• 비파괴검사학회지
• /
• 제22권6호
• /
• pp.643-648
• /
• 2002

In this study, shearography and ESPI have been used for quantitative analysis of an inside crack of pipeline and both of them appeared suitable to qualitatively detect inside crack. However, shearography needs several effective factors including the amount of shearing, shearing direction and induced load for the quantitative evaluation of the inside crack. In this study, the factors were optimized for the quantitative analysis and the site of cracks has been determined. Although the effective factors in shearography has been optimized, it is difficult to determine the factors exactly because they are related to the details of tracks. On the other hand, ESPI is independent on the details of a crack and only the induced load plays an important role. The out-of-plane displacement was measured under the optimized load and the measured were numerically differentiated, which resulted in an equivalent to the shearogram. The size of cracks can be determined quantitatively without any detail of a crack.

• 비파괴검사학회지
• /
• 제21권1호
• /
• pp.1-21
• /
• 2001

It will be shown how models can simulate all the elements of an ultrasonic NDE measurement system, including the pulser/receiver, cabling, transducer(s), and the acoustic/elastic waves fields. When combined, these models form what is called the electroacoustic measurement model. It will be demonstrated how this electroacoustic measurement model can be used to conduct parametric transducer and system studies and how the model can form the basis for experimentally characterizing all the elements of the ultrasonic measurement system, using purely electrical measurements.

• 비파괴검사학회지
• /
• 제21권1호
• /
• pp.22-31
• /
• 2001

Some techniques developed recently for sizing smalt fatigue cracks are described. One is an ultrasonic technique which deals with a small closed crack, where both the stress closing the crack and the crack size are determined by analyzing inverse problem. Here, difficulties encountered in NDE of closed cracks by usual ultrasonic techniques are summarized in advance. Secondly, the closely coupled probes potential drop (CCPPD) technique, which is based on d-c potential drop measurement, is explained fur sizing small cracks. The CCPPD technique is not affected by crack closure. Finally, a discussion is given on NDE of materials degradation in conjunction with sensitive NDE of small cracks.

• 비파괴검사학회지
• /
• 제22권6호
• /
• pp.649-658
• /
• 2002

As an attempt to further improve the reliability and effectiveness of ultrasonic testing (UT), a two-dimensional numerical simulator of UT was developed. The simulator models the wave medium (or test object) using the mass-spring lattice model (MSLM) that consists of mass-points and springs. Some previous simulation results, obtained by using MSLM, are briefly reviewed in this paper, for propagation, reflection, and scattering of ultrasonic waves. Next, the models of transmitting and receiving piezoelectric transducers are introduced with some numerical results, which is a main focus of this paper. The UT simulator, established by combining the transducer models with the MSLM, was used to simulate many UT setups. In this paper, two simple setups are considered as examples, and their simulated A-scan signals are discussed. The potential of the MSLM, transducer models, and the UT simulator developed in this study to be used in the actual UT is confirmed.

• 비파괴검사학회지
• /
• 제12권2호
• /
• pp.21-29
• /
• 1992

Acceleration signal characteristics of a steel plate, impacted by steel balls, were studied in an attempt to apply the experimental results to the impact location and mass estimation of metallic loose parts in the cooling system of nuclear power plants. Experimental results show that the variation of maximum acceleration amplitude and impact contact time due to the change of ball mass and impact velocity can be well explained by the Hertz impact theory. The frequency spectral pattern shifted slightly in spite of the increase of impact velocity and impact location. Ball mass, however, strongly affected the frequency spectral pattern. Hence the frequency spectrum can be used for estimation of the mass of unknown loose parts in the cooling system.

• 비파괴검사학회지
• /
• 제12권2호
• /
• pp.7-13
• /
• 1992

In this study, we examine the characteristics of beam and the effect of these characteristics on the flaw detection by using different type of two transducers, which are PZT and PVDF film transducer. Consequently, the detection of infinitesimal flaw is more possible than PZT, since it has beam width at focus of $60%{\sim}65%$ in contrast with PZT's. Moreover we can know PVDF transducer has superiority in detecting ability for sub-surface flaw detection in view of its acoustic impedance is near to water's and its focusing range is narrower than PZT's as $65{\sim}85%$ because it has spherical surface.

• 비파괴검사학회지
• /
• 제12권3호
• /
• pp.12-19
• /
• 1992

This paper shows that the identified and unidentified components of surface roughness in NC turning lathe which can not be analyzed in time domain such as $R_{max},\;R_a$ can be isolated in frequency domain by FFT analyzer. By interfacing FFT analyzer with stylus surface roughness instrument, surface roughness on change of working condition, especially tool feed, such as 0.1, 0.15, 0.2, 0.25, 0.3(mm/rev) can be analyzed in frequency domain as follows. 1. By frequency analysis of surface roughness profile, the basic wave length of surface roughness can be obtained to isolate the identified and unidentified components of surface roughness. 2. With increase of tool feed, the unidentified components of surface roughness increase. 3. Since $R_{max}$, which can be obtained by stylus surface roughness is proportion to the output voltage of FFT analyzer, FFT analyzer also can be used to measure surface roughness in time domain such $R_a,\;R_{max}$.

• 비파괴검사학회지
• /
• 제12권3호
• /
• pp.33-39
• /
• 1992

This paper presents a summary of the immersion ultrasonic test to analyze the quality of diffusion bonding parts. The most important property of diffusion bonding parts is bonding strength, and that can be obtained by shear test. By comparing among data obtained by ultrasonic test(C-Scan) and those by shear test (bonding strength), these data are shown to be in good relation. Therefore ultrasonic C-Scan test result can be used successfully in quantitative quality control for diffusion bonded parts.

• 비파괴검사학회지
• /
• 제24권1호
• /
• pp.52-63
• /
• 2004

The importance of nondestructive testings and its international standardization are well recognized not only in the developed countries and but also in the developing countries in recent years. In order to deal with the international standardization for nondestructive testing, the ISO/TC 135 meeting was held in Cheju island, Republic of Korea from 28th to 31st, October, 2003. In this period, the meetings of subcommittee 2, 5, 6, 7, and SC 7 WG 7 were also held. Here summarized are the results of the meetings and the status of ISO/TC 135. In addition, the major revisions of ISO 9712 to be included in 2004 edition are discussed in detail.

• 비파괴검사학회지
• /
• 제23권3호
• /
• pp.270-279
• /
• 2003

Parametric studies have been conducted into the variability of the factors affecting the ultrasonic testing applied to weldments. The influence of ultrasonic equipment, transducer parameters, test technique, job parameters, defect type and characteristics on reliability far defect detection and sizing was investigated by experimentation. The investigation was able to build up substantial bank of information on the reliability of manual ultrasonic method for testing weldments. The major findings of the study separate into two parts, one dealing with correlation between ultrasonic techniques, equipment and defect parameters and inspection performance effectiveness and other with human factors. Defect detection abilities are dependent on the training, experience and proficiency of the UT operators, the equipment used, the effectiveness of procedures and techniques.