• Journal of the Korean earth science society
• /
• v.32 no.1
• /
• pp.1-11
• /
• 2011

The impact echo and impulse response methods were applied to the safety inspection of concrete structure, which has the rear cavity. The concrete structure model used in this study was divided into four sections, pure concrete, concrete+cavity, reinforced concrete with iron bar, and reinforced concrete+cavity, respectively. Previous study performed by authors have showed a possibility of success to use these method for detection of the rear cavity of concrete structure. Therefore, we tried to get more enhanced result with IE and IR methods through this study. Especially, IE and IR methods are relatively accurate to map the point of measurement, which makes it possible to interpret the depth of the concrete bed and effect by rear cavity with confidence. Followings were revealed from the results; the IE method shows some small peak zones probably indicating the rear cavity in the frequency lower than the resonance frequency and the changes of mobility and dynamic stiffness in the IR method indicate the weak zones. The proposed methods can be used to delineate the weak zones of the concrete structure.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1075-1081
• /
• 2010

Recently, the results of many studies have clarified the successful performance of magnetostrictive transducers in which a ferromagnetic patch is used for the transduction of guided shear waves; this is because a thin ferromagnetic patch with strong magnetostriction is very useful for generating and detecting shear wave. This investigation deals with bulk shear wave transduction by means of magnetostriction; on the other hand, the existing studies have been focused on guided shear waves. A modular transducer was developed; this transducer comprised a coil, magnets, and a thin ferromagnetic patch that was made of Fe-Co alloy. Some experiments were conducted to verify the performance of the developed transducer. Radiation directivity pattern of the developed transducer was obtained, and a test to detect the damage on a side drill hole of a steel block specimen was carried out. From the results of these tests, the good performance of the transducer for nondestructive testing was verified on the basis of the signal-to-noise ratio and narrow beam directivity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.164-172
• /
• 2020

The fuel oil/heat exchanger installed in military aircraft is a device that cools the lubricant oil supplied to other devices, such as an AMAD, and a hydraulic pump using the low temperature of the fuel is cracked at the AMAD lubricant inlet port. If a crack in the heat exchanger occurs, the lubricant oil supplied to other equipment is not cooled. Therefore, the flight can no longer be performed. In this study, non-destructive inspection and microscopic examination of the fracture surface of the oil port were performed to analyze the crack tendency. The oil pipe connected to the oil port is a titanium pipe, which is fastened with over torque and has been identified as the leading cause of heat exchanger oil port cracks. In addition, it was verified as the main reason for cracking by finite element analysis. The material and diameter of the pipe were changed to improve this defect, and the applied torque was adjusted. In addition, the bending value of the pipe was adjusted to minimize the fatigue accumulation due to pulsating pressure. As a result, no cracks occurred on the heat exchanger via the ground test after the installation of an improved pipe under the same conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.19-28
• /
• 2012

In this study, cause of longitudinal crack which is found on duct slab of road tunnel is studied. In-depth investigation, such as visual inspection, non-destructive testing and geometrical surveying of duct slab, is carried out. In order to perform cause analysis, the investigated results are compared to the results of numerical analysis. Many factors, which cause longitudinal crack, are classified as constrained condition of the duct slab, location of the rebar, temperature, shrinkage and so on. According to the classified causes of longitudinal crack, numerical analysis is performed considering construction stage of the tunnel lining. Especially, in order to predict shrinkage stain due to discrepancy of curing date, ACI-209 model, KCI structural design code and other researcher's shrinkage test results are compared. The results show that shrinkage strain is one of the main factors causing longitudinal crack. Other investigated tunnels are classified along with the construction method of duct slab and patterns of cracks. As a result, improving ways to construct duct slab are suggested.

• Economic and Environmental Geology
• /
• v.26 no.2
• /
• pp.167-174
• /
• 1993

Limited geochemical components have been detected in fluid inclusions from ore deposits in south Korea by non-destructive and destructive analytical methods. Review of fluid inclusion studies display that the homogenization temperatures and salinities are in direct proportion. W and Cu ore deposits tend to show higher homogenization temperatures and salinities than Au ore deposits. Abundant halite-bearing fluid inclusions from the Eonyang Granite producing precious amethyst crystals may indicate that the initial fluid originated from magma is highly saline as shown by the quartz from the granite. Raman Laser microprobe detected $CO_2$, $N_2$ and $CH_4$ in a gold deposit, while these components are hardly detected from other deposits, even though destrucive analysis has dectected $CO_2$, $N_2$, $CH_4$, $H_2S$, and $SO_2$ from most of ore deposits. Individual fluid inclusion shows quite different components. These results suggest that large numbers of fluid inclusions should be analysed by Raman Laser microprobe to gain reliable data. Halite-bearing inclusion is hardly found in fluid inclusions from epithermal gold deposits in south Korea. Geochemistry, homogeinzation temperature and salinity of fluid inclusions may be useful to apply for exploration to find a concealed orebody.

• Economic and Environmental Geology
• /
• v.40 no.5
• /
• pp.661-673
• /
• 2007

Rock materials of the three-storied stone pagoda in the Cheongryongsa temple in Korea are mainly composed of gneissose two-mica granite and fine-grained granite. This stone pagoda shows structural instability due to cracks and breaking-out of the stones. The surface properties of the stone is highly degraded by various inorganic pollutants and epilithic biospecies. Therefore, this study carried out comprehensive deterioration diagnosis by non-destructive methods, and some conservation treatments base on the diagnosis were carried out to reduce weathering progress. As the treatments, the biospecies and lichen that covering on the stone surfaces were removed by dry and wet cleaning, and degraded concrete applied to the pagoda for restoration in the past was removed and repaired with epoxy resin. Oxidized iron plates inserted between the rock properties were also substituted titanium stainless steels. After all processes are completed, we sprayed consolidant on the rock surface. Finally, the ground of the stone pagoda was rearranged using small rock aggregates, and the fence was established for control of artificial deterioration by visitors and environmental maintenance.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.4
• /
• pp.321-326
• /
• 2002

Near infrared spectroscopy (NIR), is recently applied to analysis of food, and it gives non-destructive and highly reproducible results. The objectives of this study were to assay protein, lipid and starch content in Alaska pollack surimi and to investigate application in seafood. NIR spectra showed the absorbance signal at 1,510 nm, 2,050 nm, 2,170 nm and 2,180 nm for protein, and signal were increased with protein content. Standard error of equation (SEE) was 0,296 and standard error of prediction (SEP) was 0.327. In analysis of lipid in Alaska pollack surimi by NIR, near infrared spectra of lyophilized Alaska pollack surimi were scanned and the signals of absorbance from C-H functional groups in lipid were identified at 1,730 nm, 1,740 nm and 2,300 nm and these signals were risen as Increasing lipid contents of Alaska pollack surimi as samely protein. SEE and SEP were 0.319, 0,353, respectively. In starch analysis using NIR the signals of starch distinctly changed at wavelength of 1,450 nm and 1,950 nm. Collected values of SEE and SEP were 0.304 and 0.318, respectively and the range of errors was $0.0186\~0.6470$ in starch contents.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.1
• /
• pp.35-42
• /
• 2008

In the nuclear power plant, early detection of fatigue crack by non-destructive test (NDT) equipment due to the thermal cyclic load is very important in terms of strict safety regulation. To this end, many efforts are exerted to the fabrication of artificial cracked specimen for practicing engineers in the NDT company. The crack of this kind, however, cannot be made by conventional machining, but should be made under thermal cyclic load that is close to the in-situ condition, which takes tremendous time due to the repetition. In this study, thermal loading condition is investigated to minimize the time for fabricating the cracked specimen using simulation technique which predicts the crack initiation and propagation behavior. Simulation and experiment are conducted under an initial assumed condition for validation purpose. A number of simulations are conducted next under a variety of heating and cooling conditions, from which the best solution to achieve minimum time for crack with wanted size is found. In the simulation, general purpose software ANSYS is used for the stress analysis, MATLAB is used to compute crack initiation life, and ZENCRACK, which is special purpose software for crack growth prediction, is used to compute crack propagation life. As a result of the study, the time for the crack to reach the size of 1mm is predicted from the 418 hours at the initial condition to the 319 hours at the optimum condition, which is about 24% reduction.

• Journal of Korean Society of Forest Science
• /
• v.106 no.1
• /
• pp.70-76
• /
• 2017

Among the forest road pavement methods, the majority of current constructions utilize concrete pavements but it has disadvantages as follows: many cracked concrete pavements generated by the erosion of underlying soil layers, could not be used as forest roads in steep slope during winter, and cement contains hazardous chemicals (hexavalent chromium, etc.). In order to supplement the limitations of the use of concrete pavement, this study was conducted to investigate the operation process and cost, the strength and compaction of the experimental forest road pavement(85 m) utilizing eco-friendly solidification material at Goryeong-gun, Gyeongsangbuk-do. The work elements of experimental forest road paving were classified into: preparation, Roadbed excavation, Roadbed grading, subgrade compaction, form work, collection and selection of site soil, mixing site soil and eco-friendly solidification material, paving by eco-friendly solidification material, compaction by vibrating roller and curing. The result of economic analysis using construction cost shows that for concrete costs total to $38,681won/m^3$ while for the eco-friendly paving material it is $38,245won/m^3$. Thus the construction costs for concrete and the eco-friendly paving material are similar. And the results of the Schmidt Hammer test for strength analysis by curing period are 10.5-13.5 MPa for 7 days, 18.1-22.7 MPa for 14 days, and 20.8-23.0 MPa for 28 days.

• Korean Journal of Food Science and Technology
• /
• v.40 no.2
• /
• pp.135-140
• /
• 2008

In this study, the macromineral content ratios of four herbal medicine samples(Saposhnikoviae Radix, Bupleuri Radix, Cnidii Rhizoma, and Astragali Radix) were analyzed to discriminate their geographical origins using an energydispersive x-ray fluorescence (EDXRF) technique. EDXRF is a rapid, non-destructive, and multi-elemental analysis technique. Initially, samples of both domestic and imported herbal medicines were pulverized, and then their macromineral contents, including P, S, K, and Ca, were analyzed using EDXRF. For the discrimination of their geographical origins, canonical discriminant analysis was carried out based on the estimated macromineral relative content ratios of the samples. According to the results, the discrimination accuracies were as follows: 93.3% for Saposhnikoviae Radix, 95.7% for Bupleuri Radix, 98.8% for Cnidii Rhizoma, and 87.5% for Astragali Radix. Overall, the results imply that this technique could be used as a standard method, to discriminate their geographical origins between domestic and imported herbal medicines.