• Economic and Environmental Geology
• /
• v.50 no.2
• /
• pp.129-143
• /
• 2017

The shallow sediments in the southwestern Ulleung Basin consist of mass flow deposits such as slide/slump and debris flow deposits (DFD), caused by slope failure. These sediments are proven to be important in studying geological disaster and stability of the seafloor. In this paper, we analysised the flow accumulation and slope failure susceptibility of the Ulleung Basin on the basis of multi-beam data, collected in this area. We also studied the distribution pattern and the seismic characteristics of the DFD in the uppermost layer of the Ulleung Basin on the basis of seismic data. The slope susceptibility was calculated as the frequency ratio of each factors including slope, aspect, curvature and stream power index (SPI), which causes the slope failure. These results indicate that the slope failure is frequently to occur in the southern and western continental slope of the Ulleung Basin. The sediment flow (mass flow) caused by the slope failure converges to the north and northwest of the Ulleung Basin. According to the seismic characteristics, the uppermost layer in study area can be divided into four sedimentary unit. These sedimentary units develop from the south and southwest to the north and northwest in association with slope susceptibility and flow accumulation.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2007.06a
• /
• pp.413-423
• /
• 2007

우리나라의 자연재해는 기상학적 자연현상에 의해 주로 발생되고 있으며 그 발생원인은 태풍, 호우, 폭풍, 폭풍우, 재설, 폭풍성 우박, 해일 및 기타(낙뢰, 돌풍, 설해, 결빙, 지진 등을 포함)로 구분되며 이중 발생빈도가 가장 높은 것은 강우에 의한 재해로 전체 재해발생 원인 중 약 80%로 대부분을 차지하고 있다. 특히 사면붕괴와 관련된 자연재해(산사태, 옹벽붕괴, 매몰 등)는 최근 국지성 집중호우를 포함하여 호우의 집중 강도가 높아지는 등 기상학적 원인에 의해 매년 발생하고 있다. 따라서 우리나라에서 발생되는 자연재해와 관련한 사면붕괴의 특성을 강우특성에 따라 조사 분석할 필요가 있으며 이에 적합한 대책들이 더욱 필요하다. 이 연구에서는 산사태 유발인자와 강우조건을 고려하여 산사태 잠재가능성을 평가하고 산사태 취약지역을 분석하여 지역적인 강우특성을 고려한 산사태 가능성을 평가하였다.

• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.501-508
• /
• 2009

This study aims to clarify the characteristics of the physical and mechanical properties of soil-slope failure of Okcheon metamorphic zone. Soil samples were collected from 35 collapsed and uncollapsed artificial slopes along national roads. A series of laboratory experiments was carried out to examine physical and mechanical properties of soils and rocks. The results show that failure slopes have weakness of failure at 0.75 of AMI or higher, 32% of liquid limit or higher, and 31% of saturated moisture content or higher. The plastic index of failure slopes is correlated to wet density and saturated density. It turned out that failure could easily happen according to a high plastic index even if the void ratio was low. The greater the contents of bigger-sized soil, i.e. contents of sands and gravels rather than of clays, is the greater the chance to fail at the slope.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.545-554
• /
• 2007

Landslides is mainly induced by a heavy rainfall, earthquake ground motion, and some other factors like soil mechanics, morphological-geological factors etc. Since the starting point of the failure seemed to be originated at a construction site in the study, it is meaningful to find out the relationship between the landslide and the construction. For this study, the slope failure factor was examined carefully to see that the original natural slope had vulnerability and that the complex ground had unstability changed by construction. A field survey was conducted on the original ground surface and filled-up ground. A laboratory test was also conducted to determine the geomechanical properties of soil samples. 2D and 3D limit equilibrium analysis with changing groundwater level were conducted at the failure depth using a seismic refraction survey. The result shows that the factor of safety is similar stability under all condition, but unstable under saturated condition.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.280-280
• /
• 2017

국내의 사면안정평가는 국토교통부, 국민안전처, 산림청 등의 주요 기관에서 사면을 구성하고 있는 토양특성과 사면경사 등을 평가할 수 있는 기준을 마련하고 있다. 대부분 경우 이 기준을 가지고 자연사면의 안정성에 대한 전반적인 평가가 이루어지고 있다. 하천관리에서는 다양한 요소들을 고려하여 계획이 수립되고 실행되고 있으며 이 중 산지와 기타 지역에서 유입유사는 그 정도에 따라 하천의 통수능력 감소와 하천생태계 교란 등의 많은 영향을 미치고 있다. 이러한 이유에서 유사는 하천관리에 있어 매우 중요한 관리 대상이다. 그러나 현재 평가기준을 이용하여 사면의 붕괴 및 취약정도를 판단할 수 있으나 유역의 유사발생여부를 평가하기에는 상당한 오류를 가지게 된다. 본 연구에서는 사면평가기준을 통한 1차적인 평가와 강우로부터 발생하는 토양침식과 퇴적을 분석 결과를 적용한 종합적인 2차적인 평가를 수행하였다. (1)기존에 사용하고 있는 사면안정평가기준을 가지고 대상유역인 금호강유역의 토양특성에 대한 등급을 분류한다. (2)토층, 토지이용, 빈도별 강우자료 등 다양한 인자를 고려할 수 있는 C-SEM(Cell-based Sediment Erosion Model)을 이용하여 침식 및 퇴적 깊이를 계산한다. (3)사용하고 있는 평가기준과 침식 및 퇴적깊이에 대한 분석결과를 조합하여 금호강유역에서의 유사발생 평가를 위한 지도를 작성한다. 이 연구는 국가에서 제공하고 있는 유역관련 자료를 이용하여 대상유역에서 유사발생을 평가하고 유사발생 관련인자를 대상으로 평가기준을 제안하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.606-606
• /
• 2012

최근 지구 환경변화에 따른 기후변화의 영향으로 이상홍수 발생의 위험성이 증가하고, 상습적으로 홍수피해가 반복되고 있다. 홍수피해의 원인 중 하나인 하천제방의 붕괴는 월류, 침식, 제체불안정, 구조물에 의한 파괴 등으로 구분되고 이 중 월류 및 침식은 제방 파괴의 주된 원인으로 최근 통계자료에 보고되고 있다. 제방붕괴의 주된 원인 중 하나인 침식파괴로부터 제방을 보호하기 위해 제내지 사면에 호안공을 설치하며, 하천설계기준 해설(2009)에서는 제방 또는 하안을 유수에 의한 파괴와 침식으로부터 직접 보호하기 위해 제방 앞비탈에 설치하는 구조물로 정의하고 있다. 특히 사행하천의 만곡부에서는 제방파괴의 위험성이 높을 뿐만 아니라 국부적으로 집중되는 유속분포는 제방의 안정성을 위협한다. 또한 원심력, 2차류(secondary flow) 등에 의한 수위상승 등에 의해 제방이 파괴되고 월류되어 홍수피해가 발생할 가능성이 큰 취약지점이라고 할 수 있다. 본 연구에서는 2차원 수치모형을 이용하여 만곡부 흐름 특성을 분석하고 수리실험을 통해 측정된 유속 및 수위분포 결과와 비교하여 분석하였다. 또한 수리실험에서 도출된 호안 붕괴 시의 흐름을 구현하여 호안 붕괴 시 국부유속 및 전단응력을 계산하고 만곡부 호안의 안정성을 위한 설계인자를 분석하였다. 연구결과로 제시된 만곡부 안정성을 위한 설계인자는 국외 호안공 설계식과 비교하여 국부유속 및 전단응력의 설계인자의 적합성을 검토하고 국내 만곡부 호안의 안정성 설계기법개발에 도움이 될 수 있는 설계인자를 제시하고자 한다.

• The Journal of Engineering Geology
• /
• v.25 no.1
• /
• pp.115-129
• /
• 2015

The cut-slope of a large-sectional tunnel portal is recognized as a potential area of weakness due to unstable stress distribution and possible permanent displacement. This paper presents a case study of a slope failure and remediation for a large-scale cut-slope at a tunnel portal. Extensive rock-slope brittle failure occurred along discontinuities in the rock mass after 46 mm of rainfall, which caused instability of the upper part of the cut-slope. Based on a geological survey and face mapping, the reason for failure is believed to be the presence of thin clay fill in discontinuities in the weathered rock mass and consequent saturationinduced joint weakening. The granite-gneiss rock mass has a high content of alkali-feldspar, indicating a vulnerability to weathering. Immediately before the slope failure, a sharp increase in displacement rate was indicated by settlement-time histories, and this observation can contribute to the safety management criteria for slope stability. In this case study, emergency remediation was performed to prevent further hazard and to facilitate reconstruction, and counterweight fill and concrete filling of voids were successfully applied. For ultimate remediation, the grid anchor-blocks were used for slope stabilization, and additional rock bolts and grouting were applied inside the tunnel. Limit-equilibrium slope stability analysis and analyses of strereographic projections confirmed the instability of the original slope and the effectiveness of reinforcing methods. After the application of reinforcing measures, instrumental monitoring indicated that the slope and the tunnel remained stable. This case study is expected to serve as a valuable reference for similar engineering cases of large-sectional slope stability.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.83-92
• /
• 2018

The lapse of time may cause in the slope structure various deterioration phenomenon progresses in the ground of slope, and collapse due to deterioration of strength, resulting in a decrease in the service life. The approach to slope stability due to the ground deterioration is a different concept from the existing limit equilibrium analysis, which is limited to the physical characteristics and geometrical structure of ground. In this study, we conducted a comparative analysis of various literature studies related to the slope failure characteristics and behaviors to presented the optimal formulas for shear strength reduction, such as the exponential function, the logarithmic function and the inverse hyperbolic function. And then a case study was performed on cut slope of Gyeongbu High Speed Rail construction site along the Yangsan fault zone, where the slope failure of shale layer vulnerable to deterioration occurred. As a result, it was confirmed that landslide occurred due to reduction of shear strength by deterioration, as safety factor is approx. 1.0 at the time when the slope failure occurred. Based on the comprehensive case study, as a quantitative approach to the evaluation of slope stability due to deterioration of ground, finally we propose a method for evaluating slope stability with optimal strength reduction curves.

• Journal of Korean Society for Geospatial Information Science
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2007

Most natural disasters in Korea are caused by meteorological natural phenomena, which include storms, heavy rains, heavy snow, hail, tidal waves, and earthquakes. Rainfall is the most frequent cause of disasters and accounts for about 80% of all disasters. Particularly in recent years, Korea has seen annual occurrences of natural disasters associated with landslides (slope and retaining wall collapse and burying) due to meteorological causes from the increasing intensity of heavy rains including local heavy rainfalls. In Korea, it is critical to analyze the characteristics of landslides according to rainfall characteristics and to take necessary and proper measures for them. This study assessed the possibility of landslides in the Gangwon region with a geographic information system by taking into account the inducer factors of landslides and the maximum continuous rainfall of each area. It also analyzed areas susceptible to landslides and checked the distribution of landslide-prone areas by considering the rainfall characteristics of those areas.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.10
• /
• pp.5-14
• /
• 2017

The hazard maps for predicting collapse on natural slopes consist of a combination of topographic, hydrological, and geological factors. Topographic factors are extracted from DEM, including aspect, slope, curvature, and topographic index. Hydrological factors, such as soil drainage, stream-power index, and wetness index are most important factors for slope instability. However, most of the urban areas are located on the plains and it is difficult to apply the hazard map using the topography and hydrological factors. In order to evaluate the risk of subsidence of flat and low slope areas, soil depth and groundwater level data were collected and used as a factor for interpretation. In addition, the reliability of the hazard map was compared with the disaster history of the study area (Gangnam-gu and Yeouido district). In the disaster map of the disaster prevention agency, the urban area was mostly classified as the stable area and did not reflect the collapse history. Soil depth, drainage conditions and groundwater level obtained from boreholes were added as input data of hazard map, and disaster vulnerability increased at the location where the actual subsidence points. In the study area where damage occurred, the moderate and low grades of the vulnerability of previous hazard map were 12% and 88%, respectively. While, the improved map showed 2% high grade, moderate grade 29%, low grade 66% and very low grade 2%. These results were similar to actual damage.