• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1931-1938
• /
• 2012

A by-pass path in wireless sensor networks is the alternative path which be able to forward data when a routing path is being broken. One reason of depleting energy is occurred by the path. The method for solving prior to addressed the problem is proposed. However, this method may deplete radio resource. The best path has advantage that network lifetime of sensor nodes is prolonged; on the contrary, in order to maintain the best path it have to share their information between the entire nodes. In this paper, we propose the best path searching algorithm in the distributed three dimensional sensor networks. Through the neighboring informations sharing in the proposed method, the proposed algorithm can decide the best k-path as well as the extension of network lifetime.

• Journal of the Korean Vacuum Society
• /
• v.21 no.5
• /
• pp.258-263
• /
• 2012

Fe-diluted Si alloys grown on p-type Si (100) substrates by pulsed-laser deposition method were studied for structural, electrical, and magnetic properties. The X-ray diffraction patterns for these alloy samples showed a few of peaks with cubic structures such as FeSi, $Fe_3Si$, and $Fe_4Si$. The Fe-composition in alloys are confirmed as Fe atomic percent about 1.25~6.49 % from energy dispersive spectroscopy measurement. The resistivity as a function of the reciprocal temperature was indicated an exponential increase with two activation energies of 5.21 and 7.79 meV. The maximum value of the magnetization at 10 K was about 100 emu/cc, and the ferromagnetism was also observed until 350 K from total magnetization as a function of temperature with applied magnetic field of 3,000 Oe.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.57-62
• /
• 2010

Renewable energy and smart grid become the focus of attention of industry. The smart grid is an intelligent system which maximizes the efficiency of energy and it needs to monitor the amount of power generation and power consumption continuously. Remote Monitoring System(RMS) is very useful for monitoring the power generation and consumption, but mostly they are implemented on the wire communication. In this paper, we propose a wireless sensor network based remote power monitoring system. And as an application, a new anti-islanding method with the proposed RMS is presented. An experimental micro grid system is implemented to verify the proposed RMS and anti-islanding method.

• Journal of Hydrogen and New Energy
• /
• v.29 no.2
• /
• pp.170-180
• /
• 2018

After $MoS_2$ catalyst was prepared at 1, 30, and 70 atm, the hydrothermal pressure effect over preparation of $MoS_2$ was investigated in terms of catalyst characterization and direct methanation. Multifaceted characterization techniques such as XRD, BET, SEM, TPR, EDS, and XPS were used to analyze and investigate the effect of high pressure over the preparation of surface and bulk $MoS_2$ catalyst. Result from XRD, SEM, and BET demonstrated that $MoS_2$ was more dispersed as preparation pressure was increased, which resulted finer $MoS_2$ crystal size and higher surface area. EDS result confirmed that bulk composition was $MoS_2$ and XPS result showed that S/Mo mole ratio of surface was about 1.3. TPR showed that $MoS_2$ prepared at 30 atm possessed higher active surface sites than $MoS_2$ prepared at 1 atm and these sites could contribute to higher CO yield during methanation. Direct methanation was used to evaluate the CO conversion of the both catalysts prepared at 1 atm and 30 atm and reaction condition was at feed mole ratio of $H_2/CO=1$, GHSV=4800, 30 atm, temperature($^{\circ}C$) of 300, 350, 400, and 450. $MoS_2$ prepared at 30 atm showed more stable and higher CO conversion than $MoS_2$ prepared at 1 atm. Faster deactivation was occurred over $MoS_2$ prepared at 1 atm, which indicated that preparation pressure of $MoS_2$ catalyst was the dominant factor to improve the yield of direct methanation.

• Computational Structural Engineering
• /
• v.6 no.1
• /
• pp.127-135
• /
• 1993

This paper summarizes a study on the application of viscoelastic dampers as an energy dissipation device in the frame structure. It can be concluded that, even at high temperatures, the viscoelastically damped structure can achieve a significant reduction of structural response as compared to the case with no dampers added. Empirical formulae for estimating the dynamic properties of the viscoelastic damper are established based on the regression analysis using data obtained from component tests of the damper. The structural damping with added dampers can be satisfactorily estimated by the modal strain energy method and the derived empirical formulae. Numerical simulations using conventional modal analysis methods are also carried out to predict the dynamic response of viscoelastically damped structures under seismic excitations. Comparison between numerical simulations and test results shows very good agreement. Based on the above studies, a design procedure for viscoelastically damped structures is present . This design procedure fits naturally into the conventional structural design flow-chart by including damping ratio an additional design parameter.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.1
• /
• pp.11-23
• /
• 2010

A sacrificial member with aluminum foam of excellent energy absorption capacity was proposed for the protection of significant structures. Parametric studies of explicit finite element analyses were performed to investigate the pressure mitigation of close-range air-blasts. The scaled distance of the blast had a range of Z=0.48~0.95 and an empirical blast load function was utilized. The analytical parameters of the aluminum foam were density, thickness and the existence of a cover sheet. Analytical results showed that the transmitted pressure can be controlled to have a similar level of yield values of the foam by using a foam with low density and higher thickness. As the blast load increased, the sacrificial member needed to have higher density and thickness. A cover sheet of the foam clearly showed its effect on the wider distribution of blast pressure. It is necessary to determine the design parameters of sacrificial foams considering different energy dissipation capacities according to the scaled distance.

• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.765-774
• /
• 1995

The hot deformation behaviour of particulate reinforced aluminium 6061 Al composite were investigated by hot compression tests in the temperature range from 623K to 823K with strain rate of 10$^{-3}$ ~5.0 S$^{-1}$ . The effect of reinforced particulate volume fraction, mean diameter on the high temperature flow stress has also been studied. Experimental results showed that the increase in the volume fraction of reinforcement contributed to the rising of yield stress, but the stress above the yield point appeared to be steady state at all volume fractions. The apparent activation energy for deformation was 290KJ/mo1 for unreinforced 6061 Al, 327KJ/mo1 for 6061 Al-20vo1.% SiC composite and 531KJ/mo1 for 6061 Al-20vo1.%A1$_2$O$_3$composite. It appeared that $Al_2$O$_3$reinforced composites was more difficult to hot deform.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.5
• /
• pp.565-573
• /
• 2016

Wi-Fi Direct standard technology(Wi-Fi Peer to Peer Technical Specifications v1.2, 2010) was designed for allowing peer to peer communication between two or more devices and various products which have been currently manufactured such as smart phone and smart TV have already provided this technical function. In this technology the role of Coordinator in Wi-Fi infrastructure would be matched to GO(Group Owner) which needs relatively high energy resource and computation power due to the high probability for allowing 3rd-party connection, however, the current standard specification would be limited in terms of energy distribution because it has not included a process to determine the role of GO. To address above problem, this paper classified considerable parameters into the general parameters for the physicality of devices and the specific parameters for considering the role position depending on use-case scenario, and proposed a new method called DIVA to help efficiently determining GO role from the member devices of Wi-Fi Direct network. Furthermore the effect of this mechanism was proved via simulation-based experiments.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.497-506
• /
• 2006

The precast concrete beam-column connectors for the high-rise office buildings were investigated experimentally in this study. The specimens of general precast beam-column connector which is used in a domestic site, specimen of DDC(dywidag ductile connectors) of Germany, and specimen of DDC with post-tensioning and modified DDC with post-tensioning were constructed and tested to verify the safety. The DDC with and without post-tensioning showed reliable joint strength and ductility but failed in critical inclined shear crackings at the column. The modified one showed better behaviors in tests because they did not show critical column crackings at failure. The use of prestressing did not helpful significantly to increase the strength and ductility of connectors but helpful only to develop self-centering behavior for stability.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.2
• /
• pp.119-130
• /
• 2009

This article reviews recent R&D trends in SOFC development with an emphasis on industries that can produce the SOFC stack and power generation system. SOFC is an electrochemical device that can convert the chemical energy of fuel into the electrical energy with environment friendly system and high efficiency. SOFC power generation system could be classified as the portable power generation system, auxiliary power unit(APU), residential power generation(RPG) and large size distributed power generation. In the case of more than 10kW system, the major R&D trends are focused on the tubular type SOFC system with high efficient and long term stability to meet the commercialization of SOFC power generation system.