• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.11-18
• /
• 2002

The structural load analysis of 50m class airship was performed. The airship maneuver condition for analysis was defined. Aerodynamic, inertia and buoyance models were built. Control surface motion to make defined maneuver condition were calculated. Load factors, load, shear and bending moment envelops were developed for full airship and tailwing. Gondola design loads were developed.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.163-173
• /
• 2018

This paper performed the prediction of the acoustic loads applied to the surface of the flight vehicle during flight. Acoustic loads during flight arise from the pressure fluctuations on the surface of body. The conventional method of predicting the acoustic loads in flight uses semi-empirical method derived from theoretical and experimental results. However, there is a limit in obtaining the flow characteristics and the boundary layer parameters of the flight vehicle which are used as the input values of the empirical equation through experiments. Therefore, in this paper, we use the hybrid method which combines the results of CFD (Computational Fluid Dynamics) with semi-empirical methods to predict the acoustic loads acting on flight vehicle during flight. For the flight vehicle with cone-cylinder-flare shape, acoustic loads were estimated for the subsonic, transonic, supersonic, and Max-q (Maximum dynamic pressure) condition flight. For the hybrid method, two kind of boundary layer edge estimation methods based on CFD results are compared and the acoustic loads prediction results were compared according to empirical equations presented by various researchers.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.7
• /
• pp.76-84
• /
• 2005

For flight loads analysis of Smart UAV, applicable regulations and loads conditions should be prepared in advance, and modeling for aerodynamics, weight, and structure should be performed. Panel method is usually adopted for aircraft loads analysis to obtain aerodynamic loads. In this study, ARGON which is a multidisciplinary fixed wing aircraft design software co-developed by KARI and TsAGI was used for loads analysis. ARGON can be utilized for flutter and stress analysis as well as for flight and ground loads analysis. In this paper, flight loads analysis of Smart UAV which is a FAR 23 category airplane was performed with ARGON and the results were presented.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2005

Civil aviation regulation such as FAR and loads analysis procedure based on this was explained, and loads analysis procedure and results for Smart UAV was presented for application case. For loads analysis, applicable regulations and loads conditions should be prepared in advance, and modeling for aerodynamics, weight, and structure should be performed. Panel method is usually adopted for aircraft loads analysis to obtain aerodynamic loads. In this study, ARGON which is multidisciplinary fixed wing aircraft design software co-developed by KARI and TsAGI was used for loads analysis. ARGON can be utilized for flutter and stress analysis as well as for flight and ground loads analysis. In this paper, flight loads analysis of 4-seater canard airplane was performed with ARGON and that results were presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.5
• /
• pp.34-40
• /
• 2005

Most analyses and researches on Micro Aerial Vehicle(MAV) have focused upon propulsion, automatic control, aerodynamic configuration in low Reynolds number region, and miniaturization of telemetric parts. In the present study, a structural concept for MAV is designed by using the composite material suitable for light flight structures. In order to study the load path and stress state of the MAV, the load and structural analyses are simultaneously performed by the aeroelasticity module of MSC/NASTRAN. The stability derivatives of the MAV are obtained for three symmetric, two antisymmetric, and four unsymmetric maneuvering conditions. Although the aerodynamic theory in MSC/NASTRAN could not be proper for MAV analysis, it provides an traditional and effective tool for trim and load analyses and may be corrected with the results by more accurate theory or test. The results show that the inertial load due to payloads has a more effect on stress rather than the aerodynamic load.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.159-164
• /
• 2016

This paper reports the load factor logic design for a fly-by-wire helicopter flight envelope protection. As a helicopter is very complex system with a rotor, fuselage, engine, etc., there are many constraints on the flight region. Because of these constraints, pilots should consider them carefully and have a heavy workload, which causes controllability degradation. In this respect, automatic logic is needed to free the pilot from these considerations. As one of these logics, the flight envelope protection logic for the load factor of a FBW helicopter was designed. The flight to exceed the load factor is caused by an abrupt pitch cyclic stick change. In this scheme, the load factor limit logic was added between the pilot stick command block and pitch attitude command block. From the current load value, the available attitude range was calculated dynamically and simulated on the helicopter simulator model to verify the performance. A comparison of the simulation results at the hovering and forward speed region with and without applying the load limiting logic showed that the load factor limit was exceeded more than 20% when the logic was not applied, whereas with the load factor limit logic the load factor was within the limit. In conclusion, a dynamically allocated limitation logic to helicopter FBW controller was verified by simulation.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.13-19
• /
• 2011

Lift off acoustic loads of KSLV-I were predicted by the modified NASA SP-8072 source distribution method (method 2) and the result was compared with those of measurements in the flight test of KSLV-I. In the second flight test, lift off acoustic loads were measured by outer microphones attached on the cable mast. The onboard data measuring outer acoustic pressure at the interstage of KSLV-I also can be obtained. The predicted result showed very similar peak and the shape of spectrum when compared with the measured spectrum and a margin about +7 dB.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.3
• /
• pp.82-87
• /
• 2004

The general requirements to achieve the structural integrity of the airframe are described in the military specification, MIL-HDBK-1530. One of these requirements is the durability and damage tolerance of the airframe, which should be shown through the analysis and test based on the related specifications. This paper describes the full scale durability test load simulation to evaluate the structural safety and durability of the advanced trainer, T-50. The test load simulation was performed according to the procedure in the military specification and the KAF contract requirements. The durability test design technique which involve the floating test set-up, the optimal test load simulation method, and the 6-DOF test article balance method to secure the real flight conditions as many as possible. It was confirmed that this method will be available in a similar full-scale airframe structural test in future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.12
• /
• pp.1184-1191
• /
• 2009

In order to reduce the download around the Smart UAV(SUAV) at Transition mode, flow control using synthetic jet has been performed. Many of the complex tilt rotor flow features are captured including the leading and trailing edge separation, and the large region of separated flow beneath the wing. Based on the results of part 1 of the present work, synthetic jet is located at 0.01c, $0.95c_{flap}$ and it is operated with the non-dimensional frequency of 0.5, 5 to control the leading edge and trailing edge separation. Consequently, download is substantially reduced compared to with no control case at transition mode using leading edge jet only. The present results show that the overall flight performance and stability of the SUAV can be remarkably improved by applying the active flow control strategy based on synthetic jet.

• Journal of Aerospace System Engineering
• /
• v.15 no.1
• /
• pp.80-85
• /
• 2021

In this study, for conducting a static load test of an external fuel tank used for an aircraft, the flight load acting on the external fuel tank was converted to the test load and the suitability of the converted test loads was confirmed. In order to calculate the test load from the flight load, the external fuel tank was divided into several sections. Shear load, moment by unit shear load, and unit moment were calculated for each section. Test loads for each section were then calculated by computing the shear load, the moment of each section, and flight load condition. In actual static load tests, it might not be possible to impose the test load in the calculated position due to physical constraints. Therefore, after determining positions in which the load could be imposed in the actual test, the test load calculated for each section was redistributed to selected positions. Finally, a test load plan was established by applying a whiffle tree to enhance the efficiency of the test performance while making it easier to operate the actuator. The reliability of the test load plan was verified by comparing it with flight load conditions.