• Journal of the Korean GEO-environmental Society
• /
• v.12 no.3
• /
• pp.47-54
• /
• 2011

The rockfall protection fence installed to secure safety against rockfall occurring in cut slope has been designed under the condition with 50kJ of impact energy arising when the 400kg of rock block is falling from 12.5m height. However, in falling case of bigger rock block or from higher place, it is hard to be secure of safety with existing rockfall protection fence. Using the rockfall program, safety analysis for rockfall is conducted in this paper by changing slope height, separating distance from fence, and slope angle, according to rock block sizes. In the result of analysis, when a 400kg of rock block which is designed load is fallen, the existing rockfall protection fence with 2.5m height can secure most of rock fall except some cases for the slope having 20m or less hight, whereas for more than 20m height, the fallen rock is frequently splattered over the rockfall protection fence, as well as the impact energy of rockfall may exceed designed impact energy. Therefore, in the design of rock fence, it is considered appropriate to design that after conducting safety review for rockfall according to the ground conditions, evaluating the bounce height and impact energy of rock fall, and then installing appropriate rockfall protection fence would be applicable rather than just following standards based design drawing.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.3
• /
• pp.11-22
• /
• 2019

This study was conducted to identify the causes of the unusually high number of rock slope failures during an expressway construction in Yangsan fault system. The shear strength (cohesion and internal friction angle) of 128 slopes of discontinuities including bedding, joint, and fault planes were re-evaluated through the examination of face mapping and back analysis. The re-evaluated values were analyzed and then compared with the existing data and values used in the design. As a result, the re-evaluated cohesion and friction angles were very low compared to the existing data and the values applied in the design. This incongruity was pointed as the primary reason for the rock slopes failures during the construction. This may be related to the inherent features of clastic sedimentary rocks in the study area, and the discontinuities in the sedimentary rocks in this region played a significant role. Especially, bedding discontinuity showed a big difference compared to the existing data. The shear strength depended on the type of discontinuity in case of clay filled in discontinuity. However, shear strength was independent on the type of discontinuity in case of shattered materials filled in discontinuity.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.1
• /
• pp.49-57
• /
• 2022

In order to efficiently analysis the stability of a slope, measuring the shear strength of soil is needed. The Standard Penetration Test (SPT) is not appropriate for a slope inspection due to cost and weights. One of the ways to effectively measure the N-value is the Dynamic Cone Penetration Test (DCPT). This study was performed to develop a minimized multi-function sensors that can easily estimate CPT values and Volumetric Water Content. N value with multi-fuction sensor DCPT showed -2.5 ~ +3.9% error compared with the SPT N value (reference value) in the field tests. Also, the developed multi-fuction sensor system was tested the correlation between the CPT test and the portable tester with indoor test. The test result showed 0.85 R2 value in soil, 0.83 in weathered soil, and 0.98 in mixed soil. As a result of the field test, the multi-function sensor shows the excellent field applicability of the proposed sensor system. After further research, it is expected that the portable multi-function sensor will be useful for general slope inspection.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.1
• /
• pp.139-152
• /
• 2018

This study is an analysis of slope failure examples of cut sedimentary hills during construction road in Kyoungsang Basin, especially Yangsan Fault system (Ilkwang-Dongrae fault). This area involved a lot of hillslope failures compared to other areas during road construction. The exposed failure slopes were first face-mapped, and then back analyzed based on the limit equilibrium method to assess the shear strength parameters of discontinuity (bedding). The results of this analysis indicate that the shear strength parameters of discontinuity (bedding) are significantly smaller than those used in the design stage and presented in the existing works. The filling in the bedding and emerging groundwater may be decreasing strength parameters. Especially, the clay in the bedding plays a key role in the effect of the shear strength. The study also suggests that the bedding angle and the internal friction angle are proportional to each other. Using this relationship and knowing the bedding angle, the friction can easily be estimated.

• Tunnel and Underground Space
• /
• v.18 no.4
• /
• pp.289-299
• /
• 2008

Based on the case study on the causes for the failure of cutting slope composed of weathered rock and soil, the factors influencing the design of a cutting slope have been examined, This type of rock and soil is widely distributed on the region whose parent rock is granite. To analyze the stability of the cutting slope, the following series of progress has been conducted: (1) ground characterization by geological survey and ground investigation, (2) the safety factor examination by limit equilibrium analysis and numerical analysis and (3) the comparison and analysis of rainfall and failure history. As a result, the main factors to cause the failure is determined to be the decrease of shear strength in the upper parts whose ground condition is weakened during localized heavy rain. Moreover, the analysis indicates the failure is also closely related to the groundwater inflow path. On the base of this investigation, a reinforcement method is proposed to ensure the stability of the cutting slope.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.3
• /
• pp.5-17
• /
• 2021

This study aims to investigate the causes and countermeasures for the occurrence of tension cracks in the slope of the rock mass of heavy equipment for road construction. Electric resistivity survey was performed to investigate the expandable tensile crack range. As a result of examining the distribution of soft zones in the rock mass, a low specific resistance zone was found at the bottom of the access road where tensile cracks occurred. It was confirmed that a low resistivity zone was distributed near the top of the excavation slope. Therefore, reinforcements was performed by determining the location of the possible tensile crack as the top of the excavation slope. Two rows of reinforced piles and anchors were proposed as a reinforcement method, and the slope stability analysis showed that the allowable safety factor was satisfied after reinforcements.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.11
• /
• pp.25-31
• /
• 2023

Horizontal drainage, which are representative dewatering method of domestic and foreign slope, are applied to reducing pore water pressure. Accordingly, several previous studies have been conducted, but horizontal drainage are standardized which is an unclean standard for a quantity calculation in filed. Therefore, this study presents field soil and laboratory model box to identify a drainage performance and influencing factors of various horizontal drainage. Furthermore, this study verifies the performance comparison of drainage shape or size according to different particle size distributions. In the outflow results for steady state, the study found that all samples are drained at a constant rate after a minimum of 3 minutes to maximum of 15 minutes. In the case of comparing the outflow per hour (Unit flux) in coarse grained soils, it found that drainage shape and size affect drainage performance. In the result, the future expected to be used basic data that experiment of drainage performance on fine grained soils and determine the quantity.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.4
• /
• pp.95-108
• /
• 2007

Test application of revegetation measure was made on the roadside slope damaged by Nongseo-Eomo national road improvement project in a bid to prevent the soil from being washed out as well as to restore the ecological environment, and the survey for assessment of the effect of slope revegetation measures was conducted, beginning May 11 through Nov 7, 2006. In the wake of comprehensive reviewing and evaluating the surrounding topographic environment, physical and chemical characteristics of soil, germination of revegetation plants, analysis of bio mass, covering ratio and the plants appeared, measure b was found to have been most appropriate to cut blasting rock slope, and alternatively measure c. For cut ripping rock slope, measure c-1 appeared to be effective in revegetation effect, and alternatively, b-1.When it comes to cut soil slope, measure c-2 was found to be effective, and b-2 to be a good alternative. And for embankment soil slope, measure b-3 appeared to be most efficient in revegetation effect and measure f as alternative.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.4
• /
• pp.83-94
• /
• 2007

Test application of revegetation measure was made on the roadside slope damaged by Gimcheon-Eomo national road improvement project in a bid to prevent the soil from being washed out as well as to restore the ecological environment, and the survey for assessing the effect of slope revegetation measures was conducted, beginning Sep 7 through Sep 20, 2006. In the wake of comprehensive reviewing and evaluating the surrounding topographic environment, physical and chemical characteristics of soil, germination of revegetation plants, analysis of bio mass, covering ratio and the plants appeared, revegetation measure C was found to have been most effective and desirable for further application in the area. Viewing the specific applicability by the area, revegetation measure C and C-1 appeared to be appropriate for blasting rock slope and ripping rock slope as they are efficient in preventing the slope from being washed out and in early revegetating. And revegetation measure B deemed to be effective to blasting rock slope or ripping rock slope as an alternative. And for cut slope, vegetation measure C-2 was judged to be more effective than measure D or E, while measure C-3 would be appropriateto embankment slope.

• Journal of the Korean GEO-environmental Society
• /
• v.5 no.4
• /
• pp.73-79
• /
• 2004

Mountain side ditch is constructed at the top of cutting slopes around road and it drains the surface water that flowed from upper part. Mountain side ditch is constructed to keep away the influx of the surface water into cutting faces. However, if Mountain side ditch is constructed on the top of cutting slopes, it is cause of trouble. For example, difficulty of quality control and lack of drainage faculty. Therefore, the faculty and establishment propriety of mountain side ditch are evaluated seriously, according to the condition of ground, topography and rainfall in this paper. Results from the study for the numerical analysis of effect of mountain side ditch indicate that safety factor is enlarged about 3% at rainfall.