• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.103-103
• /
• 2017

증발기의 형태에 따라 수치적 해석을 진행하면서 최적의 효율을 나타낼 수 있는 증발기를 설계하는 것이 중요하다. 증발기의 수치적 해석은 EES 프로그램을 이용하여 진행되었으며, 계산의 검증은 자사의 제품의 성능과 비교하면서 검증하였다. 증발기의 수치적 해석의 구성은 지배방정식과 연속방정식을 이용하여, 냉매의 총괄열전달계수, 관내외벽의 열전도율, 공기의 총괄열전달계수를 이용하여 총괄열전달계수를 계산하였으며, 총괄열전달계수를 이용하여 증발기의 열량을 계산하였다. 증발기의 수치적 해석과 자사 제품 5개의 제품과 비교하였고, 평균적으로 약 10%의 오차율을 보였다. 신뢰성이 확보된 계산식을 이용하여 Fin의 간격, 단위 질량유량, 열 교환 코일 길이, 풍량의 조건을 각각 변동시켜 증발기 열량 비교를 하며 경향성을 고찰하였다. Fin의 간격을 1mm에서 20mm으로 0.5mm 간격으로 변화 시켰을 경우, 핀 간격이 좁으면 공기 유속이 빨라져 열 교환 효율이 낮아지며, 반대로 넓어지면 냉매 유량에 비해 공기 유량이 많기 때문에 열 교환 효율이 낮아진다. 열 교환 코일 길이를 500mm에서 2400mm으로 50mm 간격으로 변화 시켰을 경우, 열 교환 코일 길이가 길어질수록 배관의 마찰력과 냉매의 온도 상승으로 인하여 공기 온도와의 온도 차이가 줄어들어 열 교환 효율은 낮아진다. 풍량을 20cmm에서 400cmm으로 10cmm 간격으로 변화 시켰을 경우, 일정 풍량 이상 올라가면 공기 유속이 빨라져서 열량이 낮아지는 경향을 보인다. 질량유량을 3g/sec에서 174g/sec으로 4.5g/sec 간격으로 변화 시켰을 경우, 질량 유량에 따라 비례적으로 열량이 높아지는 경향을 보이다가 일정 질량 유량 이상에서는 공기 풍량에 비해 냉매 유량이 많기 때문에 반비례적으로 열량이 낮아진다. 이처럼 증발기의 설계는 Fin 간격, 열 교환 코일 길이, 풍량, 질량유량 등을 복합적으로 고려하여 증발기 설계를 해야 하며, 저장고의 크기, 부하, 사용목적에 따라 최적화된 증발기를 설계하여야 한다.

• The Journal of Korean Society for Radiation Therapy
• /
• v.25 no.1
• /
• pp.9-14
• /
• 2013

Purpose: High-energy radiotherapy with 10 MV or higher develops photoneutron through photonuclear reaction. Photoneutron has higher radiation weighting factor than X-ray, thus low dose can greatly affect the human body. An accurate dosimetric calculation and consultation are needed. This study compared and analyzed the dose change of photoneutron in terms of space according to the size of photon beam energy and treatment methods. Materials and Methods: To measure the dose change of photoneutron by the size of photon beam energy, patients with the same therapy area were recruited and conventional plans with 10 MV and 15 MV were each made. To measure the difference between the two treatment methods, 10 MV conventional plan and 10 MV IMRT plan was made. A detector was placed at the point which was 100 cm away from the photon beam isocenter, which was placed in the center of $^3He$ proportional counter, and the photoneutron dose was measured. $^3He$ proportional counter was placed 50 cm longitudinally superior to and inferior to the couch with the central point as the standard to measure the dose change by position changes. A commercial program was used for dose change analysis. Results: The average integral dose by energy size was $220.27{\mu}Sv$ and $526.61{\mu}Sv$ in 10 MV and 15 MV conventional RT, respectively. The average dose increased 2.39 times in 15 MV conventional RT. The average photoneutron integral dose in conventional RT and IMRT with the same energy was $220.27{\mu}Sv$ and $308.27{\mu}Sv$ each; the dose in IMRT increased 1.40 times. The average photoneutron integral dose by measurement location resulted significantly higher in point 2 than 3 in conventional RT, 7.1% higher in 10 MV, and 3.0% higher in 15 MV. Conclusion: When high energy radiotherapy, it should consider energy selection, treatment method and patient position to reduce unnecessary dose by photoneutron. Also, the dose data of photoneutron needs to be systematized to find methods to apply computerization programs. This is considered to decrease secondary cancer probabilities and side effects due to radiation therapy and to minimize unnecessary dose for the patients.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.25-28
• /
• 2002

본 논문은 마이크로 프로세스로 처리되는 여러 제어장치들 중에서 PI제어기의 최적 자동동조에 관한 개선된 방법을 제안하고자 한다. 이 방법은 Relay 자동동조 법으로서 이를 마이크로 프로세스에 응용하여 제어대상에 최적의 PI계수를 입력하게된다. 이를 위해 먼저 Computer와 DSP사이에 통신이 가능하도록 RS-232를 설치하고, 컴퓨터의 제어신호에 따라 모터의 속도가 Relay와 PI제어기에 의해 목표값에 도달할 수 있도록 설계하였다. 내부적으로 사용된 Relay 동조방식은 Relay로 제어대상의 출력을 강제로 진등시켜서 출력의 진폭과 주기를 이용하여 PI 계수를 조정하고 제어기의 입력값으로 선택된다. Relay동조 법은 동조과정이 간단하여 동조 방식의 구현이 쉽다. 또 위상여유를 고려하여 제어기의 계수를 조정하기 때문에 시스템의 견실성을 향상시킬 수 있을 뿐 아니라, 비례 제어만으로 임계 진동을 하지 않는 시스템의 경우에도 사용할 수 있고, 원점에 극점이 있는 경우에도 적용할 수 있어서 기존의 제어방식이 가지는 제약성의 한계를 극복할 수 있어서 적용성이 우수하다.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.365-366
• /
• 2008

광학입자 계수기는 실내환경, 대기오염 및 콜린룸 등 입자크기분포 측정장비로 가장 많이 사용된다. 광학입자 계수기에 샘플링된 업자는 관측체적 내로 1개씩 통과 하며 산란된 빚은 집광장치에 의해 광검출기로 전달한다. 이때 산란광의 양에 비례하여 전압 (전류)의 세기로 변환하여 전기적 선호로서 나타나는 Pulse의 높이는 Calibration Data에 따라 업자의 크기로 변환하고 Pulse의 개수는 입자의 개수로 표시된다. 입자의 크기와 개수등 이용하여 부피로 환산 한 후 부유하는 입자의 평균 밀드를 이용하여 질량으로 환산시킨다. 이렇게 측정된 미세먼지 농도는 ZigBee 통신을 사용하여 구축한 시스템을 통해서 중앙부에서 실시간으로 먼지 농도를 알 수 있다. 특히 멀티흡 기능을 이용하여 건물 구조가 복잡하거나 층간의 통신, 꺾인 부분이나 사무실 안과 밖과 같은 무선 통신이 원할 하지 못하는 경우를 극복하여 미세먼지의 농도 값을 측정 할 수도 있다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.4
• /
• pp.123-128
• /
• 2017

This paper relates with the Hybrid-SMMA adaptive equalization algorithm that is possible to improve the equalization performance based on adaptive modulus and adaptive stepsize which is propotional to the output power of equalizer in the current SMMA (Sliced Multi Modulus Algorithm). The fixed statistic modulus of transmitted signal is used in current SMMA algorithm in order to generate the error signal for updating the tap coefficient of equalizer. The proposed Hybrid-SMMA based on the adaptive modulus which is propotion to the equalizer output signal power and adaptive stepsize which is fuction of the nonlinearties of error signal. The computer simulation was performed in order to confirm the improved equalization performance of proposed algorithm. As a result of computer simulation, the proposed Hybrid-SMMA has fairly good in every performance than the current SMMA.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.67-74
• /
• 2005

This paper concerns attitude controller design for a 3-staged launch vehicle which has movable nozzle TVC systems for all stages as its control systems. The PD-type control gains are determined by shaping the corresponding closed-loop natural frequencies for the purpose of guaranteeing the required stability margin. Bending filters are also designed to stabilize the bending modes by using parametric optimization method. The designed controllers are verified using six degree of freedom flight simulations in MATLAB.

• Applied Chemistry for Engineering
• /
• v.5 no.2
• /
• pp.223-229
• /
• 1994

The effect of agitation speed on mass transfer coefficient in the extraction of citric acid from mixed aqueous solutions of citric and acetic acid with n-butylacetate solutions of di-isotridecylamine(DITDA) and 50% mixture of tri-n-octyl and try-n-hexyl phosphine oxide(MOHPO), were studied in batch extractor. Experimental results showed that the degree of extraction was higher with increasing agitation speed, and was best at 200rpm and 30 minutes in batch extractor. The higher degree of extraction was obtained in mixed solution of citric-acetic acid by using DITDA than MOHPO as an carrier. Mass transfer coefficient was proportional to the degree of extraction, and $K_r=1.254{\times}10^{-3}Re^{0.536}$ was found for she extraction of citric acid by DITDA.

• Geotechnical Engineering
• /
• v.10 no.2
• /
• pp.85-96
• /
• 1994

Resonant column test huts been widely used as a primary laboratory testing technique in investigating dynamic soil properties expressed in therms of shear and Young's moduli and material damping. In thin Paper, dynamic Properties of typical Korean subgrade boils are investigated at shearing strains between 10-4% and 10-1% using Stokoe-type resonant column teat. The elastic threshold strains(yte) above which shear modulus and damping ratio are affected by strain amplitude, are defined at strain amplitude of about 10-3%. Below yte", small-strain shear modulus (Gmn) increases with confining pressure (Qc) as proportional to (Qe)0.61, and small-strain damping ratio(Dmin) ranges between 1% and 5.7%. Above yte, normalized shear modulus reduction curve(G/Gma. versus log strain) can be quite well expressed with Ramberg Osgood stress -strain equation and match well the curve suggested for sand by Seed and Idriss.riss.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.80-86
• /
• 2003

An anaysis on the discharge performance of an impinging-type injector for cavitating flow has been conducted by both numerical and experimental method. The predicted discharge coefficient for cavitating flow agrees well with the measured data showing less than 1% discrepancy. For the case of non-cavitating flow analysis, the disagreement between CFD results and the experimental data is 8%. The discharge coefficient for the cavitating flow decreases with decrease in the Reynolds number. On the other hand, it increases slightly as the Reynolds number increases for the non-cavitating flow because of the reduced viscous effect. From the present study, it is confirmed that the fact that cavitation phenomena should be included to predict accurately the discharge performance of injectors for cavitating flow regime. The uniformity of density and velocity magnitude degraded at the injector exit, and the secondary flow strength through the injector orifice accentuated due to cavitation.

• Journal of Radiation Protection and Research
• /
• v.10 no.2
• /
• pp.130-136
• /
• 1985

The activity measurement of a solution of $^{133}Ba$ which is an electron capture nuclide was carried out by the ${\beta}-{\gamma}$ coincidence method. The counting rates at the ${\beta}-,\;{\gamma}-$, and coincidence-channels were measured using a $4{\pi}$ proportional counter and two NaI(Tl) scintillation detectors. The specific activity of the solution calculated by the efficiency extrapolation was $(1151.01{\pm}2.99)kBqg^{-1}$ at the reference time(00h UT, 03-15-84). According to an international comparison of activity measurements organized by the Bureau International des Poids et Mesures, this result showed the difference of 0.94% to the mean value derived from the comparison.