Journal of Advanced Marine Engineering and Technology
/
제37권1호
/
pp.29-34
/
2013
용접과정 중에 용접부가 공기에 노출되면 용접성능을 약화시킨다. 불활성가스 텅스텐 아크용접(GTAW)법을 사용하여 티타늄 용접을 하는 경우 용접부가 자주/적색, 청색, 노란색, 회색, 흰색 등의 빛깔을 보이면 이는 용접 시 공기 중의 산소와 질소에 오염된 것을 의미한다. 따라서 용접부를 대기로부터 보호하기 위한 방법으로 실딩 가스를 사용한다. 이것은 대기에 의한 오염을 방지할 뿐만 아니라 용착부와 열영향부도 상온까지 냉각될 때까지 대기로부터 차단시킨다. 본 연구에서는 Trailing Shielding Jig 의 모양과 형태 그리고 토치보호($13{\sim}20{\ell}/min$), 후방보호($22{\sim}30{\ell}/min$), 이면보호($25{\sim}30{\ell}/min$)등 건전한 용접부에 적합한 실딩 가스에 대한 결과를 도출하였다.
It was attempted to improve the wear resistance of Al alloy under the load condition by making a formation of the thicker surface hardening alloy layers. The thicker surface hardening alloy layers were formed on 6061 Al alloys overlayed by MIG and TIG welding process with Cu powders feeding. The characteristics of hardening and wear resistance have been investigated in relation to the microstructures of alloyed layers, with a selection of optimum alloying conditions for formation of overlaying layer. The results obtained were summarized as follows With increasing feeding rate of Cu powders by MIG welding, the hardness and specific wear of the overlay weld alloys were increased. It is considered that these high hardness and specific wear of overlay weld alloys were due to the formation of Θ($Al_2Cu$) phases. With increasing feeding rate of Cu powders by TIG welding, the hardness and specific wear of the overlay weld alloys were increased in feeding rates 12 and 18g/min. However, the hardness and specific wear were decreased in the powder feeding rate 38g/min. It is considered that considered that decrease of hardness and specific wear in the powder feeding rate 38g/min due to formation of ${\gamma}$($Al_4Cu_9$) phases.
알루미늄과 그 합금은 항공우주산업이나 가정용 기물 밖에도 일반공업용 재료로써 차량 토목건축 조선 화학식품 전기와 원자로등 많은 공업분야에 널리 사용되고 있다. 최근에 용접법의 발전과 합금의 개발에 의하여 알루미늄 합금은 보통의 금속재료에 대하여 사용하고 있는 거의 대부분의 접합법에 의하여 용이하게 접합할 수가 있다. 그 중에서도 불활성 가스 아아크용접이 널리 사용 되고 있는 것은 주지의 사실이나 알루미늄 합금의 종류는 용도에 따라서 다양 다종이여서 그 종류에 의하여 용접성(weldability)의 난이가 있음으로 합금의 특징이나 용접부의 거동을 잘 알 고서 모재와 용가재의 선정에 충분한 주의와 세심한 관찰이 필요하다.
Friction stir welding results in low distortion and high joint strength compared with other welding procedures, and is able to join all aluminium alloys that are not considered as virtually weldable with classical liquid state techniques. The comparative study on high cycle fatigue properties between A16005-T6 friction stir welds and MIG weld joints have been performed and fracture mechanisms for the fatigue specimens were investigated. Although mechanical properties are lower than the corresponding base material, FSW joints of A16005-T6 become higher at tensile and fatigue strength in comparison with the traditional fusion weld(MIG). The fracture surfaces of FSW and MIG fatigue specimens cleary show different aspects of the fracture morphology. MIG weldments were characterized by voids and cleavage(brittle fracture) but FSW specimens showed the presence of ductile fracture surface.
GTA (Gas Tungsten Arc)용접은 불활성 분위기에서 용접이 이루어지기 때문에 타 아크용접법에 비해 용접부 품질이 우수하여 고품질이 요구되는 산업분야에 널리 이용되고 있다. 하지만 스테인리스강으로 pipe를 제조하기 위해 GTA 용접을 적용할 경우, Laser 및 고주파 용접 (HFIW)에 비해 용접부 품질 및 용접속도가 낮기 때문에 pipe를 제조하는 산업에서 적용에 제한을 받고 있다. 하지만, GTA는 laser 혹은 HFIW에 비해 가격이 1/10수준으로 낮고, 용접부 gap tolerance 및 용접면 관리범위가 넓은 장점이 있기 때문에 GTA의 용접속도 및 용접품질을 향상시키기 위한 연구가 꾸준히 진행되고 있다. 일반적으로 스테인리스강 GTA용접 시 용접속도를 향상시키기 위해, 모재의 성분 제어 (합금성분 최적화-Al, S, Se, O등), Flux 도포 기술 (산화물을 용접전에 도포하여 용접속도 향상) 및 혼합보호가스 적용 등이 있다. 스테인리스강 용접 시 보호가스로는 용접부 품질을 확보하기 위해 Ar을 주로 사용하고 있다. 하지만 용입 특성을 향상시키기 위해 아크의 온도를 높일 수 있는 He, 혹은 $H_2$ gas를 단독 혹은 혼합하여 사용하고 있다. 오스테나이트계 스테인리스의 경우 용입특성을 향상시키기 위해 Ar에 $H_2$를 2~10%정도 혼합하여 사용하고 있다. 페라이트계 스테인리스강은 수소에 대한 고용도가 상대적으로 작아 용접부 수소 취화를 일으킬 수 있기 때문에 적용에 제한을 받고 있어 그 대안으로 산소를 극히 소량을 혼합하여 용입성 향상에 대한 연구가 보고 되고 있다. 따라서 본 연구에서는 페라이트계 스테인리스강의 용입특성을 향상시킬 목적으로 Ar에 산소를 미량 첨가 (1%미만) 하여 용접전류 및 산소 함량에 따른 용입특성의 변화에 대해 연구하였다. 또한 기계적인 물성 및 부식특성을 평가하였고, 최종적으로 실용화 가능성을 파악하기 위해 용접전극의 수명 테스트를 실시하였다. 실시한 결과, 산소가 첨가량 증가 할수록 용입특성은 상승하였으며, 기계적인 물성 또한 산소를 첨가하지 않은 경우에 비해 거의 유사한 값을 얻을 수 있었다, 하지만 산소함량이 증가 할수록 전극의 수명은 감소하여 교체주기가 증가함을 알 수 있다. 본 연구를 통해 얻어진 기술을 상용화시키기에는 극복해야할 문제가 있지만, 소재 합금성분 설계 시 용접생산성 향상위한 산소성분 범위를 제시할 수 있으리라 판단된다.
As a considerable, experimental approach, an Auto-carriage type of $CO_2$ welding machine and a MIG(Metal Inert Gas) welding robot under inert gas atmosphere were utilized in order to realize Al 5083 welding applied to hull and relevant components of green Al leisure ships. This study aims at investigating the effect of welding conditions(current, voltage, welding speed, etc) on thermal deformation that occurs as welding operation and tensile characteristics after welding, by using Al 5083, non-ferrous material, applied to manufacturing of co-environmental Al leisure ships. With respect to welding condition to minimize the thermal deformation, 150A and 16V at the wire-feed rate of 6mm/sec were acquired in the process of welding Al 5083 through an auto carriage type of $CO_2$ welding feeder. As to tensile characteristics of Al 5083 welding through a MIG welding robot, most of tensile specimens showed the fracture behavior on HAZ(Heat Affected Zone) located at the area joined with weld metal, except for some cases. Especially, for the case of the Al specimen with 5mm thickness, 284.62MPa of tensile strength and 11.41% of elongation were obtained as an actual allowable tensile stress-strain value. Mostly, after acquiring the optimum welding condition, the relevant welding data and technical requirements might be provided for actual welding operation site and welding procedure specification(WPS).
In this study, the experiments were carried out for the purpose of establishment of the arc sparing method which reducing oxides or oxide film by using the inert gas as the carrier gas of atomizing particles. Main results obtained are as follows; 1. Oxides and oxide film which lower the adhesion strength are largely reduced by using the inert gas as the carrier gas of atomizing particles, and adhesion strength of coating film are improved. 2. The coating film characteristics appear to be no difference between the inert gas arc spraying in air environment and that in argon gas environment. 3. Inert gas arc spraying using argon as the carrie gas has higher reduction rate of composition element in coating film than compressed air spraying does.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.