• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.513-518
• /
• 2001

As the machining depth increases, the drilling torque increases and fluctuates and the risk of drill failure also increases. Hence, drilling torque control is very important to prevent the drill from failure. In this study, a PID controller was designed to control the drilling torque in a machining center. The plant including the feed drive system, cutting process, and spindle system was modeled for controller design. The Ziegler-Nichols rule was used to determine the controller gain and control action times. The root locus plot was used to tune the controller gain for a certain cutting condition. Also, suggested was a simple method to obtain the tuned controller gain for an arbitrary cutting condition not using the Ziegler-Nichols rule and root locus plot. The cutting torque control, performance of the designed controller and the effect of gain tuning on the control performance were examined.

• Journal of Navigation and Port Research
• /
• v.39 no.6
• /
• pp.457-463
• /
• 2015

A gas turbine engine plays an important role as a prime mover that is used in the marine transportation field as well as the space/aviation and power plant fields. However, it has a complicated structure and there is a time delay element in the combustion process. Therefore, an elaborate mathematical model needs to be developed to control a gas turbine engine. In this study, a modeling technique for a gas generator, a PLA actuator, and a metering valve, which are major components of a gas turbine engine, is explained. In addition, sub-models are obtained at several operating points in a steady state based on the trial running data of a gas turbine engine, and a method for controlling the engine speed is proposed by designing an NPID controller for each sub-model. The proposed NPID controller uses three kinds of gains that are implemented with a nonlinear function. The parameters of the NPID controller are tuned using real-coded genetic algorithms in terms of minimizing the objective function. The validity of the proposed method is examined by applying to a gas turbine engine and by conducting a simulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.4
• /
• pp.332-337
• /
• 1997

디스크립터(Descriptor) 표현은 상태공간 표현을 확장시킨 일반적인 시스템의 기술방법으로 파라미터의 물리적인 구조를 보존하고 있으며, 임펄스를 포함한 현상을 기술할 수 있다. 또한, 대규모 시스템의 모델화가 용이하며, 프로퍼(Proper)이지 않은 시스템을 기술할 수 있고 구속조건을 가진 동적시스템의 기술이 가능하는 등의 특징을 지니고 있다. 그러나, 디스크립터 시스템의 해는 미분항을 포함하고 있으므로 노이즈 및 파라미터 변동에 대해서 매우 민감하여, 관측기설계시 강인(Robust)한 관측기설계가 요구된다. 본 논문에서는 디스크립터 시스템에 대해 로바스트 관측기의 일종인 비례적분(PI) 관측기의 설계에 대해서 논한다. 먼저, 디스크립터 시스템에 대한 PI 관측기의 존재조건을 유도하였으며, 체계적인 설계법을 보였다. 또한, PI 관측기의 존재조건이 Rosenbrock의 가관측 조건하에서 간단히 보여지며, 이것은 시스템 행렬의 Rank 조건에 의해 쉽게 구해질 수 있다.

• Composites Research
• /
• v.17 no.4
• /
• pp.18-24
• /
• 2004

In this paper, active shape control of composite structures actuated by shape memory alloy (SMA) wires is presented. The thermo-mechanical behaviors of SMA wires were experimentally measured. Hybrid composite structures were established by attaching SMA actuators on the surfaces of graphite/epoxy composite beams using bolt-joint connectors. SMA actuators were activated by phase transformation, which induced by temperature rising over austenite finish temperature. In this paper, electrical resistive heating was applied to the hybrid composite structures to activate the SMA actuators. For (aster and more accurate shape/deflection control of the hybrid composite structure, PID feedback controller was designed from numerical simulations and experimentally applied to the SMA actuators.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.3
• /
• pp.131-137
• /
• 1996

The existing digital governors are in the beginning stage. Placing the focus on the marine site, most of the digital governors developed are still using the simple PID algorithm. But, the performance of a diesel engine is widely changed according to the parameters of the PID controller. So, this article describes a new method to adjust the parameters of the PID controller in a marine digital governor. In this paper, the diesel engine is considered as a nonoscillatory second order system. A new method to adjust the parameters of the PID controller for speed control of a diesel engine is proposed by means of the model matching method. Also, the simulations by numerical methods are carried out in cases of the exact understanding or out of the parameters of a diesel engine respectively. And this paper confirms that the proposed new method here is superior to Ziegler & Nichols's method through the comparisons and analysis of the characteristics of indicial responses.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.53-59
• /
• 1990

In the control of robot manipulators, this paper presents a design of a new variable structure model following controller(VSMFC) using computed torque method (CTM). A sufficient condition for the existence of a sliding mode is derived by Lyapunov function. The reference model is a double integrators and the acceleration input consists of a proportional-derivative controller for the purpose of the stabilization of system and the desired performance. The proposed control scheme which consists of upper bounded and estimated value of each term of the manipulator of matrix inversion. Therefore the simulation results show that this controller is improved to the convergence of desired trajectories.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.221-230
• /
• 1988

In the microcomputer-based velocity control for an electro-hydraulic servo system, the effects of control methods and control hardware on the performance of the system were investigated. Experiments were carried out with PID and deadbeat controllers using 8 or 16 bit microprocessor and 8 or 12 bit A/D and D/A converters. It is found that the transient response of the system is better with PID controller than with deadbeat controller. When the number of bits of the microprocessor and converters are small, it is also found that amplitude quantization due to limited word-length gives significant effects on transient responses of the system. Analytically predicted step responses are in good agreement with experimental ones.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.4
• /
• pp.87-94
• /
• 2004

Recently, technical trend in machine tools is focused on enhancing of speed, accuracy and reliability. The high speed usually results in thermal displacement and structural deformation. To minimize the thermal effect, precision machine tools adopt a high precision cooling system. This study proposes a temperature control for an oil cooler system using Pill control with fuzzy logic. In the cooler system, refrigerant flow rate is controlled by rotational speed of a compressor, and outlet oil temperature is selected as the control variable. The fuzzy control rules iteratively correct PID parameters to minimize the error and difference between the outlet temperature and the reference temperature. Here, ambient temperature is used as the reference one. To show the effectiveness of the proposed method, a series of experiments are conducted for an oil cooler system of machine tools, and the results are compared with the ones of a conventional Pill control. The experimental results show that the proposed method has advantages of faster response and smaller overshoot.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.96-106
• /
• 2001

As the drilling depth increases, the cutting torque increases and fluctuates, which can lead to the machine tool vibration, severe tool wear, and catastrophic tool breakage. Hence, cutting torque control is very important to improve productivity in drilling. In this paper, a PID controller was designed to control the drilling torque. The plant including the feed drive system, cutting process and spindle drive system was modeled for controller design. The Ziegler-Nichols method was used to determine the controller gain and control action times and the root locus plot was used to tune the controller gain for a certain cutting condition. Also, suggested was a simple method to obtain the tuned controller gain for an arbitrary cutting condition not using the Ziegler-Nichols method and the root locus plot. The performance of the designed controller and the effect of controller gain tuning were verified from experiments.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.26-30
• /
• 2001

Controller refinement scheme to improve the performance of a conventional system automatically in frequency domain is proposed. The controller automatic tuning method features using experimental frequency responses of the conventional closed-loop system, the conventional controller, and the improved closed-loop system, instead of poorly modeled plant due to non-linearities and disturbances. The improved closed-loop system characteristics is automatically acquired by the con-ventional closed-loop system characteristics and the proposed performance index in system bandwidth. And the proper controller is realized by least squares approximation in frequency domain. To testify the usefulness of the approach, the path tracking control of robot arm is performed. Experimental results and analytic results are well-matched.