• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.8
• /
• pp.833-842
• /
• 2011

The objectives of this research are development of guidance, navigation and control system for RUAV on virtual instrumentation and real flight test. For this research, the system is divided to DAQ (data acquisition) section, actuator section and controller section. And the hardware and software on each sections are realized on LabVIEW base. Waypoint guidance and control of auto flight are realized using PID gain tuning and waypoint vector tracking guidance algorism. For safe flight test, auto/manual switching module isolated from FCS (Flight Control System) is developed. By using the switch module, swift mode change was achieved during emergency flight case. Consequently, a meter level error of flight performance is achieved.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.7
• /
• pp.633-643
• /
• 2005

An unmanned aerial vehicle (UAV) is an aircraft controlled by .emote commands from ground station and/o. pre-programmed onboard autopilot system. A navigation system in the UAV provides a navigation data for a flight control computer(FCC). The FCC requires accurate and reliable position, velocity and attitude information for guidance and control. This paper proposes an ADGPS/INS integrated navigation system for a UAV. The proposed navigation system comprises an attitude determination GPS (ADGPS) receive., a navigation computer unit, and a low-cost commercial MEMS inertial measurement unit(IMU). The navigation algorithm contains a fault detection and isolation (FDI) function fur integrity. In order to evaluate the performance of the proposed navigation system, two flight tests were preformed using a small aircraft. The first flight test was carried out to confirm fundamental operation of the proposed navigation system and to check the effectiveness of the FDI algorithm. In the second flight test, the navigation performance and the benefit of the GPS attitude information were checked in a high dynamic environment. The flight test results show that the proposed ADGPS/INS integrated navigation system gives a reliable performance even when anomalous GPS data is provided and better navigation performance than a conventional GPS/INS integration unit.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.5
• /
• pp.490-495
• /
• 2015

As flying robots are becoming popular, there are increased needs to use themforsuch purposes as parcel delivery, serving in restaurants, and stage performances. To control flying robots such as quad copters, localization is essential. In order to properly position flying robots, many techniques are in development, including IR (infra-red)-based systemswhich catch markers on a flying robot in order that it can position itself. However, this technique demonstrates only short coverage. Furthermore, localization from inertial sensors diverges as time passes. For this reason, this paper suggests a TWR (two-way ranging) based positioning technique. Despite the weaknesses in currently available TWR system, this paper suggests a self-positioning and outlier detection technique in order to provide reliable position information with a faster update rate. The self-positioning system sends a shorter message which reduces wireless traffic. By detecting and removing outlier measurements, a positioning result with better accuracy is acquired. Finally, this paper shows that the suggesting system detects outlierssequentially from less than half the number of anchors in localization system according to the degree of outlier in measurement and the noise level. By performing an outlier algorithm, better positioning accuracy is acquired as shown in the experimental result.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.791-800
• /
• 2022

The number and locations of force generators and their force directions of Active Vibration Control System(AVCS) are important to maximize the airframe vibration reduction performance of helicopters. The present AVCS simulation using an exhaustive test method attempts to determine the best number and locations of force generators and their force directions for maximization of the airframe vibration reduction performance of UH-60A helicopter at 158 knots. The 4P hub vibratory loads of the UH-60A helicopter are calculated using DYMORE II, a nonlinear multibody dynamics analysis code, and MSC.NASTRAN is used to predict the vibration responses of the UH-60A airframe. The AVCS framework with an exhaustive test method is constructed using MATLAB Simulink. As a result, when applying AVCS with the optimal combination of the force generators, the 4P airframe vibration responses of UH-60A helicopter are reduced by from 19.35% to 98.07% compared to the baseline results without AVCS.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.2
• /
• pp.61-68
• /
• 2005

This paper is concerned with attitude control of 2 rotor 1 DOF aerial vehicle. The proposed controller consists of two parts: the attitude estimation filter part and PID controller part. For attitude estimation, performance of 3 different filters (complementary filters, Kalman filter, indirect Kalman filters) are tested and compared. For the PID controller, characteristic ratio assignment methods are used to assign PID coefficients. Through experiments, it is shown that attitude of the vehicle successfully follows the step command.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.3
• /
• pp.233-239
• /
• 2013

A 100 W fuel cell system using chemical storage method has been applied for a propulsion system of the SUAV(Small Unmanned Aerial Vehicle). A fuel cell and battery have been combined for both the small/light hydrogen generation control system and the hybrid power supply system. A small hydrogen generation device was implemented to utilize NaBH4 aqueous solution and dead-end type PEMFC system, which were evaluated on the ground and by the flight tests. The system pressurized at a 45kpa stably operates and get higher fuel efficiency. The pressure inside of the hydrogen generation control system was maintained at between 45 kPa and 55 kPa. The 100W fuel cell system satisfies the required weight and power consumption rate as well as the propulsion system, and the fuel cell system performance was demonstrated through flight test.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.2
• /
• pp.437-447
• /
• 2020

The purpose of this study is to research the countermeasures and expected effects through the use of drones in the field of disaster prevention as a drone-based smart quarantine performance method. The environmental, market, and technological approaches to the review of the current quarantine performance task and its countermeasures are as follows. First, in terms of the environment, the effectiveness of the quarantine performance business using drone-based control is to broaden the utilization of forest, bird flu, livestock, facility areas, mosquito larvae, pests, and to simplify and provide various effective prevention systems such as AI and cholera. Second, in terms of market, the standardization of livestock and livestock quarantine laws and regulations according to the use of disinfection and quarantine missions using domestic standardized drones through the introduction of new technologies in the quarantine method, shared growth of related industries and discovery of new markets, and animal disease prevention It brings about the effect of annual budget savings. Third, the technical aspects are (1) on-site application of disinfection and prevention using multi-drone, a new form of animal disease prevention, (2) innovation in the drone industry software field, and (3) diversification of the industry with an integrated drone control / control system applicable to various markets. (4) Big data drone moving path 3D spatial information analysis precise drone traffic information ensures high flight safety, (5) Multiple drones can simultaneously auto-operate and fly, enabling low-cost, high-efficiency system deployment, (6) High precision that this was considered due to the increase in drone users by sector due to the necessity of airplane technology. This study was prepared based on literature surveys and expert opinions, and the future research field needs to prove its effectiveness based on empirical data on drone-based services. The expected effect of this study is to contribute to the active use of drones for disaster prevention work and to establish policies related to them.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.87-91
• /
• 2004

It is definitely required to control dispersion of the rocket engine performance in order to accomplish the mission of launch vehicle successfully. We performed the dispersion analysis of gas generator cycle LRE (liquid rocket engine) accompanied with ANASYN. As a result, the vacuum thrust dispersion of the engine was $+5.34\%,\;-5.27\%$ and the mixture ratio deviated $+9.07\%,\;-9.82\%$ from the nominal value due to the errors of components and engine inlet condition of propellants. By applying the gas generator regulator only, the dispersion of the engine performance increases. Error in turbine efficiency is the most influential factor to the dispersion of engine performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.1-11
• /
• 1999

Thermal behavior of spacecraft propulsion system utilizing monopropellant hydrazine ($N_2$$H_4$) is addressed in this paper. Thermal control performance to prevent propellant freezing in spacecraft-operational orbit was test-verified under simulated on-orbit environment. The on-orbit environment was thermally achieved in space-simulation chamber and by the absorbed-heat flux method that implements an artificial heating through to the spacecraft bus panels enclosing the propulsion system. Test results obtained in terms of temperature history of propulsion components are presented and reduced into duty cycles of the avionics heaters which are dedicated to thermal control of those components. The duty cycles are subsequently converted into the electrical power required in the operational orbit. Additionally, cyclic temperature of each component, which was made under thermal-balanced condition of spacecraft, is compared to the acceptable design range and justified from the viewpoint of system verification.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.82-82
• /
• 2023

홍수기 하천에서 유량측정은 예산, 인력, 안전 및 측정 시 편의성 등의 이유로 측정에 제한이 많다. 특히, 태풍 등으로 인한 호우사상 발생 시 위와 같은 문제로 홍수량 측정에 어려움이 따른다. 이러한 문제점을 개선하기 위해 Lee et al.(2021)은 드론과 전자파표면유속계의 기능을 융합한 DSVM(Dron and Surface Veloctity Meter using doppler radar) 측정방법을 개발하였다. 전자파표면유속계 측정의 제한 요소인 진동을 감소시키기 위해 댐퍼플레이트를 개발하였고 금강의 지류인 봉황천에 현장 적용을 통해 DSVM 측정방법의 실용성을 확인하였다. 기존 연구에서 DSVM 방법은 드론의 각 측선 이동을 위한 조종과 전자파표면유속계 측정의 제어를 측정자가 수행하였는데 본 연구에서는 통합 드론측정시스템(IDMS, Integrated Drone Measurement System) 개발을 통해 측정자의 조종 의존도를 줄임과 동시에 안전하고 정확한 유량측정을 위해 노력하였다. 기존 댐퍼플레이트의 상하 진동 흡수 기능뿐만 아니라 전자파표면유속계의 흔들림 현상 등 자세 제어 기능을 보완하기 3축 모터를 적용한 방수짐벌을 개발하여 측정 정확도를 향상시켰다. 미션컴퓨터 개발로 측정지점의 측정 임무정보를 DB화하여 각 측선별 헤딩, 고도, 이동 등 자동항법 기능과 기체의 안정화 이후 전자파표면유속계를 자동으로 제어하여 측정을 실시하는 기능을 구현하였다. 또한 통합 GCS(Ground Control System)를 통해 비행 및 측정에 대한 모든 정보를 확인하고 컨트롤 할 수 있게 하였다. 2022년 금산군(제원대교), 무주군(취수장), 경주시(서천교) 지점에서 홍수기 유량측정에 도입하여 중간단면적법, 지표유속법을 적용하여 통합드론측정시스템의 실용성을 검증 완료하였다. 2023년 현장에 18대의 통합 드론측정시스템을 도입하여 홍수기 유량측정에 활용할 계획이다.