• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.123-130
• /
• 1994

일반적으로 규칙파 또는 불규칙파중에서의 반잠수식 해양구조물의 응답을 추정할때, 선형계에 적합한 주파수 영역해석법을 사용하고 있다. 대다수의 해양구조물은 Lower Hull과 단면적이 일정한 Column으로 구성되어 있지만, 만약 Column의 단면적이 홀수에 따라 변화한다면 복원력항에 비선형계를 적용해야만 한다. 따라서 본 논문에서는 비선형 복원력을 고려한 반잠수식 해양구조물의 응답을 추정할 수 있는 시간 영역 해석법을 개발하였다. 그리고, Column형상이 다른 5개의 모델을 선정하여, 이들의 시간 영역 해석결과와 주파수 영역 해석 결과를 서로 비교하였다. 또한 파랑외력으로서 불규칙파를 적용할 때, 비선형 복원력이 해양구조물에 응답에 미치는 영향을 조사 하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.111-119
• /
• 2005

The objective of this study is to predict fracture movements accurately and reliably by nonlinear analysis of the response of RC shear wall or RC flange sections. Hognestad's and Vallenas's theories are used for concrete model and Ramberg-Osgood's theory is used for steel model. Non-linear analysis considering confined concrete and unconfined concrete is performed. Mander's Fiber Approach Section analysis, new strain profile considering the Gamma factor are used to this section analysis. The section analysis considering cases of precracked, uncracked, boundary warping and shear warping is performed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.3
• /
• pp.255-263
• /
• 2017

This paper presents a beam element capable of conducting material and geometric nonlinear analysis for applications requiring the ultimate behavioral analysis of structures with composite cross-sections. The element formulation is based on co-rotational kinematics to simulate geometrically nonlinear behaviors, and it uses the fiber section method to calculate the stiffness and internal forces of the element. The proposed element was implemented using an in-house numerical program in which an arc-length method was adopted to trace severe nonlinear responses(such as snap-through or snapback), as well as ductile behavior after the peak load. To verify the proposed method of element formulation and the accuracy of the program that was used to employ the element, several numerical studies were conducted and the results from these numerical models were compared with those of three-dimensional continuum models and previous studies, to demonstrate the accuracy and computational efficiency of the element. Additionally, by evaluating an example case of a frame structure with a composite member, the effects of differences between composite material properties such as the elastic modulus ratio and strength ratio were analyzed. It was found that increasing the elastic modulus of the external layer of a composite cross-section caused quasi-brittle behavior, while similar responses of the composite structure to those of homogeneous and linear materials were shown to increase the yield strength of the external layer.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.10a
• /
• pp.247-249
• /
• 2013

열화한 철근콘크리트 구조물에 대하여 성능회복을 위하여 전기화학적 방식, 단면복구공법, 균열보수공법, 표면마감공법 등이 상용되고 있다. 본 연구에서는 단면복구공법의 적용과 성능예측을 위한 해석 모델의 입력값으로 사용될 보강철근과 단면복구재의 부착특성을 평가하기 위하여 철근인발실험을 실시하였다. 폴리머시멘트몰탈이 사용되었으며 부착요소의 강성과 강도를 구하여 비선형 해석을 실시하여 상당한 정확도의 예측값을 도출하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.738-740
• /
• 2012

최근 변단면 거더의 경제성을 고려하여 장경간 거더 교량과 강골조 구조물에 변단면보의 사용이 증가하고 있으며, 고강도 강의 등장으로 인해 변단면보의 정확한 좌굴 강도의 평가가 매우 중요시 되고 있다. 본 논문에서는 기존에 연구된 탄성 횡-비틀림 좌굴 강도에 관한 연구를 바탕으로하여 별로 비탄성 구간에 비지지 길이가 존재하는 일축대칭 I형 변단면보의 횡-비틀림 좌굴 강도 해석을 실시하였다. 해석에는 유한요소해석프로그램인 ABAQUS(2007)가 사용되었으며, MINITAB(2006)을 이용하여 간편한 설계식을 제안하고 있다. 일단 계단식 단면을 가지는 보에 대하여 고려하였으며, 플랜지 길이 방향 비, 너비방향 비, 두께의 비로 계단식 I형 보를 나타내었다. 집중 하중을 적용시켰으며 비선형 해석을 위해 잔류응력 및 초기변형과 재료비선형을 고려하였다. 본 연구 결과에서 제안된 식은 향후 다양한 하중이 작용하는 비탄성 횡-비틀림 좌굴 강도에 대한 연구에 많은 도움이 될 것이다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.5
• /
• pp.28-33
• /
• 2005

Nonlinear aeroelastic characteristics of a two dimensional typical section model with bilinear plunge spring are investigated. Doublet-point method(DPM) is used for the calculation of supersonic unsteady aerodynamic forces which are approximated by using the minimum-state approximation. For nonlinear flutter analysis structural nonlinearity is represented by an asymmetric bilinear spring and is linearized by using the describing function method. The linear and nonlinear flutter analyses indicate that the flutter characteristics are significantly dependent on the frequency ratio. From the nonlinear flutter analysis, various types of limit cycle oscillations are observed in a wide range of air speeds below or above the linear flutter boundary. The nonlinear flutter characteristics and the nonlinear aeroelastic responses are investigated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1A
• /
• pp.53-60
• /
• 2009

This paper deals with the geometrical nonlinear analyses of post-buckled columns with variable cross-section. The objective columns having variable cross-section of the width, depth and square tapers are supported by both hinged ends. By using the Bernoulli-Euler beam theory, differential equations governing the elastica of post-buckled column and their boundary conditions are derived. The solution methods of these differential equations which have two unknown parameters are developed. As the numerical results, equilibrium paths, elasticas and stress resultants of the post-buckled columns are presented. Laboratory scaled experiments were conducted for validating the theories developed in this study.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.37-46
• /
• 2007

This is the second of two companion papers that describe non-prismatic beam element for nonlinear seismic analysis of steel moment frames. Described in a companion paper is the formulation of a non-prismatic beam element to model the elastic and inelastic behavior of steel beams, which have reduced beam sections(RBS). This study describes the determination of yield surfaces, stiffness parameters, and hardening (or softening) rule parameters for RBS beam element. Analytical results of the RBS beam element show good correlation with test data and Finite Element Method(FEM) results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.347-356
• /
• 2006

In this paper, practical nonlinear inelastic analysis method of 3-dimensional steel structures accounting for gradual yielding with fibers on a section is developed. Geometric nonlinearities of member(p-$\delta$) and frame(p-$\Delta$) are accounted for by using stability functions. Residual stresses are considered by assigning initial stresses to the fiber on the section. The elastic core in a section is investigated at every loading step to determine the axial and bending stiffness reduction. The strain reversal effect is captured by investigating the stress change of each fiber. The proposed analysis proves to be useful in applying for practical analysis and design of three-dimensional steel frames.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.577-585
• /
• 2006

In this research, nonlinear Timoshenko beam element that is able to capture nonlinear shear deformation is developed. The proposed model shows more reasonable prediction than Bernoulli beam theory in short columns or strong shear column due to the consideration of shear deformation. The cross-section is modeled as fiber approach. Since the model is based on the fiber approach for section discretization, the plastic progress of the section can be traced and the coupling effect of the axial and flexural response. The developed element is implemented into the finite element program to analysis general reinforced concrete structures. As parametric study, reinforced concrete columns are analyzed and compared with experimental results, analyzed the property of behavior for reinforced concrete columns.