• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.101-109
• /
• 2016

The purpose of this research was to develop a flat panel display device's glass etchant which can replace hydrofluoric acid. The glass etchant was composed of 18~19% wt% of ammonium hydrogen fluoride, 24~25 wt% of sulfuric acid, 45~46 wt% of water, 4~5 wt% of sulfate and 7~8 wt% of fluoro-silicate. By replenishing the etchant which has the amount of 5% of initial solution's mass, it was possible to reuse the etchant continuously. The developed etchant showed $5{\mu}m/min$ of etching rate at $30^{\circ}C$. The reusable etchant, with replenishing 5% of initial etchant mass showed the stable etching rate, which has the deviation of less than $0.1{\mu}m/min$ etching rate. The glass surface of flat panel display device created from our etching process was in good condition with any defects such as pin hole and dimple.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.71-78
• /
• 2005

The purpose of this study is to suggest a hyperfine maskless writing technique by using the nanoindentation and HF wet etching technique. Indents were made on the surface of Pyrex7740 glass by the hyperfine indentation process with a Berkovich diamond indenter, and they were etched in $50\;wr\%$ HF solution. After etching process, convex structure was obtained due to the deformation-induced hillock phenomena. In this study, effects of indentation process parameters (etching time, normal load, loading .ate, hold-time at the maximum load) on the morphologies of the indented surfaces after isotopic etching were investigated from an angle of deformation energies. Finally, sample characters were written to show the possibility of the application.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.182-185
• /
• 2005

Indentation pattern and line pattern were machined on borosilicate(Pyrex 7740 glass) surface using the combination of mechanical machining by $Nanoi-indenter\circledR$ XP and HF wet etching, and a etch-mask effect of the affected layer of the nano-scratched and indented Pyrex 7740 glass surface was investigated. In this study, effects of indentation and scratch process with etching time on the morphologies of the indented and scratched surfaces after isotropic etching were investigated from an angle of deformation energies.

• Korean Journal of Materials Research
• /
• v.8 no.9
• /
• pp.871-875
• /
• 1998

High aspect ratio microstructures were fabricated by photolithography. The material for the microstructure was photosensitive glass which has good mechanical and electrical insulation properties. The photosensitive glass was exposed to ultraviolet light at 312nm through a chromium mask in which the structures are drawn. After heat treatment process over $500^{\circ}C$, the photosensitive glass was etched in a 10% hydrofluoric acid solution with ultrasonic conditions. Final dimension of the micro-framework was greatly dependent on the thickness of photosensitive glass, mask pattern, ultraviolet light exposure and etching conditions. The maximum aspect ratio of the micro-framework obtained from this work was over 30.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.725-730
• /
• 1996

The key process in silicon surface micromachining is the selective etching of a sacrificial layer to release the silicon microstructure. The newly developed anhydrous HF/$CH_3$OH gas phase etching of TEOS (teraethylorthosilicate) sacrificial layers onto the polysilicon and the nitride substrates was employed to release the polysilicon microstructures. A residual product after TEOS etching onto the nitride substrate was observed on the surface, since a SiOxNy layer is formed on the TEOS/nitride interface. The polysilicon microstructures are stuck to the underlying substrate because SiOxNy layer does not vaporize. We found that the only sacrificial etching without any residual product and stiction is TEOS etching onto the polysilicon substrate.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.225-228
• /
• 2005

The purpose of this study is to investigate effects of the plastic/elastic deformation energy on wet etching characterization on the surface of material by using the nanoindentation and HF wet etching technique. Indents were made on the surface of Pyrex 7740 glass by the hyperfine indentation process with a Berkovich diamond indenter, and they were etched in $50\;wt\%$ HF solution. After etching process, convex structure was obtained due to the deformation-induced hillock phenomena. In this study, effects of indentation process parameters (normal load, loading rate) on the morphologies of the indented surfaces after isotopic etching were investigated from an angle of deformation energies.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.8
• /
• pp.909-914
• /
• 2007

Fluorine compounds are the essential chemicals for wet processes of semiconductor and LCD production line. Problems of conventional treatments for fluoride wastewater are their high operation costs and low fluoride removal capacity. In this study, cement paste containing various Ca-bearing hydrates such as portlandite, calcium silicate hydrate(CSH), and ettringite was investigated for fluoride removal. The objectives of this study are to assess the feasibility of using cement paste cured mixture of cement and water as an alternative agent for treatment of fluoride wastewater and to investigate fluoride removal capacity of the cement paste. The performance of cement paste was comparable to that of lime in the kinetic test. In column experiment where the effluent fluoride concentrations were below 0.5 mg/L. Then the leached calcium reached the maximum level of 800 mg/L. The nitrate reduced to the level of less than 10 mg/L. Nitrate in the wastewater was exchanged with interlayer sulfate of these cement hydrate LDHs. Phosphate concentration could be reduced to 10 mg/L by forming calcium phosphate. These results indicate that the cement paste generally has advantageous characteristics as an economical and viable substitute for lime to remove fluoride.

• Analytical Science and Technology
• /
• v.27 no.3
• /
• pp.167-171
• /
• 2014

Hydrofluoric acid (HF), a typical inorganic acid, has been used in the industry for its various usage and classified as the toxic compound, because it can cause the pneumonia and pulmonary edema when it was exposed to respiratory organs. The official environmental analytical method for fluorine and its compound in waste has not been developed. For this reason, we have faced some problem to treat the contaminated wastes by the HF leakage from industrial process. In this study, prepared for analytical method for combustible waste (crop, trees, etc.) generated from HF leaking accident and to be applied as the official analytical method for fluorine contaminated waste when the fluorine and its compound will be regulated as a hazardous material by the waste management law later.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.264.2-264.2
• /
• 2014

비휘발성 메모리는 전원이 공급되지 않아도 저장된 정보를 계속 유지하는 메모리로써 현재 다양한 차세대 전자소자의 집적화 구현을 위해 저전압 동작 및 저장능력의 향상 등에 대한 연구가 활발히 진행되고 있다. 이때 삽입되는 전하저장층의 경우 기존 널리 이용되는 질화막(SiNx) 외에 최근에는 산화 알루미늄(Al2O3) 등의 고유전상수 물질 뿐만 아니라, 밴드갭 조절을 통해 전하저장능력을 향상시키는 산화막(SiOx)에 대한 연구도 진행 중이다. 이번 연구에서는 전하저장능력을 향상시키기 위해 전하저장층으로 산화막을 이용할 뿐만 아니라, 기존의 평편한 구조가 아닌 표면 조절을 통해 전하저장능력을 보다 향상시키고자 한다. 또한 이번 연구에서는 비휘발성 메모리 소자의 응용을 위해 우선적으로 금속-절연체-반도체 형태의 MOOxOyS 구조를 이용하였다. 이 때 실리콘 표면적을 변화시키기 위해 이용된 실리콘 웨이퍼는 1) 평편한 실리콘, 2) 수산화암모늄, 이소프로필 알코올 및 탈이온수를 혼합한 용액에 식각시킨 삼각형 구조, 3) 불산, 질산 및 아세트산을 혼합한 용액에 식각시킨 라운드 구조이다. 정전용량-전압 측정을 통해 얻어진 메모리 윈도우는 1) 평편한 실리콘의 경우 약 5.1 V, 2) 삼각형 구조의 경우 약 5.3 V, 3) 라운드 구조의 경우 약 5.9 V를 얻었다. 이 때, 라운드 구조의 경우 가장 넓은 표면적으로 인해 상대적으로 전하트랩이 가장 많이 되어 메모리 윈도우가 가장 커지는 특성을 볼 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.29-32
• /
• 2009

Dense and periodic arrays of nano-sized holes were patterned in oxide thin film on GaAs substrate. To obtain the nano-size patterns, self-assembling diblock copolymer was used to produce thin film of uniformly distributed parallel cylinders of polymethylmethacrylate (PMMA) in polystyrene (PS) matrix. The PMMA cylinders were removed with UV expose and acetic acid rinse to produce PS nanotemplate. By reactive ion etching, pattern of the PS template was transferred to under laid silicon oxide layer. Transferred patterns were reached to the GaAs substrate by controlling the dry etching time. We confirmed the achievement of etching through the removing oxide layer and observation of GaAs substrate surface. Optimized etching time was 90 to 100 sec. Pore sizes of the nanopattern in the silicon oxide layer were 20~22 nm.