures. It gives us a better understanding of the sandwich injection molding process. And we can recognize that it's the core polymer spatial distribution after the completion of filling that is the most important key point to use this process for industrial molding process.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.4
• /
• pp.1-8
• /
• 2011

Injection molding machine is the assembly of many kinds of mechanical and fluid power part and electro-electronic control system. From in these, fluid power is a part where becomes the first core of this machine. Fluid power systems of injection molding machine are modelled and analyzed using a commercial program AMESim. The analysis model which is detailed about the parts applied a publishing catalog data. Sub system models which is divided according to functional operation are made and its analysis results shows how design parameters work on operational characteristics like displacement, pressure, flow rates at each node and so on. Total fluid power circuit model is also made and analyzed. The results made by analysis will be used design of fluid power circuit of injection molding machine.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.230-233
• /
• 2006

In this study, the effects of residual stress induced by plastic injection molding process on the tensile behavior of plastic tensile test specimen were investigated. To manufacture plastic tensile test specimens, an injection mold based on the international standard system was designed and made. Cavity pressure and temperature sensors were installed inside of the presented mold to monitor pressure and temperature values during the cycle of injection molding. Injection molding simulation was performed with the same condition of experiment and linear structural tensile analysis was also performed with the initial condition of the residual stress. It was shown that the residual stress induced by injection molding has an effect on the experiment of tensile test and linear structural tensile simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.784-787
• /
• 2003

The present work covers three-dimensional flow simulation and deformation analysis of injection molded plastic lenses using solid elements. A numerical scheme to evaluate part deformation has been proposed from the results of injection molding analysis. Proposed scheme has been applied to the injection molding processes of optical plastic lenses: a spherical lens and an aspheric lens for a photo pick-up device. Through the simulation processes. residual stress is estimated and the final deformed patters are obtained for both products. The reliability of the proposed approach has also been verified in comparison with the results of real experiments.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.64-72
• /
• 2001

Weld line is one of serious troubles which are observed in a plastic part manufactured by a injection molding process. This is caused by many process factors, which are molding pressure, temperature, velocity, location of a injection gate, mold geometry and material properties. investigation on the effects of these process factors to the appearance of a weld line was carried out using a finite element method. Filling and packing analyses were carried out by modifying both the configuration of the injection gates and cavity thickness. Proper locations of the injection gates could be determined by considering molding pressure, temperature, velocity and frozen layer, and whereby the weld line was controled. In order to make a weak appearance of the weld line, flow velocity and flow front in a cavity were also investigated by modifying a cavity thickness. As a result, flow front was extended around the corner in the cavity by changing the flow velocity and hence the appearance of the weld line was much weakened.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.812-815
• /
• 2000

Injection molding process was taken to manufacture DC motor case that surrounds DC motor used as automobile parts. Up to now, DC motor case has been made by the deep drawing process or bending process of metal materials. Simulations of filling, packing and cooling processes were done by CAE tool like Moldflow software. Optimal delivery system was decided from the analysis of flow balance, and packing and cooling analyses were performed by using the design of experiment to minimize the volumetric shrinkage of molded part and the temperature difference between mold and part.