• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.2
• /
• pp.221-233
• /
• 2016

In order to estimate the performance of a conical cutter depending on the insert size, this study measured forces acting on conical cutters with different cutter spacings, penetration depths and skew angles using slim and heavy conical cutters. When cutter spacings ranged from 12 to 27 mm, the deviations of mean cutter forces with cutter depths appeared smaller compared to other cutter spacings. When skew angle is $0^{\circ}$, the optimal S/d ratio was obtained in the range of 4 to 4.5 for which specific energy of cutting was minimized. It were usually found in the range of 1 to 5. However, when skew angle is $6^{\circ}$, the optimal S/d ratio was obtained in the range of 1 to 3. The simple comparison results shows that the performance of slim cutter was superior to that of heavy cutter, but the use of heavy cutter can be effective, considering the cutter consumption and cutter damage when the strength of the ground is high enough.

• Journal of the KSME
• /
• v.20 no.6
• /
• pp.474-488
• /
• 1980

이제까지의 결과를 종합하여 보면 다음과 같은 결론을 얻을 수 있다. 1. 국산 비피막공구는 의 산에 비하여 많은 절삭영역에서 양호한 성능을 가지고 있다. 2. 국산 비피막공구 W2는 중간 절 삭 영역에서 국산 W1과 외산 W3, W4보다 우수한 성능을 나타낸다. 3. W1은 저속이거나 절삭 깊이가 클 때, W2보다 좋은 성능을 가진다. 4. W1은 대체로 플랭크 마모에 의하여, W2는 저속. 저이송에서는 프랭크마모 그리고 그밖의 영역에서는 크레이터 마모에 의하여 수명이 결정된다. 5. 국산 피막공구 CW7은 외산 CW10, 13에 비하여 내마모성이 매우 좋다. 6. 중간절삭영역에서 W 2의 표면조도는 W1, W3, W4에 비하여 훨씬 좋다. 7. 피막층 유무와 피막재질에 따른 국산 및 외산의 절삭력 차이는 거의 없다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2048-2061
• /
• 1991

As compared with other cutting types, the ball end milling process causes a complexity in cutting system and a falling-off of machinability. In order to increase the productivity and efficiency in th NC machining of sculptured surfaces, this study carried out the qualitative linearized evaluation about the ball end milling system and applied their practical expressions to the technological processor at the cutter path planning stage. The evaluated expressions were proved to be adequate for practical use from an accuracy point of view and the estimation models were applied to sculptured surface machining processes for finding variable machining conditions. Consequently, it was recognized that variable machining conditions bring about the dispersion of force system and the reduction of machining time by more than 50%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.75-79
• /
• 1996

가공품 중에서 구멍가공이 차지하는 비율은 매우 높으며 또한 가공정밀도가 요구되어진다. 그러나구멍의 직경에 비하여 길이가 길어지면 칩의 배출, 절삭날부의 윤활이 어려워지고, 공구의 진동문제가있기 때문에 일반적인 가공으로는 불가능할 경우가 많다. 따라서 이에 적절한 가공방법은 고압력의 절삭유를 공급할 수 있는 공구를 이용하여 가공할 수 있으며, 그 대표적인 방법으로는 Spade Drill, Gun Drill, 및 BTA Dill에 의한 깊은구멍가공봅이다. 본 연구에서는 Single Tube BTA 드릴링 시스템에서 Single Edge BTA Drill을 사용 하여 깊은 구멍을 가공할 때 공작물 SM55C의 최적절삭 조건의 선정과 공구수명에 대하여 실험을 통하여 분석 하고자 하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.161-164
• /
• 1995

Nonlinear analysis of various phenomena has been developed with improvement of computer. The characteristics form nonlinear analysis are available in monitoring and diagnosis state of system. There are many nonlinear property in cutting process, but nonlinear signals have been considered as noise. In this study, nonlinear analysis technique is applied and it will be verified that cutting force is chaos by calculating Lyapunov exponents,fractal dimension and embedding dimension. The relation between characteristic parameter calculated form sensor signal and various cutting condition is investigated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.9
• /
• pp.1888-1896
• /
• 2002

This study presents a new type of CNC interpolator that is capable of generating cutter paths for ball-end milling of NURBS surfaces. The proposed surface interpolator comprises real-time algorithms for cutter contact (CC) path scheduling and CC path interpolator. Especially in this study, a new interpolator module to regulate cutting forces is developed. This propose algorithm utilizes variable-feedrate commands along the CC path according to the curvature of machined surfaces during the interpolation process. Additionally, it proposes an OpenGL graphic library for computer graphics and animation of interpolated tool-position display. The proposed interpolator is evaluated and compared with the existing method based on constant feedrates through computer simulations.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.6
• /
• pp.585-597
• /
• 2014

In this study, the cutter acting forces were measured by 3-directional load cell at two different skew angles and various S/d ratios during a series of linear cutting tests using a slim conical pick. The analysis for cutting performance were carried out after calculating average values of the measured results. The increase of penetration depth results in the decrease of specific energy. And the variations of the cutter acting forces depending on penetration depth in the case of 6 degree skew angle were smaller than in the case of 0 degree skew angle. From this results, 6 degree skew angle is more effective than 0 degree skew angle in designing optimal specifications of cutting head. In addition, $F_c/F_n$ under the setting of 6 degree skew angle was smaller than under the setting of 0 degree skew angle. However, it should be considered that the increase of cutter acting force in the cutting direction accompanied the increase of driving force in the case of the setting for 6 degree skew angle.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.93-98
• /
• 2004

A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured culling forces obtained from machining experiments

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1042-1047
• /
• 2001

A mechanistic model is developed to predict the thrust force and cutting torque of drilling process including wear. A mechanistic oblique cutting force model is used to develop the drilling force model. The cutting lips are divided into small elements and elemental forces are calculated by multiplying the specific cutting pressure with the elemental chip area. The specific cutting pressure is a function of chip thickness, cutting velocity, rake angle and wear. The total forces are then computed by summing the elemental forces. Measured cutting forces are in good agreement with the simulated cutting forces.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.1-9
• /
• 2004

For improvement of productivity and cutting tool lift, cutting force in end milling needs to be predicted accurately. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting force coefficients of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, fled, axial depth and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments.